Which manufacturer produces Jetour vehicles?

Where is the reverse light switch located on a Prado?

The reverse light switch is located on the transmission. The position varies depending on the engine type, so you may need to locate it yourself. Reverse lights: Reverse lights are installed at the rear of the vehicle to illuminate the road behind and alert vehicles and pedestrians that the car is reversing. All reverse lights are white. Method for replacing reverse lights: Open the trunk and pry open the black plastic cover at the right rear taillight. The cover is usually secured with plastic clips. After removing the cover, you will see two fixing screws. Use a wrench to remove and set them aside. Next, remove the entire taillight assembly by pushing it firmly to the right side of the vehicle while holding it to prevent dropping, as it is secured with clips. Once the taillight is removed, locate the reverse light. Without disconnecting the plug, rotate it counterclockwise to remove it, then install the new reverse light.

13

3

Share

Is the Civic a Japanese car?

Honda Civic is a Japanese car, with domestic versions available. The Honda Civic is a model under the Honda brand. Since the birth of the first-generation CIVIC (Civic) in 1972 (as of March 1, 2020), it has undergone 8 generations of inheritance and 40 years of experience. In 2006, the eighth-generation CIVIC (Civic) officially entered China. Relevant information about joint-venture cars is as follows: 1. Introduction: A project jointly established by Chinese and foreign investors. The Chinese side contributes by providing land and factory usage rights, and capital; foreign investors provide the brand, technology, capital, talent, etc. Joint-venture cars are the products of such collaborations. Foreign parties provide technology, talent, brand, etc., for domestic assembly, but the core technology is still controlled by the foreign side. 2. Joint-venture brands under the FAW Group include: FAW-Volkswagen, FAW-Audi, FAW-Mazda (all produced in Changchun, Jilin), and FAW-Toyota (produced in Changchun, Jilin; Tianjin; and Chengdu, Sichuan).

5

0

Share

Why can't the 3rd gear of the Baojun 560 manual transmission suddenly engage?

Manual transmission can't engage gears for the following reasons: Incorrect gear position: When starting an automatic transmission car, the gear must be placed in P or N position. If placed in R or D position, the car will not start. Some manual transmission cars will also not start if the clutch is not depressed. No antifreeze added: Some car owners add water or inferior antifreeze to their cars, resulting in the entire water circuit freezing in extremely cold winter conditions, causing the engine to crack, the car water pump to fail to operate, the car not to start, and damage to other engine components. Gear lever assembly failure: The internal gears of the gear lever are worn, causing the gear lever to get stuck, making it very difficult to pull back and forth, resulting in the inability to shift gears and difficulty in shifting.

7

1

Share

Is a Lean Fuel System Caused by Fuel Quality Issues?

A lean fuel system is not solely caused by fuel quality issues. Excessive carbon buildup on valves and fuel injectors, damaged mass airflow sensors, and intake system leaks can also lead to a lean fuel system. A lean fuel system is an alarm signal triggered by the engine's oxygen sensor detecting incomplete gasoline combustion. This alarm occurs due to insufficient fuel injection combined with excessive air, resulting in a low concentration of combustible gas. Therefore, addressing this issue requires consideration from two aspects. First, fuel system problems, including clogged fuel injectors due to excessive carbon buildup or insufficient fuel supply caused by a faulty fuel pump. On the other hand, intake system failures, such as a malfunctioning mass airflow sensor or intake leaks, can lead to inaccurate air supply. It is recommended that vehicle owners visit a repair facility to read fault codes using a diagnostic scanner and systematically troubleshoot the issue based on the prompts. A lean fuel system can result in reduced engine power, increased fuel consumption, and in severe cases, engine stalling and difficulty starting. It also causes elevated idle speed, where the engine RPM struggles to drop to idle speed quickly when decelerating. In such cases, removing the spark plugs will reveal white-colored electrodes, confirming an excessively lean air-fuel mixture.

9

1

Share

What are the symptoms of a broken manual transmission shift cable?

Manual transmission shift cable damage manifests as affecting normal gear shifting. Before breaking, gears may be difficult to engage or may not fully engage. You can open the shift box to see the shift cable head detached from the gear head, resulting in an inability to shift gears. Adjusting the shift cable: Adjusting the shift cable requires two people to complete. During adjustment, one person shifts gears while the other adjusts. When pushed into the corresponding gear, do not release until the other person has adjusted the shift cable, then proceed to adjust the next gear until all cables are adjusted to the proper position. Solutions for a frozen shift cable: If the shift cable is found to be frozen, you can first start the car and use the heat generated by the engine at idle to thaw the shift cable. This method is the simplest way to thaw. Alternatively, if the shift cable is frozen, you can remove it, then use warm water to melt the ice on the shift cable. Afterward, spray an appropriate amount of WD-40 as a lubricant, or take a small amount of engine oil, soak the entire shift cable for a while, and then reinstall the shift cable.

6

5

Share

Can You Shift from 3rd Gear to 1st Gear in a Manual Transmission?

Manual transmission allows shifting from 3rd gear to 1st gear, which is known as skip-shifting or upshifting. Manual transmissions permit skip-shifting. Before shifting from 3rd to 1st gear, quickly press the accelerator to raise the engine speed to 3000 RPM, then directly shift from 3rd to 1st gear to ensure a smooth transition. Principle of Skip-Shifting: The difference between each gear in a manual transmission lies in the gear ratio. Cross-gear shifting is achievable with manual transmissions, but due to varying gear ratios, maintaining proper engine speed is crucial. Otherwise, lugging or jerking may occur. Therefore, skip-shifting requires throttle input to maintain appropriate engine speed. Risks of Skip-Shifting: Shifting from 1st to 3rd gear without pressing the accelerator will cause the RPM to drop rapidly, leading to engine knocking or pinging sounds, and may even stall the engine. This results in increased carbon deposits due to incomplete fuel combustion. In severe cases, cylinder walls, pistons, connecting rods, and crankshafts may experience abnormal wear or deformation due to excessive stress.

5

Share

Which manufacturer produces Jetour vehicles?

Where is the reverse light switch located on a Prado?

Is the Civic a Japanese car?

Why can't the 3rd gear of the Baojun 560 manual transmission suddenly engage?

Is a Lean Fuel System Caused by Fuel Quality Issues?

What are the symptoms of a broken manual transmission shift cable?

Can You Shift from 3rd Gear to 1st Gear in a Manual Transmission?

Is the 2019 Grand Cherokee compliant with China's National VI emission standards?

How many points will be deducted for installing a tail box on a motorcycle?

How to Install Mudguards on the Nissan Sylphy?

Where is the Previa engine number located?