Which car has a cross as its logo?

1 Answers
LouisFitz
07/29/25 4:07pm
Lincoln's logo features a cross. It belongs to Ford Motor Company in the United States. Taking the Lincoln Nautilus as an example, its body dimensions are: length 4849mm, width 1936mm, height 1691mm, with a wheelbase of 2849mm, a fuel tank capacity of 70 liters, and a body weight of 1933kg. The Lincoln Nautilus has a MacPherson strut front suspension and a multi-link independent rear suspension. It is equipped with a 2.0T turbocharged engine, delivering a maximum horsepower of 224PS, a maximum power of 165kW, and a maximum torque of 368Nm, paired with an 8-speed automatic transmission.
Was this review help?
1
5
Share
More Forum Discussions

How to adjust the date on BYD Song display?

First, press the time adjustment button on the left side of the BYD Song's instrument panel, and the hour digits on the display will start blinking. Then, press the time adjustment button on the right side of the BYD Song's instrument panel to increase the hour value with each press. Once the hour value on the BYD Song's instrument panel stops blinking, press the left time adjustment button again. Finally, use the right time adjustment button to set the correct value, and the time on the BYD Song's instrument panel will be accurately adjusted.
1
2
Share

What to Do When Your Car Stalls in Heavy Rain and Flooded Roads?

If your car is in floodwater, please stay calm and do not attempt to restart the engine. Push your car out of the floodwater to prevent prolonged submersion. Call your insurance company to arrange for a tow truck; if you don't know the number, you can look it up online. Have the car towed to your preferred repair shop or to one designated by your insurance company. Before repairing the car, make sure to file an insurance claim to minimize potential losses.
19
0
Share

How to loosen the wedge-type self-adjusting brake of FAW J6P?

Remove the rubber plugs from the adjustment inspection hole and gap inspection hole on the protective plate; check the gap between the brake shoe and brake drum, adjust the nut state - tighten clockwise and loosen counterclockwise. Use a flashlight to observe the position of the adjustment side bolt, and use a flat-head screwdriver to turn the external teeth of the adjustment bolt to reduce the gap between the brake shoe and brake drum. The gap between the caliper, brake disc, and brake drum is mostly self-adjusting and does not require manual adjustment.
20
2
Share

What are the reasons for Neta Auto charging display malfunction?

Brief introduction to Neta Auto charging malfunction: Battery fully charged: If the battery of a new energy vehicle is already fully charged, it will naturally not accept further charging. This is a normal phenomenon. Large temperature difference: If the charging environment temperature is too low or too high, the new energy vehicle will also fail to charge. Generally, the charging temperature for new energy vehicles ranges from -20°C to approximately 65°C. Battery malfunction: If the battery of a new energy vehicle malfunctions, it will also fail to charge. Repair methods:
1
0
Share

What are the steps for refueling?

Determine if refueling is needed by first checking the remaining mileage. Generally, it's advisable to refuel when the remaining distance is below 200 kilometers, but this may vary depending on your driving conditions. Slowly drive the vehicle into the gas station, avoiding stopping at the station's entrance. Once at the refueling spot, turn off the engine and open the fuel tank valve. Inform the attendant about the type of gasoline needed, specifying the amount to refuel (either by cost or a full tank). After refueling, ensure the fuel cap is securely closed before restarting the engine. When leaving the gas station, be cautious with your turning angle to prevent the rear left wheel from scraping against the fuel pump.
7
5
Share

What to Do When Water Enters the Car Engine Block?

Should move the vehicle out of the deep water area to ensure that the engine intake will not inhale water again, and park in a safe place. Manually cut off the fuel supply system and ignition system, then use the motor to run the engine, allowing the water that has entered the engine to be discharged smoothly. After the inspection is completed, use compressed air to clean the electrical connection parts inside the engine compartment to prevent corrosion caused by water accumulation in the electrical connection areas. After cleaning, conduct a road test of the vehicle to ensure that there are no abnormal noises from the engine during driving. If there are obvious driving noises, check the engine bearings and rotating parts.
7
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.