Which brand does the Alphard belong to?

How to Drive an Automatic Car Without a Handbrake?

Automatic cars without a handbrake use a foot brake instead. The foot brake is located near the position of the left foot, similar to where the clutch would be in a manual transmission car, but slightly further to the left. Pressing it down firmly acts like pulling the handbrake, and pressing it again will release it automatically, similar to releasing the handbrake. In addition to handbrakes and foot brakes, some high-end automatic models are equipped with electronic parking brakes (auto-hold function). Here is additional information: 1. Parking Brake: Commonly known as the handbrake, its function is to provide resistance to prevent the car from rolling when parked. The parking brake, whether a handbrake or the parking gear in an automatic transmission, locks the drive shaft or rear wheels. The force applied by the parking brake is much weaker than that of the service brake, just enough to prevent the car from rolling on a slope. 2. Electronic Parking Brake System: This system integrates the temporary braking during driving with the long-term braking function after parking, and achieves parking braking through electronic control. The electronic parking brake uses electronic control to achieve parking braking, with the same working principle as the mechanical handbrake—both rely on the friction between the brake disc and brake pads to control parking braking. The only difference is that the control method changes from a mechanical handbrake lever to an electronic button.

15

5

Share

What Happens If a Car Doesn't Have an Air Filter?

If a car doesn't have an air filter, dust and sand can be sucked into the combustion chamber, causing valve wear and leakage, insufficient cylinder pressure, and power loss. It also accelerates wear on the cylinder liner, piston, and piston rings, leading to increased gaps and oil burning. Below are the impacts of not replacing the air filter. Engine Wear: It accelerates engine wear and carbon buildup. If the vehicle is driven without an air filter, dust directly enters the cylinder and mixes with the fuel-air mixture for combustion. This results in cylinder wear eight times greater than in vehicles with an air filter, piston wear three times greater, and piston ring wear nine times greater. Dirty Engine Intake: Long-term use of a damaged air filter allows dust not only to enter the engine but also to invade the engine's intake tract, making it dirty. Decreased Filtration Efficiency: If the air filter isn't too dirty, it can be cleaned with an air gun. When blowing, ensure to blow from the inside out. However, most air filters are made of coarse filtration, low-air-resistance materials. During driving, the filter creates resistance to airflow. When dust accumulation exceeds a certain level, the filter's resistance increases, and filtration efficiency decreases.

14

4

Share

What is the appropriate tire pressure for the Arrizo 5?

The normal tire pressure range for the Arrizo 5 is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and reduced by 0.1 bar in summer. To check the current tire pressure of the Arrizo 5 during daily driving, you can activate the tire pressure monitoring system, and the tire pressure values will be displayed on the central LCD screen of the instrument panel. The specific method is to press the LCD adjustment button on the left combination meter of the steering wheel to switch to the tire pressure monitoring system interface. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no stamp on top, four small spikes at the bottom, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure. The system usually alerts when the pressure is below 1.8 bar or above 3.0 bar. In this case, tire inspection and pressure adjustment are required. The tire pressure monitoring system has not been reset. After inflating the tires, if the tire pressure is not reset promptly, the system will still record the previous data, causing the tire pressure monitoring indicator to light up. Simply reset the tire pressure to resolve this issue. Damaged tire pressure sensor. The tire pressure sensor, which monitors tire pressure, is installed inside the tire and connected to the tire inflation valve. If the sensor is damaged during driving, it can also trigger the tire pressure warning light. For sensor damage, the only solution is to replace it with a new part.

1

Share

What are the effects of water in engine oil on the engine?

Water in engine oil can cause emulsification, reduce the viscosity of the oil, and significantly diminish its lubrication effectiveness. Ultimately, the engine suffers the damage. Water entering the engine is absolutely a fatal internal injury for a car. Once water enters the car engine, at best, the spark plugs may fail to ignite or the engine may stall directly; at worst, it could lead to cylinder explosion. If the engine only mixes with water vapor entering from the air filter, the problem is not serious and can be resolved with simple measures. Just clean the water vapor from the air filter, throttle valve, and cylinder. If a considerable amount of water enters the engine but does not affect normal driving, though the noise may be louder, it may indicate a small amount of water in the engine oil or gasoline. In this case, replacing the engine oil and cleaning the related engine components is necessary. If the engine has already taken in water, rather than just mixed with a lot of water, but the car has not been started and the engine has not been damaged, the water needs to be drained completely, the interior cleaned thoroughly, reassembled, and the engine oil replaced. However, the electrical system may not be entirely safe. Engines are classified into external combustion engines and internal combustion engines. An external combustion engine means its fuel burns outside the engine, while an internal combustion engine means its fuel burns inside the engine.

8

4

Share

What to Do When Driver's License Information Cannot Be Found on 12123 Filing?

12123 filing cannot find driver's license information, which mostly occurs in cases of cross-regional license renewal or replacement, change of issuing location, or system synchronization issues. Below are the solutions: 1. Replace the driver's license: After replacing the driver's license, the file number may also change. At this time, you need to go to the vehicle management office to confirm whether the file number has changed. If it has changed, use the new file number for filing. 2. Inconsistency between the registration location and the issuing location of the driver's license: If there is no change, it is likely due to the inconsistency between the registration location of the 12123 account and the issuing location of the driver's license. At this time, you need to cancel the 12123 account and register again. When selecting the registration location, choose the city or region consistent with the issuing location of the driver's license. After successful registration, re-file the information. 3. System not synchronized: If the above two methods do not work, it is mostly due to the system not being synchronized. Because the data on 12123 needs to be gradually synchronized between regions and provinces, this takes some time. Generally, in about 1-2 months, you can refresh your personal information on the 12123 platform for filing, or call the vehicle management office for consultation. As long as the vehicle management office can find it, there is no problem with the driver's license. At this time, you just need to wait patiently.

1

2

Share

What are the symptoms of severely worn brake pads?

It can lead to extended braking distance, abnormal brake noises, and brake shudder or vibration. Below is relevant information about brake pads: 1. Concept of brake pads: Automobile brake pads, also known as automobile brake linings, refer to the friction linings or blocks fixed on the brake drum or brake disc rotating with the wheel. These friction components bear external pressure and generate friction to achieve the purpose of vehicle deceleration. 2. Structure of brake pads: The heat insulation layer is composed of non-heat-conductive materials, serving the purpose of heat insulation. The friction block consists of friction materials and adhesives. When braking, it is pressed against the brake disc or brake drum to generate friction, thereby achieving the purpose of vehicle deceleration and braking.

12

3

Share

Which brand does the Alphard belong to?

How to Drive an Automatic Car Without a Handbrake?

What Happens If a Car Doesn't Have an Air Filter?

What is the appropriate tire pressure for the Arrizo 5?

What are the effects of water in engine oil on the engine?

What to Do When Driver's License Information Cannot Be Found on 12123 Filing?

What are the symptoms of severely worn brake pads?

What are the consequences of not changing the clutch fluid for a long time?

What are the reasons for increasing car fuel consumption?

Symptoms of a Damaged Clutch Cable?

What Transmission Does the Baojun 530 Use?