Which Fit models comply with China's National VI emission standards?

What is the speed requirement for downshifting from second gear to first gear?

Speed should be controlled around 15-20km/h. Downshifting must be done gear by gear. Below is the relevant explanation: Principle: When driving at high speeds, the transmission gears rotate with the engine. During movement at high speeds, the engine RPM is relatively low while the transmission RPM is high. When downshifting, if the engine RPM is insufficient while the transmission RPM is too high, gear grinding noise will occur. Therefore, the lower gear cannot be engaged during downshifting unless the throttle is blipped to increase engine RPM to match the transmission speed. Exam practice: In the driving test (Subject 3), there are gear shifting operations, and instructors require downshifting to be done gear by gear, meaning sequential downshifting without skipping gears. During the Subject 3 test, skipping gears during downshifting will result in point deductions, potentially causing test failure.

18

0

Share

Where is the handbrake light switch located?

The handbrake light switch is located above the brake pedal, on the master brake cylinder, and above the rear differential. Brake Light Introduction: Generally installed at the rear of the vehicle, the main color of the light is red. This makes it easier for vehicles behind to detect when the front vehicle is braking, helping to prevent rear-end collisions. The principle is that power passes through a fuse to the brake switch. When the brake pedal is pressed, the switch connects, sending electricity to the two brake lights and one high-mounted brake light, completing the circuit through the negative wire connected to the vehicle body. Handbrake Indicator Light: Used to display the status of the vehicle's handbrake, it is usually off. When the handbrake is engaged, the indicator light automatically turns on; when the handbrake is released, the indicator light turns off. Some vehicle models will also emit a warning sound if the handbrake is not released while driving.

18

3

Share

What is the function of a movable pulley?

The function of a movable pulley is to change the direction of force and save effort. In essence, a movable pulley is a lever with a power arm twice as long as the resistance arm (a labor-saving lever). It not only changes the direction of force but can also save up to half the effort, although it does not save work. More information about pulleys is as follows: Introduction: A fixed pulley is a pulley that does not move. Its immobility is not simply about not moving; rather, the central axis of the pulley is fixed. Advantage: The main advantage of a fixed pulley is that it can change the direction of force. When using a fixed pulley to pull a very heavy object, it may not be easy to apply force directly, but a fixed pulley can redirect the force to a more convenient direction, making it easier to move the heavy object.

15

1

Share

What is the braking distance of a car at 40 km/h?

The braking distance at 40 km/h is approximately 5 meters. Factors determining the braking distance of a car: The braking of a car mainly depends on the friction between the tires and the ground. The magnitude of the friction depends on the friction coefficient. The braking distance is directly proportional to the square of the speed and inversely proportional to the friction coefficient. When the friction coefficient is constant, the braking distance depends on the speed. If the speed doubles, the braking distance will increase to four times the original. Safe following distance: There is a principle in safe driving to maintain a following distance, which is to keep the distance as one-thousandth of the speed. For example, at a speed of 50 km/h, maintain a distance of 50 meters; at a speed of 120 km/h, maintain a distance of 120 meters. Comparing with the above calculation results, this distance is very safe. Moreover, when the speed is less than 100 km/h, people have sufficient reaction time.

17

0

Share

Who Owns the Vehicle After It's Declared a Total Loss?

Ownership remains with the vehicle owner. Below is relevant information regarding vehicle scrapping: Required materials for vehicle scrapping: Private vehicles require the owner's ID card; vehicle registration certificate; vehicle license plate; for company vehicles, an organization code certificate with official seal is needed; accident vehicles require supporting documentation. Mandatory scrapping after missing 3 consecutive annual inspections: According to the 'Mandatory Vehicle Scrapping Standards', if a vehicle fails to obtain an inspection compliance mark for 3 consecutive inspection cycles after the inspection validity period expires, it must be mandatorily scrapped. Driving a forcibly scrapped vehicle on the road will result in severe penalties for the driver, including fines and revocation of driving qualifications.

12

5

Share

Do I Need to Go to the DMV After Picking Up the Car?

If the 4S dealership handles the license plate registration, you don't need to go. If you're doing it yourself, you will need to go, but it doesn't have to be on the same day; you can go a few days later. Preparation Before License Plate Registration: Before going to the DMV for license plate registration, you must have the vehicle's certificate of conformity, purchase invoice, and compulsory insurance policy (commercial insurance can be purchased after registration). Before processing the license plate registration at the DMV, you should make three copies each of your ID card, temporary residence permit (if applicable), vehicle certificate of conformity, purchase invoice, and compulsory insurance policy for backup. Paying the Purchase Tax: The purchase tax is paid at the purchase tax collection office. You will need to provide your ID card and a copy, the purchase invoice (tax filing copy), the original certificate of conformity and a copy, the tax declaration form, and for imported vehicles, the customs goods import certificate and a copy, and the commodity inspection certificate and a copy. After Guangzhou implemented the license plate quota system, you also need to print the vehicle purchase eligibility certificate before you can process the purchase tax payment.

6

5

Share

Which Fit models comply with China's National VI emission standards?

What is the speed requirement for downshifting from second gear to first gear?

Where is the handbrake light switch located?

What is the function of a movable pulley?

What is the braking distance of a car at 40 km/h?

Who Owns the Vehicle After It's Declared a Total Loss?

Do I Need to Go to the DMV After Picking Up the Car?

Must the Damage Assessment List and Repair List Be Provided to the Vehicle Owner?

What Problems Can Occur When Water Enters the Engine?

What Causes Engine Noise After Changing Motorcycle Oil?

Should the Air Filter Be Replaced During a Minor Maintenance?