Which company owns NIO?

Is it necessary to replace the steering knuckle ball joint?

Whether to replace the steering knuckle ball joint depends on the situation. A loose tie rod end can cause the steering to pull to one side, uneven tire wear, steering wheel vibration, and in severe cases, the ball joint may detach, leading to sudden wheel misalignment. It is recommended to replace it promptly to avoid safety hazards. External symptoms of a damaged steering knuckle ball joint include: hearing abnormal noises when turning; feeling excessive play in the steering, resulting in unstable steering while driving; minor issues may cause unstable steering, while severe cases can lead to sudden wheel misalignment, especially at high speeds. During use, it is essential to regularly inspect the vehicle's steering ball joints and address any issues promptly to prevent a series of faults caused by steering ball joint failure. Neglecting such faults is an incorrect driving mindset, so vehicle issues should be addressed immediately. Note: After replacing the ball joint, a wheel alignment must be performed. Steering wheel misalignment is unrelated to ball joint alignment. If the steering wheel looks off, first have a professional correct it by straightening the wheels, removing the steering wheel (just a few screws), and reinstalling it in the correct position. Drive the car on a straight road, center the steering wheel, and ensure the vehicle travels straight. If the car drifts, it indicates the ball joint is not aligned correctly and requires re-alignment.

5

3

Share

Is the Accord produced by GAC Honda or Dongfeng Honda?

Accord is a model produced by GAC Honda. Since the sixth-generation Accord entered China in 1999, it has now reached its tenth generation. Below is an introduction to the GAC Honda Accord: Safety Performance: The Accord consistently applies high-level collision safety research results to its body design. The high-strength body enhances driving reliability, while the use of a sliding subframe, enlarged buffer structures, and high-strength steel plates maximizes the dispersion and absorption of impact energy, preventing deformation of the passenger compartment and injuries to occupants. Power Configuration: The new Accord is equipped with an i-VTEC intelligent variable valve timing and lift electronic control engine. The ECU computer controls the opening and closing of the intake valves to maintain the engine's optimal performance. Most importantly, it continuously provides over 80% of torque within the 2500 to 5500 rpm range.

4

Share

What is the fuel consumption of a manual Mazda 6?

Manual Mazda 6 fuel consumption is 8.0L/100km. How to calculate fuel consumption: The first method is through the vehicle's dashboard records. After resetting the mileage data, the onboard computer automatically calculates the vehicle's fuel consumption based on the recorded mileage and fuel consumption data. The second method is by recording the distance traveled after a single refueling and then calculating the vehicle's fuel consumption. The fuel consumption obtained by both methods is the average fuel consumption of the vehicle. Methods to reduce fuel consumption: When starting the vehicle, it is advisable to start in a low gear, gently press the accelerator, and gradually increase speed. Avoid suddenly pressing the accelerator hard, as this can multiply fuel consumption. Starting by gently pressing the accelerator can shorten the engine warm-up time and effectively improve fuel utilization, thereby achieving fuel-saving effects.

20

1

Share

Is the Motorcycle Exempt from Inspection for 6 Years or 4 Years?

Motorcycles are exempt from inspection for the first 6 years. However, exemption from inspection does not mean exemption from annual review. It only means that the vehicle does not need to undergo on-site inspection, i.e., the vehicle does not need to go to a testing institution or the vehicle management office for safety and technical inspection. Nevertheless, the owner must still bring relevant documents to the vehicle management office every two years to collect the inspection compliance label. After three exemptions, the vehicle must undergo on-site inspection every year. The 6-year exemption policy only applies to new vehicles. From the date of registration, the inspection cycle remains unchanged. According to the original cycle regulations, inspections are required every two years for the first 4 years, and then once a year. For new vehicles, the inspection compliance label must be applied for in the 2nd, 4th, and 5th years after registration, without the need for on-site inspection at a testing institution. Motorcycles registered for more than 6 years (including 6 years) must undergo on-site inspection at a testing institution every year. For passenger vehicles used for commercial purposes, inspections are required once a year within the first 5 years and every 6 months thereafter. For trucks and large or medium-sized non-commercial passenger vehicles, inspections are required once a year within the first 10 years and every 6 months thereafter. For small and micro non-commercial passenger vehicles, inspections are required every two years within the first 6 years, once a year thereafter, and every 6 months after 15 years. For motorcycles, inspections are required every two years within the first 4 years and once a year thereafter.

4

1

Share

What are the advantages of full synthetic engine oil?

The advantages of full synthetic engine oil are as follows: 1. Excellent low-temperature fluidity: Full synthetic oil has low viscosity and high viscosity index, which can save energy consumption during cold starts, accelerate oil film formation, and reduce dry wear phenomena in engine components during cold starts; 2. Excellent high-temperature oxidation resistance: Synthetic oil has better thermal oxidation stability than mineral oil, ensuring performance stability during long-term use; 3. Low evaporation loss: The evaporation loss of synthetic oil is much lower than that of mineral oil, which can improve fuel economy, reduce exhaust emissions, and extend the service life of catalytic converters.

7

5

Share

How to deal with P1545 trouble code?

p1545 trouble code is caused by throttle carbon deposit being too dirty, throttle not fully closing, throttle position actuator or its circuit or connector failure, etc. The solutions include cleaning the throttle or directly replacing it with a new one. It is recommended to go to a 4S shop for inspection and repair. More relevant information is as follows: 1. The throttle, commonly known as the accelerator, is a controllable valve used to regulate the engine's air intake. 2. The Throttle Position (TP) sensor's function is to send the throttle opening degree to the Electronic Control Unit (ECU) in the form of an electrical signal, serving as one of the basic parameters for controlling engine fuel injection.

10

3

Share

Which company owns NIO?

Is it necessary to replace the steering knuckle ball joint?

Is the Accord produced by GAC Honda or Dongfeng Honda?

What is the fuel consumption of a manual Mazda 6?

Is the Motorcycle Exempt from Inspection for 6 Years or 4 Years?

What are the advantages of full synthetic engine oil?

How to deal with P1545 trouble code?

What is the weight of vehicle-mounted fire extinguishers as stipulated by national regulations?

What is the weight of the Boyue in tons?

How to Turn Off the Air Conditioning in a Chevrolet Cruze?

What is the recommended speed for a new car during the high-speed break-in period?