Which Lynk & Co 02 model is equipped with a four-cylinder engine?

What are the methods to alleviate fatigued driving?

Here are some methods to alleviate fatigued driving: 1. Play music in the car; 2. Keep the windows open while driving; 3. Wash your face with cold water; 4. Use essential balm; 5. Listen to poetry or articles; 6. Chew gum; 7. Pull over and take a short break. Additional information: 1. Fatigued driving occurs when drivers experience physiological and psychological dysfunction after prolonged continuous driving, leading to decreased driving skills. It affects the driver's attention, thinking, and judgment. 2. Situations that easily lead to fatigued driving include: poor sitting posture and poor blood circulation; driving for more than 4 hours continuously; lack of sleep; poor air quality and ventilation inside the car.

18

5

Share

How is the quality of Xinyi brake pads?

Xinyi brake pads are composed of asbestos-free non-metallic materials and offer good quality. Below is a detailed introduction to Xinyi brake pads: 1. Material of Xinyi brake pads: Xinyi brake pads are made of asbestos-free non-metallic materials. They are heat-resistant, noise-free, and do not damage the drum, making them a top performer among similar products at the same price point. In 2005, they were exported to the United States, making Xinyi the only Chinese manufacturer exporting brake pads. 2. Concept of brake pads: Automotive brake pads, also known as brake linings, refer to the friction materials fixed on the brake drum or brake disc that rotates with the wheel. The friction lining and friction blocks bear external pressure to generate friction, thereby slowing down the vehicle. Automotive brake pads generally consist of a steel plate, an adhesive heat insulation layer, and a friction block. The steel plate is coated to prevent rust, and the coating process is monitored using an SMT-4 oven temperature tracker to ensure the temperature distribution during coating meets quality standards.

5

3

Share

When parking, should you press the clutch or brake first?

First press the clutch, then the brake. There are two situations when parking, as detailed below: 1. Pulling over to park: When pulling over to park, the speed is generally slow. Turn on the turn signal, observe the traffic on both sides through the turn signal, and drive to the side when safety is ensured. Once the distance between the vehicle and the curb is adjusted, press the clutch, then the brake. Following these steps ensures a smooth stop. 2. Stopping at a traffic light intersection: When approaching a traffic light intersection, decide whether to press the brake or clutch based on the distance to the intersection. If the distance is not too far, you can release the accelerator and use the transmission to slow down. If the speed is relatively fast, press the brake to decelerate. Upon reaching the intersection, first press the clutch, then the brake. After the vehicle comes to a complete stop, shift to neutral, engage the handbrake, and release the clutch and brake.

1

3

Share

What is the normal oil pressure at idle?

For most car engines, the normal oil pressure range is between 2.5 to 3.5 units of pressure. At idle, the pressure should be around 2 to 2.5 units. Both excessively high and low pressures can be very harmful. Effects of oil pressure levels: If the engine oil pressure is too high, it can lead to increased fuel consumption. High-viscosity lubricants have greater viscosity, which increases the frictional resistance between mechanical components, leading to greater power loss and higher fuel consumption. It can also affect heat dissipation; higher viscosity lubricants circulate more slowly, reducing the rate at which heat is carried away, which can cause the engine to overheat. At the same time, insufficient oil volume can reduce the oil pump's output or prevent it from pumping oil due to air intake, which may also result in lower oil pressure. If the oil pressure is too low, it can compromise the engine's lubrication standards, leading to poor lubrication, cooling, and cleaning, which can cause parts to stick and become damaged. Excessive clearance between the crankshaft journal and bearings, low kinematic viscosity, or a damaged filter element can all result in low oil pressure. Functions of car engine oil: Reducing friction and high temperatures: A sufficiently thick oil film separates the surfaces of sliding parts, thereby reducing wear. Sealing: Oil can form a seal between the piston rings and the piston, reducing gas leakage and preventing contaminants from entering. Rust prevention: Lubricating oil adheres to part surfaces, preventing contact with water, air, acidic substances, and harmful gases. Cushioning: When pressure in the engine cylinder rises sharply, suddenly increasing the load on the piston, piston skirt, connecting rod, and crankshaft bearings, the lubricated transmission through the bearings helps cushion the impact load. Cleaning: Good-quality oil can carry carbon deposits, sludge, and worn metal particles from engine parts back to the oil pan. The flow of the lubricant washes away dirt generated on the working surfaces of the parts.

19

1

Share

Identification and Evaluation of Used Accident Vehicles?

Identification of used accident vehicles: 1. Look: The so-called "look" refers to checking whether the vehicle's appearance is abnormal. Mainly observe the paint and edge seams to see if they are intact. If the paint has been redone, it indicates the vehicle was once involved in a collision and repaired. The edge seams can also reveal if the vehicle has been in an accident, as vehicles are generally assembled from 13 panels. When a vehicle rolls off the production line, the gaps between these panels are uniform and consistent, appearing aesthetically pleasing. However, if the vehicle has been impacted, the edge seams may show wrinkles or breaks. Therefore, the first step is to walk around the vehicle and carefully inspect the paint and edge seams to preliminarily determine if it is a used accident vehicle. 2. Smell: The quickest method is to "smell" for any odors inside the vehicle, such as paint or other unusual smells. If you can detect a paint smell, it suggests the vehicle has been repainted. 3. Ask: Before purchasing, it is advisable to consult a professional who can use specialized computer equipment to check the actual mileage of the vehicle. Additionally, review the vehicle's insurance policy to see the cost of compulsory traffic insurance and the year it was purchased. If the compulsory traffic insurance is expensive, it may indicate past accidents. If possible, visit a 4S shop, the vehicle management office, or the insurance company to check for maintenance or accident records. 4. Touch: The so-called "touch" involves manually inspecting various parts of the vehicle. Open the doors and pull down the original factory sealing strips. The door frame and pillars should be straight, with special attention to the original factory weld points at the junctions of the A, B, and C pillars with the vehicle body. These weld points should be slightly rounded and slightly recessed, with lines extending from the roof to the threshold being straight and naturally curved. If you notice abnormal door operation, loose sealing strips, or rough weld points, it is certain the used vehicle has issues. Also, open the engine hood and use your fingers to feel if the edges are naturally straight, smooth, and not rough, indicating one-piece molding. Inspect the vehicle's chassis; the front longitudinal beams (frame) should not show wrinkles or deformation marks.

13

4

Share

What to Do When the Starter Motor Clicks but Doesn't Turn?

This situation may be caused by a damaged battery or a circuit malfunction. The battery is a crucial component of a car. Without it, the vehicle cannot operate normally. When the engine is not running, the battery supplies power to all electronic devices in the car and is also responsible for starting the engine. Common car faults include: 1. Poor idle operation; symptoms may include unstable idling with engine shaking, idle speed exceeding the upper limit, idle speed falling below the lower limit, or rough idling. These issues may be related to faulty or malfunctioning components such as fuel injectors, oxygen sensors, air flow sensors, exhaust gas recirculation valves, as well as poor connections in control circuits or vacuum lines. 2. Abnormal noises; such as "backfire," "popping," "surging," "knocking," and mechanical noises. "Backfire" occurs when combustion flames spray out from the intake pipe in the opposite direction of intake, accompanied by noise. Possible causes of "backfire" include clogged or stuck main fuel injectors or cold start injectors leading to an overly lean mixture, delayed or misfired ignition, unsealed intake valves, intake manifold leaks, or low or fluctuating fuel pressure.

11

2

Share

Which Lynk & Co 02 model is equipped with a four-cylinder engine?

What are the methods to alleviate fatigued driving?

How is the quality of Xinyi brake pads?

When parking, should you press the clutch or brake first?

What is the normal oil pressure at idle?

Identification and Evaluation of Used Accident Vehicles?

What to Do When the Starter Motor Clicks but Doesn't Turn?

Are the Standards for New Energy Vehicle Charging Piles Unified?

What Are the Car Beauty Service Items?

What is coasting in neutral?

Is the Vios Engine Imported?