Which lane to turn into when turning left?

1 Answers
LeAva
07/29/25 6:17pm
After turning left, enter the leftmost lane in the east-west direction. Below is relevant information about traffic regulations: Maintain a safe speed: When driving on the road, motor vehicles must not exceed the maximum speed indicated by speed limit signs. On road sections without speed limit signs, a safe speed should be maintained. Follow traffic signals: When passing through intersections, motor vehicles should proceed according to traffic signals, signs, markings, or the direction of traffic police. When passing through intersections without traffic signals, signs, markings, or traffic police direction, vehicles should slow down and yield to pedestrians and vehicles with the right of way.
Was this review help?
12
1
Share
More Forum Discussions

At what speed should you shift gears in a manual transmission?

Manual transmission vehicles' gear speeds at idle are generally determined by the engine's idle speed and the transmission's gear ratio, which varies by model. First gear: 10 km/h; Second gear: 10-30 km/h; Third gear: 30-40 km/h; Fourth gear: 40-60 km/h; Fifth gear: 60-120 km/h. Below are some tips for shifting gears in a manual transmission car: 1. Master the clutch pedal operation through practice, ensuring smooth and steady movements. Develop a good habit of pressing it all the way down and releasing it slowly. 2. Coordinate the throttle and clutch. When starting, engage first gear, slowly release the clutch, and apply throttle at the half-clutch point. Only fully release the clutch once the car begins to move. 3. Make gear shifts smooth and continuous. Press the clutch all the way down and shift gears in one decisive motion.
13
2
Share

Release the Clutch First or the Brake First?

After completing preparatory tasks such as adjusting the seat and rearview mirrors, press the clutch all the way down, shift into neutral, and start the engine. When beginning to move, slowly release the clutch to the semi-engaged position. Once the vehicle gains some power (i.e., when there is a slight vibration), then release the brake. 1. Foot Brake Start: While keeping the foot brake pressed, depress the clutch, shift into first gear, and release the clutch to the semi-engaged position. When the body shows slight vibration and the front of the car lifts slightly, release the foot brake, and the vehicle will start moving slowly forward. 2. Hand Brake Start: When using the hand brake, there is no need to press the foot brake. This method is used on slopes to stabilize the parked vehicle by pulling the hand brake. The specific steps are: hold the steering wheel firmly with the left hand, depress the clutch, shift into first gear, place the right hand on the hand brake, release the clutch to the semi-engaged point, and immediately release the hand brake to allow the vehicle to move forward smoothly.
7
1
Share

Can an automatic transmission car start in P gear?

An automatic transmission car can start in P gear. In fact, the transmission of an automatic car is not that fragile, and it can be started in either P gear or N gear. More information about P gear is as follows: 1. P gear is the most common gear in automatic transmission models, usually located at the frontmost position of the gearshift console, in front of the R gear, designed to lock the axle when the car is stationary on a slope. 2. Both P gear and N gear are neutral gears. The power generated by the engine input cannot be transmitted to the transmission output, which is why drivers often experience a slight slide after parking in P gear on uneven roads. 3. Since P gear is equipped with an additional mechanical braking device, the vehicle will not move once the gear grooves in the transmission are locked by the pawl.
12
4
Share

Has the CR-V Engine Oil Dilution Issue Been Resolved?

Currently, the CR-V engine oil dilution issue has been resolved, but a very small number of owners still report experiencing this problem. It remains difficult to determine whether this is a common issue. More information regarding engine oil dilution is as follows: 1. The engine injects a large amount of gasoline during startup. Sometimes, due to excessive injection and incomplete combustion, the excessive pressure on the cylinder walls forces gasoline into the crankcase. 2. Normally, gasoline evaporates once the engine reaches operating temperature. However, during frequent cold starts and in cold weather, the engine oil temperature may not rise sufficiently, making it difficult for the gasoline to evaporate, which leads to the issue of continuously increasing engine oil levels.
16
1
Share

Can the engine cover be removed?

The engine cover should not be removed. Generally, the engine cover of a car not only serves as a simple decoration but also protects the engine components from natural elements like rain and snow, ensuring they remain in good working condition. Additionally, it prevents debris from falling into the engine, which could affect its normal operation. Moreover, during vehicle operation, the cover helps reduce wind resistance, improve fuel efficiency, and enhance acceleration. Here are some details about the engine cover: 1. The engine cover is typically composed of an outer and inner panel with heat insulation material in between. The inner panel enhances rigidity, and its geometric shape is designed by the manufacturer, usually in a skeletal form. 2. The engine cover can beautify the engine compartment, provide some degree of dust protection, and also help in noise reduction.
12
1
Share

What are the main components of an automobile starting system?

Starting an engine refers to the entire process of transitioning the engine from a stationary state to an operational state. The system required to complete this process is called the starting system. Its function is to drive the engine crankshaft to rotate until the engine can continue operating under its own power. Information about the automobile starting system is as follows: 1. The starting system consists of a starter, a solenoid switch (starting relay or solenoid coil), and a starting switch (or start button). 2. The starter mainly comprises an armature assembly, a solenoid switch, a housing assembly, a rear cover (drive end cover), and a front cover (brush end cover). It uses the battery as the starting power source, driven by a DC motor, and provides starting torque to the engine flywheel crankshaft assembly through the transmission mechanism and control mechanism, enabling the engine to enter normal operating conditions.
15
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.