Which Lane Should You Turn Into When Making a Right Turn?

2 Answers
DelAllie
07/29/25 12:49am
When making a right turn, vehicles should generally enter the rightmost motor vehicle lane, accelerate, and then proceed according to the designated lane. Apply force with the left hand to make a tight turn into the first lane on the right. This practice helps avoid collisions with vehicles going straight. The rules for right turns also depend on the traffic signals at the intersection: If the intersection only has circular red, yellow, and green traffic lights, you can make a right turn directly. If the intersection has arrow signal lights, you must follow the arrow signal's instructions. A red right-turn arrow means you cannot turn right; when the right-turn arrow light turns off or changes to green, you can proceed with the turn. If a traffic officer is directing traffic, follow their instructions for turning. Precautions for right turns: Before turning right, activate the right turn signal to alert others behind you. Check the right-side mirror for any obstacles or pedestrians that may affect your turn. Just before turning, check the right-side mirror again for any potential hazards.
Was this review help?
10
2
Share
AlejandroRose
08/12/25 5:01am
When I was learning to drive, my instructor emphasized that after making a right turn, I should merge into the far-right lane to avoid conflicts with through traffic and maximize safety. Once, in a hurry to get home, I turned into the middle lane at an intersection and almost collided with a through vehicle—that was a profound lesson. Since then, every time I make a right turn, I slow down in advance, check the rearview mirror for any sudden appearances of bicycles or pedestrians, and only proceed into the right lane after confirming it's clear. In urban areas with complex road conditions and multiple lanes, extra caution is necessary. If I need to change lanes to the left after entering the right lane, I always remember to signal and wait for a safe opportunity. Developing this good habit reduces the risk of accidents and makes driving more reassuring. Safety comes first—don’t cut corners by ignoring the rules.
Was this review help?
7
2
Share
Expand All
More Forum Discussions

Do I Need to Change the Transmission Fluid When Replacing the Clutch Three-Piece Set?

Yes, you need to change the transmission fluid. When replacing the clutch three-piece set, the transmission must be removed from the vehicle, and the half-shafts on both sides of the transmission must be taken off. When the half-shafts are removed, the gear oil in the transmission will flow out. Below is an introduction to the automotive transmission: 1. Transmission: A device that changes the speed ratio and direction of motion. It is used in automobiles, tractors, ships, machine tools, and various machines to alter the torque, speed, and direction of motion transmitted from the driving shaft to the driven shaft under different working conditions. A gear-driven transmission generally consists of a housing and several pairs of gears. 2. Definition: The transmission is a gearbox that changes the transmission ratio and direction of motion. It is located between the clutch and the central drive. Its main functions are: changing the driving force and speed of the vehicle (shifting gears) when the engine speed and torque remain unchanged; allowing the vehicle to reverse (changing direction); and enabling the engine to stop without stalling (neutral gear).
20
1
Share

What is the wading depth of the Camry?

The Camry can handle wading depths of around half a meter without issues. Key operating points and precautions for wading with the Camry: 1. When wading: Ensure the engine is running normally, and the steering and braking systems are responsive and reliable. Engage a low gear and drive smoothly into the water, avoiding excessive throttle or sudden acceleration to prevent water splashing into the engine and causing it to stall. 2. While driving: Maintain steady throttle to provide the Camry with sufficient and stable power, aiming to pass through in one go. Avoid stopping, shifting gears, or making sharp turns midway, especially when the underwater surface is sandy or muddy. 3. If encountering quicksand or the Camry's wheels spinning without traction: Stop immediately. Do not force the vehicle forward or backward, and avoid pressing the throttle pedal aggressively with the clutch partially engaged. Keep the engine running and organize manpower or other vehicles to push or tow the car out to prevent sinking deeper.
12
2
Share

What type of suspension does the Great Wall C30 NEV use?

The Great Wall C30 NEV uses a MacPherson independent suspension at the front and a torsion beam non-independent suspension at the rear. Below is an introduction to the MacPherson independent suspension and torsion beam non-independent suspension: 1. The most common non-independent suspension in cars is the torsion beam suspension. This type of suspension has a simple structure, small size, occupies little space, and is relatively low-cost. 2. Many compact cars and small cars use torsion beam suspensions. This is not only to reduce costs but also because many small and compact cars do not have enough space at the rear to install a multi-link independent suspension. Using a torsion beam suspension can also increase rear passenger space and trunk space. 3. The MacPherson suspension is the most widely used suspension, with a relatively simple structure. The MacPherson suspension has only one L-shaped control arm and hardly occupies any engine compartment space. Many cars with front-mounted transverse engines use MacPherson suspensions, which are also relatively low-cost.
11
5
Share

What are the requirements for self-training a driver's license?

The prerequisite for self-training a driver's license is that the applicant must have previously obtained a driver's license. For example, if the license was canceled due to failure to renew it for two years because of going abroad or forgetting, or if the license was revoked by traffic authorities due to reasons such as traffic accidents or drunk driving, but after a certain period, the law allows reapplying for a license. These individuals can directly apply for the exam at the vehicle management office without going through a driving school. Related information about obtaining a driver's license: 1. Requirements: Individuals who meet the driving license conditions stipulated by China's public security department and wish to obtain a motor vehicle driver's license must first undergo driver training and then pass the examination conducted by the traffic management department of the public security authority. Only after passing the exam can they obtain a motor vehicle driver's license. 2. Content: The motor vehicle driver's license examination is divided into subjects covering road traffic safety laws, regulations, and related knowledge, field driving skills, and road driving skills along with safe and civilized driving knowledge. The examination content and passing standards are uniform nationwide, with corresponding test items specified according to different types of vehicles eligible for driving.
1
5
Share

What Type of Engine Oil is Suitable for the Lynk & Co 03?

The Lynk & Co 03 uses fully synthetic engine oil with a 0W-20 viscosity grade. This is because the Lynk & Co 03 is equipped with either a 1.5T or 2.0T turbocharged engine, which requires higher-performance oil for optimal engine protection. Fully synthetic oil offers superior fluidity and lubricity compared to other types of engine oils, thereby providing better protection for the engine. Below is an introduction to engine oil: 1. There are three types of engine oils used in vehicles: mineral oil, fully synthetic oil, and semi-synthetic oil. Among these, fully synthetic oil performs the best, as it can adapt to a wider range of temperatures and has a longer service life. 2. Under the same operating conditions, fully synthetic oil can protect the engine effectively even at lower viscosity levels. 3. The service life of mineral oil is approximately 5,000 kilometers, semi-synthetic oil around 6,500 kilometers, and fully synthetic oil about 10,000 kilometers. Different service intervals result in varying levels of performance and protection.
19
1
Share

Is the impact significant when the car is pushed while in P gear?

One or two pushes won't have much impact. The function of the P gear is to lock the transmission gears when parking, where a locking block engages with the transmission gears to prevent wheel movement. Pushing the car might cause the locking block to disengage, but generally, one or two instances won't cause any issues. Here is some additional information: 1. P gear: Parking gear, used when the engine is off or the car is stationary. P (Parking) is used for parking purposes, employing a mechanical device to lock the rotating parts of the car, preventing it from moving. When the car needs to remain stationary for an extended period or before leaving the vehicle after parking, the handbrake should be engaged, and the gear lever should be moved to the "P" position. 2. Precautions: The P gear should only be used when the vehicle is completely stopped; otherwise, the mechanical parts of the automatic transmission may be damaged. Additionally, automatic transmission vehicles are equipped with a neutral start switch, ensuring the engine can only be started in "P" or "N" gear to prevent sudden forward movement if started accidentally in other gears.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.