Which Button is for Hill Start Assist?

1 Answers
VonHaven
07/30/25 12:24am
The button for Hill Start Assist is the ESP button. If the ESP on the vehicle remains turned on, the Hill Start Assist function is also enabled by default. The Hill Start Assist system, abbreviated as HAC, is a feature derived from the ESP system. It allows the vehicle to maintain braking for a few seconds when starting on a slope without using the handbrake, even after the driver's right foot leaves the brake pedal. This provides the driver with enough time to smoothly transition their foot from the brake to the accelerator, preventing the vehicle from rolling backward and causing an accident. When a car is not equipped with Hill Start Assist Control, the driver must quickly and accurately switch from the brake pedal to the accelerator pedal.
Was this review help?
12
0
Share
More Forum Discussions

What are the symptoms of a faulty steering gear in large vehicles?

Large vehicle steering gear failure manifests as follows: Abnormal steering wheel noise: There is unusual noise when turning the steering wheel while stationary. Loose or heavy steering wheel: The steering wheel is either excessively loose during turns or extremely difficult to rotate. Difficult steering: Typically caused by power steering pump failure, making steering challenging. Maintenance tips for mechanical steering gears: Reduce speed when driving on rough roads to minimize the load on the steering gear. Regularly inspect the protective covers on both sides of the steering gear and the condition of the cover connecting the upper part of the steering gear to the universal joint cross shaft. Damaged covers are the primary cause of early wear and failure in steering gears. Once the cover is damaged, water, dust, and sand can enter the steering gear, disrupting the lubricating grease film on the gear rack and leading to internal rust and abnormal wear.
8
1
Share

What is the Vehicle Environmental Protection List?

Definition: The full name of the Environmental Protection List is the Vehicle Environmental Protection Information List. According to the requirements of the Ministry of Environmental Protection's 'Announcement on the Disclosure of Environmental Protection Information for Motor Vehicles and Non-Road Mobile Machinery', starting from January 1, 2017, motor vehicle manufacturers and importers must disclose key environmental protection information in the form of a 'Vehicle Environmental Protection Information List' before the product leaves the factory or the goods enter the country. Notes: All parallel imported vehicles with complete documentation will come with an Environmental Protection List. The Environmental Protection List may either be on the back of the conformity certificate or a separate document. Having an Environmental Protection List does not necessarily mean the vehicle is environmentally disclosed.
8
0
Share

How long after driving a cloned vehicle can a revoked driver's license be retaken?

Driver's licenses revoked due to vehicle cloning must wait two full years before reapplying. Regulations on driving cloned vehicles: There are no specific regulations requiring license revocation for driving cloned vehicles. Using another vehicle's motor vehicle registration certificate, license plate, vehicle license, inspection compliance mark, or insurance mark will result in confiscation by the traffic management department of the public security authority, along with impoundment of the vehicle. Retaking after revocation: If the revocation notice specifies three or five years, one must wait until that period ends before reapplying. If no time limit is specified, the revocation is immediate, allowing one to apply for a new driver's license after a few days.
9
1
Share

Will points be deducted for crossing the line after turning?

It depends. If you cross the line before the red light turns on, you will definitely be penalized with 6 points. However, if you cross the line after the red light turns on, no points will be deducted, but you must stop immediately. Penalty regulations: Vehicles that change lanes arbitrarily or cross solid lines at traffic light intersections can easily cause minor traffic accidents. If caught by "electronic police," a fine may be imposed along with a 3-point deduction. Additionally, if drivers fail to pay attention to road traffic markings and vehicles arbitrarily cross solid yellow lines to drive in the opposite direction, they may be fined and penalized with 3 points. Lane driving notes: If a vehicle does not drive in the designated lane—for example, if it is supposed to turn left in the left-turn lane but suddenly chooses to go straight—a fine and a 2-point deduction may also be imposed.
12
1
Share

What do the numbers on the barcode of a new car key represent?

This barcode is primarily used for key matching, essentially serving as a "plaintext" password-like data (or the vehicle's ID card). The purpose of the barcode: Individuals should keep it safe. If the car owner loses the key and needs to get a replacement, this barcode is required. The 4S store can use the barcode to retrieve some of the vehicle's password information, which is relatively straightforward. If this barcode is lost: It can be matched via another key (after-sales service); If all keys are lost (including the barcode), an application can be made through after-sales service (such as using a security code). Once the rematching is completed, the previously lost key will become invalid.
18
0
Share

Which Wheel Does Belt Slippage Start From?

Belt slippage starts from the smaller pulley (it mostly occurs on the smaller pulley) because the wrap angle of the smaller pulley is smaller than that of the larger pulley. The wrap angle refers to the arc length over which the belt rolls on the pulley. Introduction to elastic slip: Elastic slip is a normal and unavoidable phenomenon caused by the elastic deformation of the belt material, which leads to deformation under force. Slippage is a failure mode of belt transmission, reducing transmission efficiency. It occurs when the force exerted on the belt exceeds its ultimate tensile strength. Reasons for belt slippage in automobiles: Slippage occurs on the smaller pulley due to the calculation formula for the minimum initial tension. The formula shows that the smaller the wrap angle, the greater the required initial tension. Generally, the smaller pulley has a smaller wrap angle, so it requires a higher minimum initial tension. When the initial tension is less than this minimum, slippage occurs.
16
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.