Where to replace the side skirts of the 2021 Honda Spirior Classic?

What are the reasons for a car suddenly stalling while driving?

There are several reasons why a car may suddenly stall while driving: 1. Electrical circuit failure: Stalling due to low-voltage power interruption during driving, mainly check the ignition and starter switches as well as the fuse box. 2. Stalling caused by a short circuit in the low-voltage line. 3. Component failure: Usually, issues with the ignition coil, capacitor, or electronic ignition module. 4. Fuel system failure: Damage to the fuel pump, fuel pipe rupture, clogged carburetor fuel inlet, or an empty fuel tank can all cause sudden stalling. 5. Ignition system problems or issues with the engine overheating anti-explosion system. 6. Driver's lack of proficiency leading to stalling, especially improper coordination between the throttle and clutch in manual transmission cars.

20

5

Share

Is It Normal for a Car to Shake Violently at the Moment of Ignition?

The reason for a slight shake at the moment of ignition is the cold start of the vehicle, which can sometimes cause minor vibrations. As long as the shaking is not too severe and does not last long, it is considered normal. However, persistent shaking is abnormal. Here are the general reasons for car ignition shaking: 1. Incomplete combustion of gasoline in the engine, resulting in insufficient power, or a stuck or clogged fuel injector. Most engine shaking is caused by insufficient fuel supply due to clogged or stuck fuel injectors, leading to power loss. 2. Aging spark plugs due to prolonged use can cause the electrode gap to widen, leading to insufficient ignition energy and poor gasoline atomization. Additionally, many modern cars have three- or four-cylinder engines, each with a spark plug. These spark plugs can also develop widened gaps, causing power differences between cylinders and resulting in vehicle shaking. 3. Excessive carbon buildup in the engine's intake manifold and valves, which may be caused by a dirty throttle body or too much carbon buildup in the fuel injectors and intake passages. During a cold start, carbon deposits can absorb some fuel, preventing it from fully entering the combustion chamber. This leads to unstable idling, and during a cold start, carbon deposits may absorb some gasoline, causing the air-fuel mixture in the engine cylinders to become too lean, resulting in engine shaking and difficulty starting.

17

1

Share

How to Test Engine Oil with Qualitative Filter Paper?

Use the oil dipstick to place 1-2 drops of engine oil in the center of the qualitative filter paper. Place the filter paper with oil drops on a flat surface, ensuring the back of the paper does not touch any object to avoid affecting the oil diffusion. Let it stand at room temperature for 0.5-1 hour, then observe the spot pattern. Additional information: 1. The purpose of the filter paper spot test method is to determine the clean dispersing performance of lubricating oil containing detergent-dispersant by observing its diffusion into spots on the filter paper. 2. The standard categorizes spot patterns into four grades. (1) Grade 1: The deposit ring and diffusion ring of the oil spot have no clear boundary; the entire spot is uniform in color, with a light and bright oil ring, indicating good oil quality. (2) Grade 1-2: The deposit ring of the oil spot is dark in color, the diffusion ring is relatively wide, and there is a clear boundary between the two rings. The oil ring appears in varying shades of yellow, indicating the oil is prone to contamination. Oil filtration should be enhanced, but the lubricating oil can still be used. (3) Grade 2-3: The deposit ring is dark black with dense deposits, the diffusion ring is narrow, and the oil ring darkens, indicating the oil quality has deteriorated. (4) Grade 3-4: The oil spot only has a central deposit ring and an oil ring, with no diffusion ring. The deposit ring is pitch black and thick, not drying easily.

4

1

Share

What are the reasons for no response when turning the key to start the car?

There are several reasons why the car does not respond when turning the key to start: 1. The ignition switch is not properly engaged or is damaged. 2. The wire from the ignition switch to the starter relay is disconnected. 3. The starter's fuse box is burned out. 4. The starter relay is damaged. 5. The starter is damaged. 6. The remote control is locked. 7. For automatic transmission, check if it is in the correct gear, and inspect the starter relay and motor issues. For manual transmission, check the clutch and ignition switch problems. Solutions are as follows: 1. First, check if the car battery has power by turning on the headlights to see if they light up. 2. Listen for sounds when starting. If there is no sound at all but a clicking noise, it indicates the starter solenoid is faulty. Replace the starter or the solenoid. 3. If there is no sound at all, it might be due to worn-out carbon brushes. You can replace the carbon brushes or the starter, but also check the fuse, starter relay, ignition switch, and starter, as these could also be the cause of the problem.

4

1

Share

What does engine horsepower mean?

Engine horsepower refers to the output capacity (work done) of the engine, which is the output power. Output power is the most important parameter for measuring vehicle performance and is used to evaluate engine performance. Horsepower, torque, and rotational speed are essentially three interrelated parameters. Additional information: 1. Horsepower is a commonly used unit of power measurement in engineering. It generally refers to metric horsepower rather than imperial horsepower. 2. Metric horsepower is a value very close to imperial horsepower. It is defined as the work required to lift 75 kilograms-force·meters in one second. That is: 1 metric horsepower = 75 kilograms-force·meters/second = 735 watts. 3. Some countries such as the United Kingdom and the United States use imperial horsepower. 1 imperial horsepower equals 550 foot-pounds/second, which is equivalent to 745.7 watts. In the late 18th century, British physicist James Watt (1736-1819) defined horsepower as the work required to lift 1000 pounds by 33 feet in one minute to measure the power of newly manufactured steam engines. This is imperial horsepower, represented by the letter HP.

14

2

Share

What are the impacts of not having a catalytic converter?

The following are the impacts on a vehicle without a catalytic converter: 1. The engine emission warning light on the combination instrument panel will illuminate, and the vehicle's exhaust emissions will severely exceed standards. 2. While driving on the road, the vehicle may be caught for violations and face penalties such as fines. 3. If the vehicle reaches the annual inspection period, it will fail the inspection. Additional Information: The catalytic converter is installed between the engine exhaust manifold and the muffler. It converts harmful gases such as CO, CH, and NOx produced by engine combustion into harmless carbon dioxide, water, and nitrogen through oxidation and reduction reactions within the catalytic converter's honeycomb-structured ceramics and precious metals. Since this converter can simultaneously transform three major harmful substances in the exhaust into harmless ones, it is called a three-way catalytic converter.

4

0

Share

Where to replace the side skirts of the 2021 Honda Spirior Classic?

What are the reasons for a car suddenly stalling while driving?

Is It Normal for a Car to Shake Violently at the Moment of Ignition?

How to Test Engine Oil with Qualitative Filter Paper?

What are the reasons for no response when turning the key to start the car?

What does engine horsepower mean?

What are the impacts of not having a catalytic converter?

What are the drawbacks of replacing 185 tires with 195 tires?

Can 0w40 engine oil be used in summer?

What to Do When Your Driver's License Exceeds the Six-Year Validity Period?

How to Test the Condition of a Car Battery?