Which country does the Buick Excelle come from?

What is the difference between 150 and 140 torque?

Torque 150 accelerates faster than torque 140. Definition of torque: Torque refers to the average moment of force output from the crankshaft end when the engine is running, commonly known as the engine's "rotational force." It is an important parameter of engine performance. The greater the torque, the more "force" the engine outputs, the faster the crankshaft speed changes, and the better the car's climbing ability, starting speed, and acceleration. The difference between torque and horsepower: They have different meanings. Torque refers to the force that twists an object and causes it to deform, producing a moment when the object is subjected to a tangential force in the direction of rotation. Horsepower is a unit commonly used in engineering to measure power and is a physical quantity that determines a car's top speed. They have different units: torque is measured in Newton-meters, while horsepower is measured in kilowatts. Higher horsepower results in a higher top speed, while higher torque results in greater instantaneous acceleration force. For example, commercial vehicles have very high torque output values, so they have strong instantaneous acceleration force in low-speed ranges, but their weakness is relatively low horsepower output, meaning their top speed is lower.

13

1

Share

What are the reasons for the black screen on the Beijing BJ40 central control screen?

Beijing BJ40 central control screen black screen reasons include aging wiring, prolonged usage, and circuit design defects. Aging wiring: This may be due to the aging of the power signal line of the Beijing BJ40 central control screen. You can try replacing it with a new signal line. If the black screen issue is resolved, it indicates a problem with the power signal line. Prolonged usage of the central control screen: When the Beijing BJ40 screen is used for an extended period, it can cause the power supply module to malfunction, leading not only to lag but also to a black screen in severe cases. Circuit design defects: It is necessary to go to a repair shop for inspection, repair, or direct replacement. When the Beijing BJ40 central control screen shows a black screen, you can first check whether it is caused by overheating protection due to the installation of additional devices. If the check is normal, it is recommended to take the vehicle to a professional repair facility for further inspection and handling.

1

5

Share

Does the Buick GL8 come with a built-in dash cam?

The Buick GL8 does not come with a factory-installed dash cam, but it can be optionally installed. Configuration of the Buick GL8: The Buick GL8 features a fully-wrapped design for the second-row seats, with a 30% increase in armrest width, electric sliding and unlocking functions for seat adjustment, and more. It also offers electric adjustment for seatback, lumbar support, leg rest, along with heating, ventilation, and massage functions. Additionally, it is equipped with a six-way adjustable aviation headrest, a mobile phone slot, pop-up dual cup holders, and USB charging ports. Powertrain of the Buick GL8: The Buick GL8 is powered by a 2.0T variable cylinder turbocharged engine paired with a 9-speed automatic transmission, delivering a maximum power of 174 kW, a maximum horsepower of 237 HP, and a maximum torque of 350 Nm. It provides agile gear shifting and smooth power output.

20

1

Share

How to Steer the Wheel When Making a U-turn in Driving Test Part 3?

When making a U-turn in Driving Test Part 3, you should turn on the turn signal. Here are the extended instructions: 1. As you approach the U-turn location, drive close to the right side, reduce speed and shift to a lower gear, then turn on the left turn signal. 2. Once you confirm that the U-turn maneuver will not affect vehicles in other lanes, make the left turn decisively. 3. When the front of the car is about to cross the left edge of the road, quickly straighten the wheels, brake, and turn the steering wheel sharply two full turns to the right. 4. Sound the horn and observe the traffic behind you and on both sides of the road. After ensuring safety, immediately shift into reverse gear and back up. 5. When you determine there is sufficient space to complete the left-turn U-turn, stop immediately, quickly shift into 1st gear, turn the steering wheel fully to the left, and complete the U-turn.

16

0

Share

Where is the cabin air filter located in the Zotye T600?

The cabin air filter of the Zotye T600 is located beneath the glove compartment on the passenger side, near the left side where there is a rectangular removable panel. Due to the multiple slots, a screwdriver can be inserted into the gap to slowly pry it open when removing. When taking out the old cabin air filter, observe the shape of the filter housing edge to ensure the new filter is installed in the correct orientation. Below is additional information about the cabin air filter: 1. The cabin air filter should be replaced every 10,000 to 20,000 kilometers. When the air conditioning is turned on, outside air enters the vehicle, and the cabin air filter absorbs a large amount of dust and impurities. If the filter is not replaced for a long time, its filtration performance will decline, significantly affecting the driving experience and interior hygiene. 2. Due to the limitations of the manufacturing materials, the cabin air filter cannot be cleaned with water, as a large amount of moisture can render the filter unusable. To clean it, use an air gun to blow out the dust from the opposite side. When cleaning, wear gloves, a mask, and eye protection to prevent dust and debris from entering your body.

2

1

Share

Where is the washer switch located on the old Buick GL8?

The washer switch on the old Buick GL8 is located on the control lever on the right side of the steering wheel, which is a long rod with a round head, also known as the wiper switch. How to use the washer switch: Pull the wiper lever toward the driver's position to clean the front windshield; turn the rear wiper of the old Buick GL8 to the corresponding position, activate the wiper, and push the wiper lever toward the front of the car to spray water and clean the rear windshield. Adjust the settings according to the actual weather conditions; also use the knob in the center of the lever to adjust the sensitivity of the rain-sensing wipers. Precautions when using the washer switch: It is recommended to regularly inspect and clean the wiper blades. Use a towel dampened with alcohol to wipe along the edge of the wiper blades to remove accumulated dirt, debris, and dead leaves, ensuring they remain clean at all times; check the rubber strip for cracks, wear, and unevenness. If the wear is not particularly severe, the owner can use sandpaper to smooth out any uneven surfaces.

3

Share

Which country does the Buick Excelle come from?

What is the difference between 150 and 140 torque?

What are the reasons for the black screen on the Beijing BJ40 central control screen?

Does the Buick GL8 come with a built-in dash cam?

How to Steer the Wheel When Making a U-turn in Driving Test Part 3?

Where is the cabin air filter located in the Zotye T600?

Where is the washer switch located on the old Buick GL8?

What does the lane with jagged edges on both sides mean?

Can all 4S shops perform the first maintenance for Buick cars?

How many points are deducted for making an immediate U-turn after driving in the wrong direction on the highway?

What is the purpose of the black line on the left rearview mirror of an Audi?