Which button to press for defogging in Corolla on rainy days?

1 Answers
McOwen
07/29/25 6:55pm
To defog in a Corolla on rainy days, you need to turn on the rear windshield defogger switch and the rearview mirror heating button. Reasons for foggy car windows: The temperature of the car glass is lower than the dew point; there is a significant temperature difference between the inside and outside of the car. Methods for defogging a car on rainy days: Turn on the front window defogging mode, increase the fan speed, turn on the temperature switch, and lower the temperature. Activate the one-touch defogging function, open the windows to increase air convection, reduce the temperature difference between the inside and outside of the car, and weaken the conditions for fog formation. Spray defogging agent evenly on the glass surface and wipe it clean with a dry towel. Make a homemade defogging agent with dish soap and spray and wipe it before traveling.
Was this review help?
7
5
Share
More Forum Discussions

Where is the cabin air filter located in the 2011 Teana?

The cabin air filter in the 2011 Teana is located beneath the glove compartment on the passenger side, near the left foot area of the front passenger seat. The filter housing is positioned behind the air intake and can be difficult to locate, typically requiring some probing to find. Notes for replacing the Teana cabin air filter: 1. No need to remove the glove compartment for filter replacement. 2. The OEM filter features upper and lower pull tabs for easy removal. If the new filter lacks these tabs, it may complicate future replacements. You can wrap a loop of tape around the new filter with the adhesive side facing outward to facilitate future removal. 3. When closing the filter housing cover, ensure the top edge of the cover properly engages with the slot above the filter housing. Improper alignment may cause the cover to become loose due to poor sealing.
10
4
Share

Can a Newly Purchased Car Go on Long Trips?

It is not advisable for a new car to go on long trips. During the break-in period, running a new car on long trips increases the continuous working time of the engine, which can easily cause wear and tear on the components. It is important to note that new cars should avoid emergency braking, as it not only impacts the braking system during the break-in period but also increases the load on the chassis and engine. It is best to avoid emergency braking within the first 300 kilometers of driving. Precautions during the break-in period of a new car include: 1. Warm up the car before starting: After shifting into second gear, wait for 5 to 10 seconds before starting the engine. 2. Avoid high-speed driving: During the break-in period, the speed of a new car should be limited. For domestic cars, the speed should be between 40 to 70 kilometers per hour, while for imported cars, it should be around 100 kilometers per hour. 3. Avoid overloading: Loading too much in a new car during the break-in period can cause damage to the components. 4. Do not remove the speed limiter prematurely: The speed limiter is a throttle device installed between the carburetor and the intake pipe. Owners should not remove the speed limiter too early; it should be removed after driving 1000 kilometers. 5. Avoid changing the oil too early: The initial oil used in a car is specifically designed for the break-in period. This type of oil has low viscosity, good heat dissipation, and excellent oxidation resistance. 6. Do not perform emergency braking: Emergency braking not only impacts the braking system during the break-in period but also increases the load on the chassis and engine.
9
3
Share

How to open the hood of an Audi Q2L?

Locate the hood release lever in the lower left corner of the driver's compartment. When activated, you will hear a sound indicating the hood has been released. Gently lift the hood with one hand while using your other hand to release the safety latch. Some models require pulling the latch to the left, but in this case, pull it to the right, then lift the hood upward. Find the hood support rod inside the engine compartment and pull it out. Position the rod into its designated holder, typically marked by a corresponding socket on the underside of the hood.
4
4
Share

How to reset the maintenance light on a Haval F7?

Here is the method to reset the maintenance light on a Haval F7: 1. With the engine turned off, press and hold the short-distance trip counter reset button located below the tachometer. 2. While holding the button, turn on the ignition (do not start the engine), then release the short-distance trip counter reset button. When the SERVICE indicator appears on the display, pull out the minute button on the clock and turn it clockwise. 3. After the odometer reading appears on the display, turn off the ignition to complete the maintenance light reset. Below is some relevant information about the Haval F7: 1. Suspension: It features a four-wheel independent suspension system with MacPherson struts in the front and double wishbones in the rear. 2. Body dimensions: The vehicle measures 4715mm in length, 1925mm in width, 1718mm in height, with a wheelbase of 2850mm.
13
3
Share

Do cars with ABS systems need to pump the brakes?

Cars with ABS systems do not need to pump the brakes. The function of ABS is to prevent wheel lock-up and avoid loss of control. During emergency braking, pumping the brakes should not be used. The advantage of pumping the brakes is to prevent the ABS from activating, but in emergency situations, you should brake hard to allow the ABS to work. Once the ABS is activated, the anti-lock braking system remains on standby. Most cars cannot manually turn off the ABS. The best practice is to drive at a low speed to the nearest 4S shop for inspection and repair of potential safety hazards after the ABS is triggered, or to park the car on the roadside and request emergency towing services. ABS effectively maintains braking performance during emergency stops, maximizing driving safety in sudden accidents. "ABS" is the Chinese translation of Anti-lock Braking System, a vehicle safety control system with advantages such as anti-skid and anti-lock functions. ABS is an improved technology based on conventional braking systems and can be divided into mechanical and electronic types. Modern vehicles are widely equipped with anti-lock braking systems, which not only provide the braking function of conventional systems but also prevent wheel lock-up.
3
3
Share

Where is the air conditioning filter located on the Changan Yuexiang V7?

The air conditioning filter of the Changan Yuexiang V7 is located behind the glove compartment on the passenger side. Steps to replace the air conditioning filter on the Changan Yuexiang V7: 1. Open the glove compartment on the passenger side. 2. Remove the screws on the glove compartment and take it off. 3. You will then see the air conditioning filter; remove the cover plate. 4. Finally, you can remove the air conditioning filter. Functions of the air conditioning filter: 1. Provides fresh air, preventing the car windows from fogging up and ensuring clear visibility for the driver, enhancing driving safety. 2. Ensures hygiene and safety by keeping the cabin air clean and free from bacteria, creating a healthy environment. 3. Absorbs harmful substances, including moisture, soot, ozone, odors, carbon oxides, SO2, CO2, etc., from the air. 4. Filters solid particles, as the air conditioning filter fits tightly against the housing, ensuring that unfiltered air does not enter the cabin.
13
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.