Which company manufactures the Leapmotor C11?

1 Answers
Simoes
07/28/25 3:40pm
Leapmotor C11 is produced by Leapmotor, the full name of the company is Zhejiang Leapmotor Technology Co., Ltd. The company was established on December 24, 2015, and is an innovative intelligent electric vehicle brand. The main investor of the company is Zhejiang Dahua Technology Co., Ltd., and its headquarters is located in the Binjiang High-Tech Development Zone, Hangzhou, Zhejiang. Here is some relevant information about Leapmotor: 1. Brand Introduction: Leapmotor is an intelligent electric vehicle brand invested in by the listed company Zhejiang Dahua Technology Co., Ltd., with its headquarters located in the Binjiang High-Tech Development Zone, Hangzhou, Zhejiang. The company's main R&D focuses on intelligent connectivity, motor and electronic control, battery systems, and vehicle design. 2. Brand Philosophy: Leapmotor is an innovative intelligent electric vehicle enterprise with complete independent R&D capabilities for intelligent electric vehicles. It was jointly invested in by Zhejiang Dahua Technology Co., Ltd. and its main founders. The company consistently adheres to independent R&D of core technologies and is committed to building a high-quality, international, and globally mainstream intelligent electric vehicle brand with core technological capabilities.
Was this review help?
20
0
Share
More Forum Discussions

Can Spark Plugs Cause Increased Fuel Consumption?

Damaged spark plugs can lead to increased fuel consumption and should be replaced promptly. Methods to determine if a spark plug is damaged: Remove the spark plug and observe its appearance. The condition of the spark plug can be judged based on its color. A normal spark plug's insulator skirt and electrodes should appear gray-white, gray-yellow, or light brown. A properly functioning spark plug has a reddish-brown insulator skirt, with an electrode gap between 0.8-0.9mm and no signs of electrode burn. If the spark plug is covered in oil or deposits but is not damaged, it can continue to be used after cleaning off the oil and deposits. If the spark plug is severely damaged, with signs such as blistering, black streaks, cracks, or melted electrodes, the cause of the damage should be identified. After troubleshooting, replace the spark plug with a new one. Additionally, if the spark plug appears black as if smoked, it indicates the wrong heat range was selected or the air-fuel mixture is too rich, with oil seeping up. Steps to replace spark plugs: Open the engine hood and remove the plastic engine cover. Disconnect the high-voltage wires, marking each cylinder's position to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for external debris like leaves or dust and ensure the area is clean. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the high-voltage wires in the correct firing order and reattach the cover.
15
3
Share

Can a child be held in the front passenger seat?

It is not allowed to hold a child in the front passenger seat. According to the Road Traffic Safety Law, children under the age of 12 are not permitted to sit in the front seats of a motor vehicle. For preschool-aged children sitting in the rear seats, special child seats must be used as required. If a parent holds a child in the front passenger seat of a private car, they will be fined without any penalty points deducted. Data from the Australian Insurance Group, the parent company of CAA, shows that when children sit in the rear seats, fatal injuries are reduced by one-third, regardless of whether the car has airbags. Therefore, regardless of whether the car has airbags, the best way to protect children is to place those under 12 years old in the rear seats of the car.
10
3
Share

What Do the Numbers on a Tire Mean?

Tire numbers represent the tire's width, aspect ratio, type, and applicable rim size. Taking the 225/60/R17 model as an example: 225 indicates the tire's section width is 225mm; 60 is the aspect ratio, meaning the tire's sidewall height is 60% of the section width; R stands for radial tire; 17 means the tire fits a 17-inch rim. Radial tires have steel belts in the tread area, allowing them to withstand higher internal pressure stress, with characteristics such as less tread deformation, better road grip, and stability, making them more suitable for high-speed driving. Most modern passenger cars use radial tires.
12
1
Share

What Causes Car Engine Idle Shaking That Disappears When Accelerating?

Idle resonance occurs when the engine's idle excitation frequency couples with the natural frequency of the steering system or vehicle body, causing vibration. When the throttle is fully engaged, the change in engine excitation frequency increases, avoiding the natural frequency points of certain parts of the transmission system or vehicle body, thus eliminating the vibration. If there's slight body sway or deviation while driving, it's usually tire-related. The primary cause could be improper wheel balance, requiring the owner to perform a four-wheel alignment and dynamic balancing promptly. If the vehicle doesn't deviate, perform tire dynamic balancing. Another more serious scenario might involve deformed steel rims, necessitating inspection at a professional repair shop. This condition typically occurs in vehicles with extended service life. Generally, when replacing new tires and rims, proper wheel balancing must be performed; otherwise, uneven weight distribution can easily cause steering wheel vibration. Body sway affects driving comfort and handling judgment. The third situation is caused by unbalanced or deformed drive shafts, usually occurring after multiple vehicle collisions with the chassis. Car vibration is also related to aging engine mounts (also called cushion pads). Engine mounts essentially serve as the engine's shock absorber system, responsible for absorbing minor vibrations during engine operation. If engine mounts are faulty, these vibrations transmit to the steering wheel and cabin, causing idle vibration.
17
3
Share

Can a slightly bulged tire still be used?

A slightly bulged tire can still be used, but only after the damaged area has been repaired through hot vulcanization. This method involves using high-temperature vulcanization to fuse raw rubber into the tire wound, which then cools and solidifies to seal and repair the damage. This repair process has high technical requirements, as the timing during high-temperature vulcanization must be precise; otherwise, it may cause varying degrees of impact. A tire bulge occurs when the cords inside the tire's inner ply break, allowing air to push outward from the broken cords. Without the support of these cords, the elastic rubber forms a bulge under the pressure of the air. In other words, a bulged tire indicates that the internal cords have already broken. If not repaired and continued to be used, it may lead to a tire blowout.
20
2
Share

Can I Take the Subject Two Test Immediately After Passing Subject One?

No, you cannot. According to Article 36 of the 'Regulations on the Application and Use of Motor Vehicle Driving Licenses,' the vehicle management office must arrange tests based on the scheduled test center and time. After passing the Subject One test, applicants can schedule the Subject Two or Subject Three road driving skills test. Students must first pass the Subject One test before they can schedule the Subject Two or Subject Three road driving skills test. For a Class C license, you can schedule the Subject Two test online 10 days after passing Subject One. For Class A or B licenses, you must wait 20 days after passing Subject One before scheduling the Subject Two test. Each Subject Two test appointment allows for two attempts. If the first attempt is unsuccessful, a free retake is available. If you do not take the retake or fail the retake, the test session ends, and you can reschedule the Subject Two test after 10 days. Within the validity period of the learning license, the number of Subject Two test appointments must not exceed five. If the fifth attempt is still unsuccessful, the results of other previously passed subjects will be invalidated. To continue learning for the driving license, you must restart from Subject One. Subject Two, also known as the small road test, is part of the motor vehicle driving license assessment. It refers to the field driving skills test. For small vehicles (C1), the test includes five mandatory items: reverse parking, parallel parking, hill start, right-angle turns, and curve driving (commonly known as S-turns). Some regions may include a sixth item, such as highway card collection. For C2 vehicles, the test includes four mandatory items: reverse parking, parallel parking, right-angle turns, and curve driving (S-turns). For large vehicles (A1, A2, A3, B1, B2), the test includes multiple items: pole test, hill start, parallel parking, single-plank bridge crossing, curve driving, right-angle turns, narrow gate crossing, continuous obstacle crossing, bumpy road driving, narrow road U-turns, and simulations for highways, continuous sharp mountain roads, tunnels, rain/fog conditions, slippery roads, and emergency handling. Subject Two Test Tips: After getting into the car, adjust the seat and mirrors to a comfortable position and ensure the seatbelt is fastened. For parallel parking, find the correct angle and turn the steering wheel quickly, reacting promptly to match the car's speed. For hill starts, remember to engage the handbrake, turn on the left indicator, and release the handbrake. Keep the clutch steady while gradually pressing the accelerator to avoid stalling or rolling back. For right-angle turns, identify the turning point quickly and react accordingly, matching the car's speed to avoid deviation. For curve driving (S-turns), reduce speed and proceed slowly. Those with good driving instincts may pass smoothly in one go. For reverse parking, control the speed, identify reference points, and make minor adjustments if deviations are observed in the mirrors. The driving test consists of three subjects: Subject One, Subject Two, and Subject Three. Subject One refers to the traffic safety laws, regulations, and related knowledge test. Subject Two refers to the field driving skills test. Subject Three is divided into two parts: road driving skills and safe driving knowledge. The safe driving knowledge test is conducted after Subject Three, often referred to as Subject Four. However, the official term (under the Ministry of Public Security Order No. 123) does not include 'Subject Four.'
5
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.