Which letter indicates the maximum speed of a tire?

What gear should be engaged when parking on a downhill slope?

When parking on a downhill slope, engage the reverse gear before turning off the engine to prevent the car from rolling forward. For parking on level ground, first shift to neutral, apply the handbrake, and then turn off the engine. Engaging a gear utilizes engine braking, where the wheels are connected to the engine crankshaft through gears, so wheel rotation will inevitably drive the engine. The reverse gear, fully known as the reverse driving gear, is one of the three standard gears in a car. It is marked as "R" on the gear console and is designed to allow the vehicle to move backward, serving as a special driving gear. Precautions for reversing on a downhill slope include: 1. Ensure the vehicle is completely stopped before engaging reverse gear; 2. Press the clutch pedal all the way down when shifting to reverse; 3. Maintain slow speed during reversing and avoid pressing the accelerator.

5

1

Share

How to Remove Asphalt Stuck on Tires?

The methods to remove asphalt stuck on tires are: 1. Spray a dedicated asphalt cleaner on the tire, and after the asphalt softens, use a small shovel to remove it, or repeatedly wipe it with a cloth; 2. Use boiling water by pouring it over the asphalt and then scrubbing repeatedly with a brush; 3. Wash the tire with soapy water and scrub repeatedly with a brush; 4. If the asphalt has been compacted over time and adheres to the tread patterns, it needs to be handled at an auto repair shop. The methods for maintaining tires include checking the tire pressure, which can be judged based on the standards in the car maintenance manual, and promptly removing any stones or foreign objects in the tires.

10

1

Share

Which One is the Clutch Pedal?

The clutch pedal is the first stepping point from left to right in the driver's cabin. It serves as the control device for the clutch assembly in manual transmission vehicles. Its primary function is to engage and disengage the clutch between the engine and the transmission through proper operation by the driver. The clutch consists of friction plates, spring plates, a pressure plate, and a power output shaft. When starting the vehicle, the correct operation method for the clutch is to press down the pedal, engage the gear, then lift the clutch pedal until the friction plates begin to make contact. At this point, the foot should pause briefly while simultaneously applying throttle. Once the clutch plates are fully engaged, the clutch pedal can be completely released.

6

5

Share

What is the difference between AT and Tiptronic?

The differences between AT and Tiptronic are: 1. Different modes: AT is an automatic transmission without a manual mode; Tiptronic has both manual and automatic modes. 2. Different practical technologies: AT can only let the computer choose the shift timing, not the driver; Tiptronic allows the driver to choose the shift timing in manual mode. 3. Different structures: AT is a hydraulic automatic transmission; Tiptronic transmission mainly consists of an ordinary gearbox, an electronically controlled clutch, an automatic shift control mechanism, and an electronic control part. AT stands for automatic transmission, also known as automatic gear. Tiptronic cars are a new type of gear shifting method that combines manual and automatic shifting.

20

4

Share

How to Fix Engine Cylinder Pressure Problems?

Engine cylinder pressure problems can be repaired by: 1. Using a cylinder pressure gauge to check the pressure of individual cylinders and recording the data to determine the cause of insufficient pressure; 2. Disassembling the engine to replace the piston rings (compression rings and oil rings) that are not providing adequate pressure. Insufficient cylinder pressure can lead to excessive carbon buildup, severe engine shaking, increased fuel consumption, engine overheating, and difficulty starting the car. The causes of insufficient cylinder pressure include: 1. Piston ring misalignment or excessive wear due to insufficient lubrication; 2. Poor sealing or damage to the cylinder head gasket; 3. Excessive flatness deviation between the cylinder head and cylinder block surfaces, leading to poor sealing; 4. Incomplete closure of intake and exhaust valves; 5. Malfunction in the car's cooling system, resulting in insufficient engine cooling.

17

1

Share

Why does the reverse gear sometimes fail to engage?

The reasons why the reverse gear sometimes fails to engage include: 1. The car is out of fuel; 2. The battery is dead; 3. Incorrect gear position; 4. Fuel quality issues; 5. No antifreeze added; 6. Malfunction of the P-gear lock solenoid valve; 7. Internal failure of the gearshift lever assembly; 8. Incomplete clutch disengagement or failure to press the clutch. The method to engage the reverse gear is to press the clutch and push the gear lever downward to the R mark, then lift it upward to successfully engage the gear. For automatic transmission vehicles, the gear lever needs to be lifted towards the driver's body before it can be shifted clockwise, pulling it down one notch at a time to R to successfully engage the gear. The full name of the reverse gear is the reverse driving gear, designed to allow the vehicle to move backward, and it is a special type of driving gear.

11

5

Share

Which letter indicates the maximum speed of a tire?

What gear should be engaged when parking on a downhill slope?

How to Remove Asphalt Stuck on Tires?

Which One is the Clutch Pedal?

What is the difference between AT and Tiptronic?

How to Fix Engine Cylinder Pressure Problems?

Why does the reverse gear sometimes fail to engage?

How to Repair Wheel Rims?

What is the correct method to start an automatic transmission car?

How to Press the Clutch When Shifting Gears?

How to Deal with Spark Plugs Soaked in Engine Oil?