Which city does the Yue E license plate belong to?

2 Answers
AveryDella
07/28/25 11:58pm
Yue E license plate belongs to Foshan City, Guangdong Province. The license plate codes for various regions in Guangdong are as follows: Yue A is Guangzhou City, Yue B is Shenzhen City, Yue C is Zhuhai City, Yue D is Shantou City, Yue E is Foshan City, Yue F is Shaoguan City, Yue G is Zhanjiang City, Yue H is Zhaoqing City, Yue J is Jiangmen City, Yue K is Maoming City, Yue L is Huizhou City, Yue M is Meizhou City, Yue N is Shanwei City, Yue P is Heyuan City, Yue Q is Yangjiang City, Yue R is Qingyuan City, Yue S is Dongguan City, Yue T is Zhongshan City, Yue U is Chaozhou City, Yue V is Jieyang City, Yue W is Yunfu City, Yue X is Shunde District, Yue Y is Nanhai District, Yue Z is for vehicles entering the mainland from Hong Kong and Macau.
Was this review help?
10
0
Share
McDelilah
08/12/25 4:15am
The license plate starting with 粤E is the exclusive code for Foshan City in Guangdong Province. Every time I see a car with 粤E on the highway, it feels particularly familiar. Speaking of Foshan, it’s not just the license plate that’s special—as the third-largest economic city in Guangdong, 粤E has grown alongside local automakers like GAC Trumpchi and Honda. I once heard from a friend that Foshan car owners often enjoyed exclusive annual ETC discounts, though I’m not sure if the policy has changed now. Last year, while dining in Shunde, I noticed that 70% of the cars in the parking lot had 粤E plates, and it suddenly struck me how this little metal plate ties together the vibrant essence of a city.
Was this review help?
18
2
Share
Expand All
More Forum Discussions

How to Add a Driving License Category?

To apply for an additional driving license category, you must meet the corresponding conditions and submit an application to the vehicle management office. After passing all the required tests, you will obtain the additional driving qualification. Below is the relevant introduction about driving licenses: 1. Laws and Regulations: According to Article 40 of the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," first-time applicants for a motor vehicle driving license or those applying to add a permitted driving category must schedule the second subject test. 2. Application Conditions: To apply for an additional category, if your original permitted categories are C1, C2, C3, or C4, you must have at least 3 years of driving experience and no full penalty points in the last 2 scoring cycles to upgrade to a B1 license. For those with B1 or B2 categories, you need at least 3 years of driving experience and no full penalty points in the last 2 scoring cycles to upgrade to an A2 license. To upgrade to an A2 license from an A1 license, you must have at least 1 year of driving experience and no full penalty points in the last scoring cycle.
16
1
Share

Is it necessary to change the transmission fluid for manual transmissions?

Manual transmissions require transmission fluid changes. The hazards of not changing the transmission fluid are as follows: 1. Starting: The car may experience weak acceleration when starting cold. 2. Heat dissipation: The transmission fluid may thicken, potentially blocking the transmission cooler, leading to excessively high transmission fluid temperatures and increased wear. 3. Aging: The transmission fluid may degrade, not only increasing fuel consumption but also shortening the transmission's lifespan. 4. Blockage: Particles may form in the transmission fluid, clogging the fluid passages and damaging the valve body, directly affecting system pressure and power transmission, resulting in delayed responses and harsh shifting.
6
2
Share

Do I Need to Add Cleaner When Using Ethanol Gasoline?

Switching to ethanol gasoline does not require adding a cleaning agent. Here is some relevant information about ethanol gasoline: 1. Performance of Ethanol Gasoline: As a new generation of clean and environmentally friendly fuel, ethanol gasoline itself is an excellent organic solvent with strong dissolving effects. After adding ethanol gasoline, impurities, dirt, and sediments at the bottom of the fuel tank and in the fuel lines will automatically soften and dissolve into the gasoline. 2. Cleaning the Fuel Lines: If no issues occur after switching to ethanol gasoline, there is no need to clean the fuel lines even after driving 30,000 kilometers. However, for cars that have been idle for over a year without use, it is recommended to clean the fuel lines, as gasoline that hasn't flowed for a year will have relatively more deposits.
7
2
Share

How to Check Motorcycle Fuel Level?

Check the motorcycle's fuel gauge. 'F' indicates a full tank, while 'E' in the red zone indicates low fuel. When the fuel gauge needle points to the red zone near 'E', there is still approximately one-third to one-fourth of the total fuel capacity remaining in the tank, at which point the rider should refuel. For cross-type motorcycles, you can also rely on the fuel tank switch. After filling up, set the switch to the main tank. When the main tank runs out of fuel, switch to the reserve tank, and after refueling, switch back to the main tank. The fuel gauge is used to indicate the amount of fuel remaining in the vehicle's fuel tank. It can be either a pointer or a digital display. The fuel gauge consists of a stabilized fuel level indicator and a fuel level sensor. Refueling precautions: Do not wait until the warning light comes on to refuel. Since the fuel pump is located inside the tank and relies on fuel for cooling and lubrication, insufficient fuel can impair the pump's normal operation and reduce its lifespan. It is also not advisable to fill the tank completely. Gasoline expands when heated and evaporates into vapor, especially in high summer temperatures, requiring space to accommodate this. If the tank is filled to the brim with no space left, gasoline vapor or even liquid fuel may enter the carbon canister for storage. Once the canister is full, the excess will escape into the air, leading to waste and environmental pollution.
13
0
Share

How to Turn Off the Daytime Running Lights on a Geely Emgrand?

Turn to the radio playback position, twist the combination switch on the left side towards the driver and simultaneously downwards, and do not let go. Wait for about 3 seconds until you hear a beep sound, indicating that the daytime running lights have been turned off. Finally, if you need to turn the daytime running lights back on, simply reverse the previous steps.
19
5
Share

What to do if the steering wheel has different turning circles left and right?

If the steering wheel has different turning circles left and right, it can be adjusted through rough adjustment, fine adjustment, and steering wheel position adjustment. Here are the relevant details: 1. Rough Adjustment: Drive the vehicle onto a four-wheel alignment machine. Under the premise that the camber angles of both wheels are basically symmetrical, adjust the adjustment nuts of the tie rods to make the lengths on both ends as equal as possible and ensure that the toe angles on both sides approach the same value symmetrically. For example, 0 degrees. If there are persistent contradictions in the above steps, it may indicate that the frame or suspension is damaged or deformed, requiring frame adjustment or part replacement. 2. Fine Adjustment: Use a 5053 diagnostic tool to check whether the angles when the steering reaches its limits on both sides are roughly symmetrical, within a range of 5 to 10 degrees. Then, locate the electronic zero point and immediately fix the steering wheel. Perform a standard or required four-wheel alignment. After completion, drive the vehicle off the alignment machine, reset the G85, and conduct a short test drive to check for any deviation. If deviation occurs, perform another alignment and make necessary compromises in the alignment values. 3. Adjusting the Steering Wheel Position: Turn off the engine, remove the airbag module, connect the 5053 tool, and set the ignition to the self-test position (alarms may sound). Position the steering wheel at the electronic zero point, then use a puller to remove the steering wheel and adjust its position. The ideal scenario is that when the 5053 tool indicates the steering angle is at zero, the steering wheel spokes are as vertical as possible. After completion, reinstall the airbag and other components, then clear any fault codes.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.