Which button unlocks the trunk of the Volkswagen Lavida?

What causes the noise when turning the steering wheel while stationary?

The reasons for noise when turning the steering wheel while stationary are: 1. Lack of lubrication in the steering column, causing high friction; 2. Check if the power steering fluid is low; 3. Inspect the universal joint for any issues; 4. Aging and hardening of the rubber bushings in the chassis suspension stabilizer bar links; 5. Damage to the thrust bearing. Relevant information about the steering wheel is as follows: 1. Introduction: Generally connected to the steering shaft via splines, its function is to convert the force applied by the driver to the edge of the steering wheel into torque, which is then transmitted to the steering shaft. 2. Usage considerations: When using a larger diameter steering wheel, the force required from the driver's hands can be reduced. The steering intermediate shaft, as a connecting component between the steering gear and the steering shaft, facilitates the standardization of the steering gear, compensates for errors during manufacturing and installation, and ensures more rational installation of the steering gear and steering wheel in the vehicle.

12

1

Share

What is the percentage of speeding when driving at 85 in an 80 speed limit zone?

Driving at 85km/h in an 80km/h speed limit zone is considered speeding, with a speeding ratio of 6.25% (calculation method: (85-80) ÷80x100%=6.25%). Relevant information about speed limits is as follows: 1. Introduction: Speed limits typically refer to the regulation of vehicle speeds within a certain numerical range over a specific distance. They are imposed to maintain normal, stable, and safe production orders and operational processes by setting necessary speed restrictions on various mechanical and electrical equipment and manual operations, thereby preventing accidents or malfunctions caused by overloading or other reasons. 2. Purpose: The primary goal is to preemptively remind drivers to reasonably control their speed in subsequent sections of the road ahead and to prevent the dangers of speeding. Speed limits are an indispensable and most crucial aspect of road transport safety.

3

Share

What is the size of an R18 tire?

R18 tires are 18 inches in size. Here are some tire maintenance tips: 1. Regularly check tire pressure: Tire pressure is a crucial factor affecting tire lifespan. It should neither be too high nor too low; always inflate according to the vehicle's recommended tire pressure. In summer, try to keep the tire pressure slightly lower. In winter, ensure the tire pressure is slightly higher than in summer due to thermal expansion and contraction. 2. Inspect for wear: Some vehicles may experience uneven tire wear. Frequently check the inner side of the tires for abnormal wear, focusing on whether the tread depth is consistent on both sides. 3. Remove foreign objects promptly: Debris in the tire treads can pose potential hazards and may fly out while driving. 4. Perform wheel alignment regularly: If the vehicle pulls to one side or exhibits unusual steering behavior, get the tires aligned promptly to prevent further issues. Wheel alignment ensures even force distribution across all four tires, avoiding excessive wear.

1

5

Share

How long should you keep the engine running after a jump start?

After jump-starting the vehicle, you should keep the engine running for at least 30 minutes to ensure sufficient battery charge. A dead battery could be due to complete discharge or battery failure. If the battery is discharged, you can attempt to start the vehicle using another car and jumper cables. If the battery is damaged, it should be repaired or replaced promptly. Jump-starting method: 1. Connect the positive and negative terminals of the dead battery to the corresponding terminals of the donor vehicle using jumper cables, connecting the positive terminal first followed by the negative terminal. (Always connect positive to positive and negative to negative, avoiding reversed connections or contact between opposite terminals) 2. Keep the donor vehicle running while the recipient vehicle completes the above steps and starts normally. (After starting, the recipient vehicle should turn off all electrical accessories when possible) 3. The recipient vehicle should ideally run for over 30 minutes when conditions permit to fully recharge the battery.

3

1

Share

What does MT mean?

In automobiles, MT stands for Manual Transmission, also known as manual gearbox. It requires manually shifting the gear lever to change the gear engagement positions inside the transmission, altering the gear ratio to achieve the purpose of changing speeds. A manual transmission is a gear-shifting device used to modify the speed and torque transmitted from the engine to the drive wheels. It enables the vehicle to obtain varying traction and speed under different operating conditions such as starting from a standstill, climbing hills, turning corners, and accelerating, while also allowing the engine to operate within a more favorable range. Functions of manual transmission: Changing the gear ratio to expand the range of torque and speed variations at the drive wheels, adapting to frequently changing driving conditions. Under the premise that the engine's rotation direction remains unchanged, the reverse gear is used to enable the vehicle to move backward. With the engine still running, the neutral gear interrupts power transmission, which is beneficial for engine startup, warm-up, idling, and facilitates gear shifting, coasting, or temporary parking. The transmission can also divert engine power to drive other mechanisms, such as the winch on certain vehicles or the oil pump of dump trucks.

19

2

Share

How to Break in a New Car?

New car break-in methods are as follows: 1. Initial break-in: The first 500 kilometers is the initial break-in period, during which the speed should not be too fast, generally below 70-80 km/h, and the engine speed should preferably not exceed 2,200 rpm. 2. Mid-term break-in: 500-1,000 kilometers is the mid-term break-in period, where the maximum speed can be appropriately increased, generally up to 90-100 km/h, with engine speed preferably below 2,500 rpm. Appropriately increasing speed will not affect the engine but can promote break-in, and you can also check for any abnormalities during acceleration. 3. Final break-in: 1,000-1,500 kilometers is the final break-in period, during which the speed can be increased to below 120 km/h. Because break-in is a gradual process, it must be done step by step. The engine speed should not exceed 3,000 rpm.

14

1

Share

Which button unlocks the trunk of the Volkswagen Lavida?

What causes the noise when turning the steering wheel while stationary?

What is the percentage of speeding when driving at 85 in an 80 speed limit zone?

What is the size of an R18 tire?

How long should you keep the engine running after a jump start?

What does MT mean?

How to Break in a New Car?

What is the reason for blue smoke coming from the exhaust pipe?

Should the Parking Brake Be Pulled Up or Down?

Can a car that has been using 92-octane gasoline switch to 95-octane gasoline?

Is It Easy to Learn to Drive an Automatic Car?