Which is more harmful, a flood-damaged car or an accident-damaged car?

1 Answers
ElisaDella
07/29/25 5:49pm
Compared to accident-damaged cars, flood-damaged cars pose greater hazards. Here are methods to identify flood-damaged cars: Smell the interior odor: Check if there's a musty smell inside the car. Flood-damaged vehicles often have musty odors in hidden areas like floor mats, trunk liners, and under seats, which are difficult to clean thoroughly and usually leave evidence. Be cautious if you detect a musty smell, and also be wary if the car smells unusually fragrant, as this might be an attempt to mask the musty odor. Inspect hidden parts of the vehicle: Look for rust or signs of screw removal/replacement in concealed areas; pull out the seats to check for rust or sand in the tracks; extend the seatbelt fully to check for water stains or dirt at the end.
Was this review help?
4
3
Share
More Forum Discussions

How to Adjust the Heater in the Mazda3 Axela?

After starting the Mazda3 Axela, wait approximately 5-10 minutes for the engine coolant temperature to reach normal operating levels. At this point, you can activate the vehicle's heating system. Adjust the Mazda3 Axela's air conditioning system to recirculation mode, then turn the temperature control knob to the heating setting (indicated by the red zone) to begin warm air output. Below is an introduction to automotive air conditioning functions: 1. The air conditioning system regulates cabin temperature by both heating and cooling the air to maintain a comfortable environment. 2. It removes humidity from the air. Dry air helps absorb perspiration, creating a more comfortable atmosphere. 3. The system can intake fresh air, providing ventilation capabilities. 4. It filters the air, removing dust and pollen particles.
6
2
Share

How to Turn Off the Electrical Consumption Display on Audi?

Audi's onboard computer displays three types of fuel consumption readings, which can be adjusted or turned off using the knob on the left side of the steering wheel. Here are some tips to reduce fuel consumption: 1: Increase tire pressure to reduce friction. 2: Clean out the trunk to reduce weight. 3: Avoid driving in the city or suburbs. 4: Drive during peak traffic hours if possible; it's better to be stuck in traffic than to take detours. 5: Avoid having the car fully occupied. 6: Do not fill the fuel tank to the brim. 7: Try to avoid using the air conditioning. 8: It's recommended to refuel at night when temperatures are lower, as you can get more fuel. 9: Use neutral gear and coasting appropriately.
13
0
Share

Can You Drive with a Leaking Half Shaft Oil Seal?

You can still drive with a leaking half shaft oil seal, but it needs to be replaced promptly. A leaking half shaft oil seal has the following hazards: 1. The main hazard of oil leakage is the loss of oil, leading to waste. In severe cases, it may cause insufficient oil, which can damage the engine. This damage is not directly caused by the oil leakage but by the resulting insufficient oil pressure. Therefore, it's essential to monitor the oil level closely. 2. Most vehicles have an oil level display to prevent driving with oil below the normal level unknowingly. Additionally, an alarm light will indicate insufficient oil pressure, so regular checks are necessary. 3. Transmission oil leakage can lead to insufficient lubrication, accelerating friction between gears. Thus, when disassembling, it's important to check for gear wear and replace shift gears based on their wear condition. Oil leaks must be repaired.
15
2
Share

Where is the Golf 7 fuse box located?

There are two fuse boxes in the Golf 7. One fuse box is located under the dashboard in the driver's compartment, specifically on the left side of the center console, inside the cover above the driver's footwell. The other fuse box is near the battery in the engine compartment. Each fuse box is similar, with corresponding numbers and descriptions on the inside of the cover, allowing car owners to clearly identify the specific information of each component. Below is related information about fuses: Steps to replace a fuse: 1. Turn off the vehicle and all power sources before inspection. 2. Locate the corresponding position, use a small pry tool to open the protective cover, and check the component information inside the fuse box. 3. Use a light or a test pen to perform a preliminary check on the fuse, confirming it has blown before considering replacement. 4. The new fuse should match the old one in size, color, and all specifications. 5. After replacement, check if the corresponding component is functioning; otherwise, send it to a repair shop promptly. Fuse-related precautions: 1. Using fuses that do not meet specifications may cause fires or injuries. 2. Installing fuses with a current rating higher than specified can easily overload and damage components. 3. Never attempt to repair a damaged fuse. 4. Do not use paper clips as substitutes for original fuses.
18
1
Share

What does MIC mean in a car?

MIC in a car stands for microphone, which is the abbreviation of Microphone. Inside the car, the microphone is mainly used for Bluetooth call answering and navigation voice playback, among other functions. Wireless microphones can generally be divided into three frequency bands: FM band, VHF band, and UHF band. The relevant introductions are as follows: 1. FM band: Since FM radios operate at frequencies between 88-108MHz, and wireless microphones in the FM band have frequencies higher than 108MHz, usually between 110-120MHz, FM radio signals do not interfere with FM band wireless microphones. This type of wireless microphone has a simple structure and low cost, but the sound quality is relatively poor. 2. VHF band: The VHF band is generally referred to as the V band, with frequencies between 180-280MHz. Due to the higher frequency, it receives less interference and uses crystal frequency locking, resulting in more stable reception performance. 3. UHF band: The UHF band is generally referred to as the U band, with frequencies between 700-900MHz. At such high frequencies, there is almost no interference from other external frequencies. Additionally, U band microphones often use surface-mount components, offering very stable performance and good sound quality.
18
1
Share

How many times do you need to press to turn off the power of a Mercedes-Benz?

Before turning off the power, shift to neutral first. Then press the one-touch start button once, and the engine will shut down immediately. Open and then close the driver's door, and the power will be cut off. Part of the smart car is the one-touch start device, which is a button that simplifies the ignition process. Below is a related introduction to the Mercedes-Benz shutdown steps: 1. Press the brake pedal to stop the vehicle smoothly. 2. Shift the gear from D to N. 3. Tighten the handbrake. 4. Release the foot brake, but do not turn off the power. 5. Continue to press the foot brake and shift the gear from N to P. 6. Release the foot brake, press the one-touch start button, the power will be turned off, and the shutdown is completed.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.