Which Lane to Enter After a Left Turn?

1 Answers
SanJoel
07/29/25 5:28pm
After making a left turn with three lanes available, the vehicle should enter the leftmost lane. Here are the relevant details: 1. Legal Provisions: According to the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China," when a motor vehicle passes through an intersection controlled by traffic signals, it shall proceed as follows: at intersections with designated lanes, enter the appropriate lane based on the intended direction of travel; vehicles preparing to enter a roundabout must yield to vehicles already within the intersection; when turning left, the turn should be made to the left of the intersection's center point. Turn signals must be activated during the turn, and low beam headlights should be used when driving at night. 2. Left Turn Waiting Zone: The left turn waiting zone is exclusively for vehicles making a left turn. When the traffic light for straight-moving vehicles in the same direction is green, even if the left turn signal is red, vehicles intending to turn left are permitted to enter the "left turn waiting zone" at the intersection and wait until the left turn signal turns green before proceeding through the intersection.
Was this review help?
11
1
Share
More Forum Discussions

What causes the abnormal noise when shifting to P gear while driving?

The reasons and solutions for abnormal noise when shifting to P gear are as follows: 1. According to the structural design of automatic transmissions, this sound is considered normal. The P gear is designed as a parking gear, and its principle involves a brake pawl engaging with a ring gear. As long as the ring gear is in gear, this P gear locking mechanism is caused by the interaction between the gear on the internal output shaft of the transmission and the locking pin. This is why the vehicle cannot move forward or backward when shifted to P gear, with the force appropriately increasing on steeper slopes. 2. For this situation, it is recommended to first bring the vehicle to a complete stop, engage the manual brake (handbrake), and then shift to P gear for better results. Additionally, it is advisable to check the performance of the engine pawl, as degraded performance may lead to the aforementioned phenomenon.
1
5
Share

How much windshield washer fluid should be added to an Audi A4?

Audi A4 generally requires about 4 liters of windshield washer fluid. There is a dipstick in the washer fluid reservoir; you can add the fluid while checking the level, and stop when it reaches the marked line. Adding too much may cause overflow and unnecessary waste. During autumn and winter, the windshield washer fluid should have excellent cleaning and antifreeze performance. The steps to add windshield washer fluid to an Audi A4 are as follows: 1. Use the wiper control knob to spray out the old washer fluid first. 2. After the old fluid is completely sprayed out, open the washer fluid filler port and add a small amount of new washer fluid solution. 3. Turn on the washer fluid spray switch again to clean out any remaining old fluid. 4. When no more fluid comes out from the spray nozzle the second time, add about 4L of new washer fluid, then close the cap securely.
15
1
Share

What is the steering wheel technique for the curve driving in Subject 2?

There are mainly 5 techniques for the steering wheel operation in the curve driving of Subject 2, which are as follows: 1. When the vehicle is about to enter the S-curve, remember to align the car body straight and pay attention to the position of the front of the car, driving the car towards the middle of the road. 2. When the edge of the left engine cover coincides with the yellow line on the road surface, turn the steering wheel one full turn to the left, completing the first curve. 3. Drive along the edge line and make timely corrections if there is any deviation. 4. After completing the first curve, straighten the car body and continue driving along the yellow line on the ground, remembering not to cross the line and always stay observant. 5. After passing the curve, remember to straighten the car body and drive out.
10
0
Share

How many cylinders does the Volvo XC90 engine have?

Volvo XC90 is a four-cylinder, which is a mid-to-large luxury SUV under Volvo. This model uses two types of engines in total, one is a 2.0-liter turbocharged engine, and the other is a 2.0-liter twin-charged engine. The twin-charged engine features both a supercharger and a turbocharger. The twin-charged engine can use different charging methods under different operating conditions, making this engine more efficient and powerful. More details are as follows: 1. Volvo XC90's 2.0-liter turbocharged engine has 254 horsepower and a maximum torque of 350 Nm. This engine is paired with an 8AT transmission. 2. The 2.0-liter twin-charged engine has 320 horsepower and a maximum torque of 400 Nm. This engine can output maximum torque at 2200 rpm and sustain it up to 5400 rpm. This engine is also paired with an 8AT transmission. 3. The front suspension of the Volvo XC90 uses a double-wishbone independent suspension, while the rear suspension uses a multi-link independent suspension. The double-wishbone independent suspension can enhance the wheel's ground contact performance, thereby improving the wheel's grip. Improved grip enhances the vehicle's handling. 4. The Volvo XC90 is equipped with a full-time four-wheel-drive system across all models and uses a multi-plate clutch central differential. Vehicles with a full-time four-wheel-drive system are always in four-wheel drive. The full-time four-wheel-drive system can improve the mechanical grip of the wheels. Enhanced grip improves the vehicle's handling and driving stability.
7
4
Share

What are the differences between Dongfeng Honda and Guangqi Honda?

Although both Guangqi Honda Automobile Co., Ltd. and Dongfeng Honda Automobile Co., Ltd. are subsidiaries of Honda, the differences between them mainly lie in their joint ventures, vehicle models, and scale. Both companies have their own popular models that are favored by many consumers. Here are the specific differences between the two: 1. Different joint ventures. Guangqi Honda Automobile Co., Ltd. (formerly Guangzhou Honda Automobile Co., Ltd.; referred to as Guangqi Honda) was established on July 1, 1998. It is a joint venture formed by Guangzhou Automobile Group Co., Ltd. and Honda Motor Co., Ltd., with each party holding a 50% stake. The cooperation period is 30 years. Dongfeng Honda Automobile Co., Ltd. is a vehicle manufacturing and sales enterprise jointly established by Dongfeng Motor Group Co., Ltd. (50% stake), Honda Motor (China) Investment Co., Ltd. (10% stake), and Honda Motor Co., Ltd. (40% stake). 2. Different vehicle models. Guangqi Honda currently produces seven major series with over 30 models, including the Crown series SUVs, Accord series sedans, Odyssey multi-purpose series sedans, Lingpai series sedans, City series sedans, Fit series sedans, and the self-owned brand Everus series sedans. Since its establishment, Dongfeng Honda has successively introduced Honda SUVs such as the CR-V, Civic, Spirior, CIIMO, Elysion, Insight, and Jade. 3. Different scales. Guangqi Honda currently has two production bases: Huangpu Plant and Zengcheng Plant, with a combined annual production capacity of 480,000 vehicles and a total area of 1.6 million square meters. Guangqi Honda has over 8,000 employees. Dongfeng Honda's first plant covers an area of 1.81 million square meters and includes a research and development center as well as nine production lines for stamping, welding, resin molding, painting, engine casting, machining, engine assembly, and vehicle assembly. The second plant covers an area of 1.05 million square meters and includes seven production lines for stamping, welding, painting, resin molding, engine assembly, vehicle assembly, and vehicle inspection. According to the plan, the second plant initially has an annual capacity of 100,000 vehicles and will gradually expand production capacity, eventually reaching an annual capacity of 240,000 vehicles. Currently, it mainly produces the GREIZ, XR-V, and JADE models.
20
4
Share

Is it possible to have a vehicle inspected in a different location? What procedures are required?

It is possible to have a vehicle inspected in a different location. The required procedures for an out-of-area vehicle inspection are as follows: original ID card, vehicle license, copy of compulsory traffic insurance, and proof of vehicle and vessel tax—these four documents are sufficient. The documents required for an out-of-area vehicle inspection include the vehicle registration certificate or the vehicle license, and the agent must present the original ID card. To apply for an out-of-area vehicle inspection, you need to go to the vehicle management office branch corresponding to the address recorded in the identity document of the vehicle owner (for corporate entities, the organization code certificate is required). After the vehicle passes the inspection at the designated location, the vehicle owner (or agent) should fill out an application form and present the vehicle license and the compulsory traffic insurance certificate.
10
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.