Where to Replace the Toyota Corolla Driveshaft Dust Cover?

Will the speed of an automatic transmission car decrease if the accelerator is not pressed?

Will the speed of an automatic transmission car decrease if the accelerator is not pressed? The reasons for the speed decrease when not pressing the accelerator and the speed without pressing the accelerator are as follows: Reasons for speed decrease when not pressing the accelerator: When an automatic transmission car reaches a certain speed, releasing the accelerator will cause the speed to drop rapidly. If the accelerator is not pressed continuously, the vehicle will eventually stop. All vehicles rely on fuel to maintain normal operation. Speed without pressing the accelerator: For ordinary automatic transmission cars, there is an idle forward speed in the D gear position, which is approximately 5 kilometers per hour. Different models may have slight variations, and it is also related to tire pressure. Higher tire pressure may result in slightly faster speed, while lower tire pressure, due to better grip, may result in slightly slower speed. This refers to flat road conditions or in urban traffic. In situations like traffic jams where the car moves slowly, there is no need to press the accelerator, and the car can move forward slowly using the engine's idle traction.

19

4

Share

Is it okay to park an automatic car without shifting to P gear?

Automatic cars must be shifted to P gear when parking. The correct steps and precautions for parking a car are as follows: Correct steps for parking a car: First, use the foot brake to stop the vehicle, then shift the gear from D to N, engage the handbrake, release the foot brake, and turn off the engine. Then, press the foot brake again, shift the gear from N to P, release the foot brake, and turn off the power to remove the key. This is the safest and most reliable parking method. Although it may sound complicated, it is the least harmful to the car. Precautions for parking: Do not turn off the power immediately after stopping the engine. The purpose is to confirm whether the vehicle is completely stationary under the handbrake condition; otherwise, accidents may occur.

14

1

Share

What are the hazards of abnormal tire pressure?

A car tire pressure of 2.0 bar is abnormal. The normal tire pressure range is between 2.2 to 2.8 bar. In winter, it should be appropriately increased by 2.0 bar, while in summer, it should be reduced by 1.0 bar. Hazards of overinflated tires: Tire friction and adhesion will decrease, affecting braking performance; it can cause steering wheel vibration and deviation, reducing driving comfort; it accelerates wear on the central tread pattern of the tire, shortening tire lifespan; vehicle vibration increases, indirectly affecting the lifespan of other components; it causes excessive stretching and deformation of tire cords, reducing tire elasticity and increasing the load on the car during driving; puncture resistance decreases. When encountering sharp objects like nails or glass on the road, the tire is more likely to be punctured, leading to internal cracks, blowouts, and tire bursts. Hazards of underinflated tires: Friction with the road surface increases, leading to higher fuel consumption; it makes the steering wheel heavy and prone to deviation, creating unsafe driving conditions; it increases the movement of various parts of the tire, causing abnormal heat due to excessive rolling; it reduces the functionality of the cords and rubber, leading to delamination or cord breakage, as well as excessive friction with the rim, causing damage to the bead area and abnormal wear; friction between the tire and the ground multiplies, rapidly increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may result in tire bursts; it increases tire deformation, making the sidewalls prone to cracks, generating flexing motion that causes excessive heat, accelerating rubber aging, cord fatigue, and breakage, while also increasing the tire's contact area with the ground and accelerating shoulder wear.

12

1

Share

Which Gear to Start an Automatic Transmission Car?

An automatic transmission car can be started in either P (Park) or N (Neutral) gear. The correct steps to start an automatic transmission car and the reasons for not directly shifting into D (Drive) gear are as follows: Correct steps to start an automatic transmission car: First, turn on the power (without starting the engine), press the brake, shift gears (not directly into D gear, but shift to N gear first, then ignite), then shift from N gear to D gear, release the handbrake, lift the foot brake, and start moving. Reasons for not directly shifting into D gear: This avoids the brief reverse impact on the transmission when starting in P gear, as it requires passing through R (Reverse) gear. Note that if you start in P gear and want to avoid this brief impact, you can also shift directly from P gear to D gear.

11

4

Share

Will an Automatic Transmission Vehicle Roll Back Without Hill Start Assist?

An automatic transmission vehicle will not roll back without hill start assist. As long as the slope is not too steep and the driver is proficient in operation—quickly pressing the accelerator pedal after releasing the brake pedal—the vehicle will not roll backward. The function and usage of the hill start assist system are as follows: Function of Hill Start Assist System: Hill Start Assist, also known as Hill-start Assist Control, temporarily applies braking force to all four wheels (for up to approximately 2 seconds) to prevent the vehicle from rolling backward when starting on an uphill slope. How to Use the Automatic Transmission Hill Start Assist System: When the vehicle's gear is not in P (it can be in any other gear), firmly press the brake pedal until you hear a "beep" sound. At this point, the hill start assist system activates (operating for two seconds), and the brake lights will illuminate to automatically generate braking force.

14

3

Share

Can You Still Drive If the 48V Mild Hybrid System Fails?

48v mild hybrid system failure still allows driving, as the vehicle is equipped with a 12-volt battery in the engine compartment that can be used in such cases. Below is an introduction to the 48V mild hybrid system: 1. Definition of the 48V Mild Hybrid System: The 48V mild hybrid system was first proposed jointly by Audi, BMW, Daimler, Porsche, and Volkswagen in 2011 as a replacement for the commonly used 12V electrical system in vehicles. Due to its outstanding advantages in emission reduction and cost-effectiveness, the 48V mild hybrid system has become one of the mainstream emission reduction technologies for traditional fuel-powered vehicles. In simple terms, the 48V mild hybrid system is an upgraded version of the 12V electrical system. 2. Function: The 48V mild hybrid is not a plug-in hybrid and does not require separate charging. Plug-in hybrid vehicles offer better acceleration performance compared to conventional hybrid vehicles and can rely on pure electric mode for longer distances.

16

1

Share

Where to Replace the Toyota Corolla Driveshaft Dust Cover?

Will the speed of an automatic transmission car decrease if the accelerator is not pressed?

Is it okay to park an automatic car without shifting to P gear?

What are the hazards of abnormal tire pressure?

Which Gear to Start an Automatic Transmission Car?

Will an Automatic Transmission Vehicle Roll Back Without Hill Start Assist?

Can You Still Drive If the 48V Mild Hybrid System Fails?

Can I skip driving practice two days before the Subject 2 test?

Is simulator training mandatory?

Why Can't the Automatic Transmission Shift from 5th to 6th Gear?

Why Do Automatic Cars Have Three Pedals?