Which country's brand is BYD?

1 Answers
CaliRose
07/30/25 5:51am
BYD is a Chinese car. The following is the relevant content introduction: 1. The logo of BYD is oval in shape and is accompanied by the letters "BYD". The design of the logo highlights BYD's innovation, technology, and the essence of corporate culture. 2. BYD is a Chinese automobile brand, founded in 1995, mainly producing commercial cars, household cars, and batteries. Starting with a scale of more than 20 people, it grew into the world's second-largest rechargeable battery manufacturer in 2003, and in the same year, BYD Auto was established. BYD Auto follows the development route of independent research and development, independent production, and independent brand.
Was this review help?
15
2
Share
More Forum Discussions

Does a Repaired Roof Count as a Salvage Vehicle?

A repaired roof does count as a salvage vehicle. Here are the reasons why a damaged roof affects the vehicle: 1. Traffic accidents: After a collision, whether active or passive, the vehicle's roof will usually suffer some degree of impact, leading to torque or dents and varying degrees of deformation. 2. Rollover accidents: In a rollover, the roof is the most vulnerable part, often resulting in large-scale collapse or severe deformation. 3. Falling objects from heights are most likely to damage the roof: Therefore, when parking, try to avoid spots near buildings to prevent falling objects from damaging the roof.
17
2
Share

What Causes a Dead Mouse Smell Inside the Car?

Check if the air conditioning filter is excessively dirty. If it is, it needs to be replaced. Another possibility is that there might be a dead mouse or other small animal carcass inside the air conditioning ducts. Below are the steps to handle a dead mouse in the car: 1. Inspection: Check if there is a dead mouse inside the car's air conditioning system. If found, remove the mouse first. Then, turn on the air conditioning, clean the air vents, and inspect the intake vents for any other debris. It's also advisable to replace the air conditioning filter, as a dirty filter not only fails to perform its original function but also causes secondary pollution to the air entering the car. To completely eliminate odors in the car, the source must be addressed. 2. Cleaning: Clean the air conditioning ducts, as a dead mouse inside can leave bacteria and cause odors. Use deodorizers or air conditioning duct cleaners to remove odors from the ducts. For external circulation, naturally ventilate the car by spraying the cleaner evenly into the air vents, then open the windows and turn on the air conditioning for ventilation.
12
5
Share

Why was the active grille shutter removed from the x3?

x3 removed the active grille shutter mainly because it could get stuck with debris, causing short circuits during car washing. Here is some extended information about the BMW x3: 1. Body dimensions: The BMW x3 has a length of 4717mm, width of 1891mm, height of 1689mm, and a wheelbase of 2864mm. 2. Powertrain: It is equipped with a 2.0TL4 engine featuring turbocharged intake, delivering a maximum horsepower of 184ps and a maximum torque of 290nm. The transmission is an 8-speed automatic with manual mode, and the top speed is 210 kilometers per hour.
12
0
Share

Should I buy the x3 25i or 28i?

28i is more expensive, with 40ps more power and richer configurations; 25i has sufficient power and lower fuel consumption than 28i, it depends on personal preference. The differences between BMW x3-25i and 28i are: 1. Different power: x325i model uses a low-power version of the 2.0L turbocharged engine; 28i model uses a medium-power version of the 2.0L turbocharged engine. 2. Different tuning: x325i has a maximum power of 135KW, maximum horsepower of 184PS, and maximum torque of 290 Nm; 28i has a maximum power of 165KW, maximum horsepower of 224PS, and maximum torque of 310 Nm.
6
5
Share

What Causes a Car to Auto-Lock Without Turning Off the Engine?

Auto-locking without turning off the engine is caused by a program error in the car. If the car has been modified or had hidden features enabled, the likelihood of program confusion increases. It is recommended to conduct a detailed inspection at an authorized 4S dealership. Below is an introduction to the car's auto-locking function: 1. Introduction: The purpose of the auto-locking function is theft prevention. It allows the car to lock quickly after starting, preventing door-pulling robberies during traffic jams or at red lights, providing a certain level of security. 2. Advantages: It protects passengers, especially children inside the car, preventing young, unaware passengers from opening the door handle while the car is in motion.
1
5
Share

What are the diesel fuel testing indicators?

Here is an introduction to diesel fuel testing indicators: 1. Oxidation stability: Determined according to SH/T0175 method. Method summary: Filter 350mL of sample, inject it into an oxidation tube, pass oxygen at a rate of 50mL/min, and oxidize at 93°C for 16 hours. Then cool the oxidized sample to room temperature and filter to obtain filterable insolubles. 2. Sulfur content: Determined according to GB/T380 method. Method summary: Burn an appropriate amount of sample in a lamp, absorb the generated sulfur dioxide with a 0.3% sodium carbonate aqueous solution, and titrate the absorption solution with 0.05N hydrochloric acid standard solution using bromocresol green methyl red as titration indicator. 3. Acidity: Determined according to GB/T258 method. Method summary: Volumetric method. This method uses boiling ethanol to extract organic acids from light diesel, then titrates while hot with 0.05N potassium hydroxide ethanol solution. The milliliters of potassium hydroxide required to neutralize 100 milliliters of petroleum product is called acidity. 4. Carbon residue: Determined according to GB/T268 method. Method summary: Place an appropriate amount of sample in a crucible for decomposition distillation. The residue undergoes intense heating for cracking and coking reactions. After heating for 30±2 minutes, the carbon residue value is calculated based on the mass of carbonaceous residue. 5. Ash content: Determined according to GB/T508 method. Method summary: Place no more than 100 grams of sample in a pre-weighed crucible, heat on an electric hot plate using an ashless filter paper as wick, burn until only ash and carbon residue remain, then place in a 775±25°C high-temperature furnace for 1.5~2 hours. The ash result is obtained by weighing.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.