Which button is the defogger in the car?

What Causes the Abnormal Noise After Clutch Replacement?

The reasons for abnormal noise after clutch replacement are as follows: Gear Noise: The sound is caused by worn and thinned gear teeth leading to excessive clearance, resulting in impact noise during operation; poor gear meshing; fatigue-induced tooth surface spalling or individual tooth breakage; excessive clearance in the spline fit between the gear and shaft; shaft bending or loose bearings at both ends of the shaft causing changes in gear meshing clearance; or improper adjustment of axial shims leading to poor gear meshing. Bearing Noise: Abnormal noise due to worn internal transmission bearings; or caused by gear oil being too thin or of poor quality; abnormal clearance between the inner and outer rings of the bearing and the shaft neck hole; bearing balls having pits or bearing inner/outer races showing signs of burning and pitting. Other Causes: Such as insufficient oil inside the transmission or gear oil being too thin and of poor quality; foreign objects falling into the transmission or loose internal fastening bolts causing abnormal noise.

12

2

Share

Is an Engine Not Being Broken Not Considered a Scrapping Standard?

Generally, when the vehicle reaches 10 years of age, even if the engine is not broken to the point of being irreparable, the vehicle management department will still enforce mandatory scrapping. Regarding engine repair: By replacing parts, the engine can be fixed, but the issue lies in the cost. Components like the cylinder block, cylinder head, crankshaft, and camshaft are relatively expensive, making the replacement costs quite high. Remanufactured engines involve repairing used engines through specific processes, allowing them to be reused with performance and power consumption differing by about 10% compared to original factory engines. Five bad habits that most easily lead to engine scrapping: Driving at high gear with low speed, adding excessive engine oil, using mismatched fuel grades, not warming up the engine or overheating it, and not replacing the timing belt in a timely manner.

18

1

Share

Is a slightly deformed small car wheel hub a big problem?

A slightly deformed small car wheel hub can have significant impacts and is highly likely to cause direct fracture of the hub if it hits an obstacle while driving. About wheel hub material: Aluminum alloy, as a metal material, can be bent back into shape like a straightened wire, but after two or three attempts, it will break—let alone a large wheel hub. If the hub is forcibly restored to its original shape, it may look new externally, but its internal structure becomes very fragile. If the repaired area is impacted again during driving, the hub could fracture directly, leading to a serious traffic accident. Repair method: First, cushion the dented area with sponge or cloth, then use a hammer to forcefully flatten the dent. The flattened area will be uneven, so use body filler (commonly known as putty) to smooth it out. Afterward, roughen the inside of the hub with sandpaper to prepare for the next step—painting.

16

4

Share

Are There Motorcycles Equipped with Air Conditioning?

There are motorcycles equipped with air conditioning. For example, the Honda Gold Wing GL1800. Here is some related information about the Honda Gold Wing: Features of the Gold Wing: The Honda Gold Wing GL1800 is a sport touring motorcycle, which emphasizes comfort and stability. Some people refer to this motorcycle as the Rolls-Royce of motorcycles, acknowledging its prestigious status in the motorcycle world. In terms of appearance, this motorcycle is very grand, and its body is made of aluminum alloy. It can reach a top speed of 105 km/h. The motorcycle weighs 363 kg and has a maximum output power of 93 kW. Configuration of the Gold Wing: The large radiators on both sides are eye-catching, and this design also ensures effective heat dissipation. Additionally, during winter, the heat can be circulated. The ignition switch of this motorcycle is a button, meaning it features keyless start.

18

2

Share

Can the Engine Be Restarted After Water Intake?

After a vehicle has been submerged in water, it is strictly prohibited to attempt a restart. The reasons are as follows: 1. Damage to the Engine Block: If the vehicle stalls during water submersion, it indicates that water has entered the engine. Since water is incompressible, the piston cannot reach its original top dead center position, resulting in a shorter piston stroke and a noticeable downward shift in the top dead center position. Attempting to restart the engine under these conditions can cause the piston connecting rod to bend, and in severe cases, damage the engine block, leading to irreparable harm. 2. No Compensation from Insurance Companies: Any damage caused by restarting the engine after water intake will not be covered by insurance. Moreover, attempting to restart the engine after water intake is a serious violation of insurance claim principles, making the claim ineligible. In such situations, the first course of action should be to push the vehicle out of the water, then call for roadside assistance or contact a nearby repair station to have the vehicle towed away for inspection and repairs.

6

4

Share

Why does the display screen remain on after removing the car key?

There are two main reasons for this issue: first, the key switch may be faulty, causing the vehicle to remain in the power-on position without completely turning off the electrical appliances. Second, the power supply of the central control screen may be malfunctioning, preventing it from automatically shutting off. More relevant information is as follows: 1. Damaged central control screen power supply: If the central control screen does not turn off, it might be due to a damaged power supply, which requires immediate attention. Otherwise, the vehicle may fail to start the next day due to battery drain. 2. Five numeric dots appear on the central control screen: These dots are actually part of the screen calibration process and do not indicate damage to the vehicle. After prolonged use, the touch points on the screen may become less responsive, prompting the system to automatically display a "Screen Calibration" page. Simply tap the five dots on the screen in order, and the system will automatically calibrate the screen. After calibration, the touch points will return to normal. If the central control screen becomes unresponsive, you can also manually enter the screen calibration program to correct it.

6

2

Share

Which button is the defogger in the car?

What Causes the Abnormal Noise After Clutch Replacement?

Is an Engine Not Being Broken Not Considered a Scrapping Standard?

Is a slightly deformed small car wheel hub a big problem?

Are There Motorcycles Equipped with Air Conditioning?

Can the Engine Be Restarted After Water Intake?

Why does the display screen remain on after removing the car key?

Is Automatic Transmission Subject 2 or Subject 3 Harder?

Can the ETC be directly transferred to a new car when selling the old one?

Does the Number of Passengers Include the Driver?

Why don't the brake lights come on when the headlights are on?