Which manufacturer produces Navigator engine oil?

1 Answers
GiselleMarie
07/29/25 10:14am
Navigator engine oil is Shell Helix oil, originally produced in the Netherlands. The following is an introduction about engine oil: 1. Introduction: Engine oil, motor oil, or engine lubricant is a substance enhanced with additives in base oil, mainly containing anti-wear additives, detergents, dispersants, and multi-grade viscosity index improvers. Engine oil is used for lubricating internal combustion engines. 2. Functions: The main functions of engine oil are to reduce friction and wear of moving parts, and to remove sludge (one of the functions of dispersants) and varnish (detergents) from the engine. It also neutralizes acids from fuel and lubricant oxidation (detergents), improves the sealing of piston rings, and cools the engine by carrying away heat from moving parts. 3. Performance: Most engine oils are made from heavier, more viscous petroleum hydrocarbon base oils derived from crude oil, with additives to improve certain properties. Most typical engine oils mainly consist of hydrocarbons with 18 to 34 carbon atoms per molecule.
Was this review help?
4
1
Share
More Forum Discussions

How to Start Without Stalling?

If you don't press the accelerator slightly when starting on an uphill slope, the engine may stall due to insufficient idle speed to move the vehicle. Slowly release the clutch pedal until the vehicle starts to vibrate, then hold it at this position without further lifting to prevent stalling. When starting, quickly release the clutch until the vehicle reaches the semi-engaged state, then hold the clutch steady and rapidly release the brake with your right foot.
10
4
Share

What are the main impacts of foggy weather on safe driving?

The main impact of foggy weather on safe driving is reduced visibility and unclear sight. In light fog areas, it is necessary to appropriately reduce driving speed and increase the distance between vehicles. The following are specific requirements for driving in foggy conditions: When visibility is between 200 meters and 500 meters: You must turn on the anti-glare low beam, width marker lights, and tail lights, with speed not exceeding 80 km/h, and maintain a distance of more than 150 meters between vehicles. When visibility is between 100 meters and 200 meters: You must turn on the fog lights, anti-glare low beam, width marker lights, and tail lights, with speed not exceeding 60 km/h, and maintain a distance of more than 100 meters between vehicles. When visibility is between 50 meters and 100 meters: In addition to turning on the above lights, speed should not exceed 40 km/h, and maintain a distance of more than 50 meters between vehicles. When visibility is below 50 meters, it is considered extremely dense fog, and public security authorities may implement traffic management measures such as partial or full closure of highways according to regulations.
17
2
Share

Do I need to replace tires at 50,000 kilometers?

Tires at 50,000 kilometers may not need immediate replacement. The process and precautions for tire replacement are as follows: Tire replacement process: Loosen the screws; lift the vehicle with a jack; remove the screws securing the wheel (counterclockwise to loosen, clockwise to tighten); take off the old tire; install the new wheel. Precautions for tire replacement: Choose tires of the same specifications; pay attention to installation direction and inflation; check tire pressure; perform wheel alignment after replacement; when removing the tire, slightly loosen the fixing screws before partially lifting the vehicle with a jack; select tires with guaranteed quality.
6
3
Share

What is the 'A' in a circle on the car?

It is the STT Intelligent Fuel-saving System, which is a system that controls the engine start and stop. Below is relevant information about the STT Intelligent Fuel-saving System: 1. Introduction to the STT Intelligent Fuel-saving System: STT is short for STOP&START. The STT Intelligent Fuel-saving System is a system that controls the engine start and stop. The system uses a computer to determine the vehicle's status, such as when the vehicle is in a stopped state due to a red light or traffic jam. The computer can control the engine to automatically stop running, and during the stop phase, it does not affect the use of in-car devices like the air conditioner or audio system. 2. Function of the STT Intelligent Fuel-saving System: By implanting an enhanced motor with idle start-stop functionality into a traditional engine, the system ensures that the engine completely shuts off when the vehicle meets the idle stop conditions. When the vehicle needs to start moving again, the idle start-stop motor system quickly responds to the driver's start command, rapidly starting the engine for seamless transition, thereby significantly reducing fuel consumption and exhaust emissions.
20
3
Share

What Certificates Are Required to Become a Taxi Driver?

Required certificates include a driver's license, road transport practitioner qualification certificate, taxi driver's work permit, vehicle registration certificate, and health certificate. The first two certificates are valid nationwide, while the work permit is only valid locally. With the first two certificates, if you want to drive a taxi in another province, you only need to apply for the local taxi driver's work permit. If you have the above certificates, a taxi driver should also meet the following conditions: 1. Driver's License: Hold a driver's license that matches the permitted vehicle type and has a driving experience of at least two years. 2. Household Registration: Have a permanent residence in the local jurisdiction, be aged between 18 and 55, have good conduct, and no criminal record. 3. Character: Possess good professional ethics and at least a junior high school education, be in good health, and free from infectious diseases. 4. Familiarity with Routes: Be familiar with the streets, routes, and geographical locations within the jurisdiction. 5. Qualification Certificate: Obtain the certificate after passing the training, examination, and review process.
11
1
Share

How to Check a Car's Displacement?

The simplest and most direct method is to look at the vehicle's identification plate. The vehicle identification plate is a label that indicates the basic characteristics of the vehicle, including the manufacturer's brand. You can also visit professional inquiry websites to check. You can search for the keyword "motor vehicle environmental protection" on Baidu. Another way is to find the vehicle's factory certificate, provided it is a new car. Check the vehicle's factory certificate for the information. Alternatively, you can personally take the vehicle's registration certificate to the environmental protection window at the vehicle management office or the local motor vehicle pollution management center. The staff there will assist in checking the information.
4
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.