Where to Renew Driver's License in Yiwu?

1 Answers
McAmelia
07/30/25 5:19am
Yiwu driver's license renewal is located in the Zongze North Road Auto City. The Yiwu Vehicle Management Office is situated within the Zongze North Road Auto City. According to regulations: Motor vehicle drivers can apply for license renewal at the vehicle management office that issued their original driver's license within 90 days before the expiration date. Below are the age requirements for applying for a driver's license: 1. For small cars, small automatic transmission vehicles, small automatic transmission passenger vehicles for disabled persons, or light motorcycles: Applicants must be between 18 and 70 years old. 2. For low-speed trucks, three-wheeled vehicles, ordinary three-wheeled motorcycles, ordinary two-wheeled motorcycles, or wheeled self-propelled machinery: Applicants must be between 18 and 60 years old. 3. For city buses, large trucks, trolleybuses, or trams: Applicants must be between 20 and 50 years old. 4. For medium-sized passenger vehicles: Applicants must be between 21 and 50 years old. 5. For tractor vehicles: Applicants must be between 24 and 50 years old.
Was this review help?
12
2
Share
More Forum Discussions

Does Turbocharging Save Fuel?

Turbocharged models do not save fuel; they simply deliver stronger power output. Here are the relevant details: 1. Overview: Compared to naturally aspirated engines of the same displacement, turbocharged engines consume slightly more fuel. Whether fuel is saved depends on the engine's thermal efficiency and power tuning, not the turbocharger. 2. Turbocharging Principle: Within the same unit of time, it forces more air-fuel mixture into the cylinder for compression and combustion. This allows for greater power output at the same RPM compared to naturally aspirated engines.
8
3
Share

How to Adhere Car Sealing Strips?

Clean the floating sand and dirt on the rubber surface to keep the bonding area clean. If conditions permit, you can slightly sand the rubber sealing strip. Unscrew the front cover to use. If there is glue at the bottle mouth, first wipe it clean with a cotton cloth, then you can put on the PE dropper for use. Apply glue to the bonding surface, then proceed with adhesion and maintain until it hardens.
4
5
Share

How to Add Engine Cleaner?

Pull out the fuel pump fuse, open the fuel tank cap, start the engine, and reduce the residual pressure in the fuel system. Insert the fuel system into the fuel pipe and connect it to the dedicated equipment on the fuel pipe. Close the valve on the fuel pipe and add the gasoline cleaner. After cleaning, the engine will automatically shut down. Disconnect the air source and eliminate the fuel pipe pressure. Remove the fuel pipe, reinstall the engine into the fuel pipe, replace the fuse and fuel tank cap, start the engine, and check if the fuel pipe connection is secure.
12
2
Share

How to Cleanly Remove Car Window Tint Film?

Lift a corner of the car window tint film, it is recommended to use your fingernail or adhesive tape to peel it off, and with the help of hot air from a heat gun or hair dryer, slowly remove the car window tint film. After removal, if there is any residual adhesive from the window film, clean it off with adhesive remover. There might be a glue odor after removing the window film, which can be eliminated by ventilation and sun exposure.
18
2
Share

What is the method to wake up a BYD Tang with a dead battery?

Open the driver's side door of the BYD Tang. Release the electronic parking brake switch of the BYD Tang. Press the brake pedal of the BYD Tang all the way down until it can't be pressed further, to prepare for starting the engine. Press the one-button start key of the BYD Tang. All the dashboard lights of the BYD Tang will illuminate, indicating that the engine has been successfully started.
14
0
Share

How to use the wipers on a GL8?

First, push the lever upward to activate a single wipe; pull the lever toward the driver to spray washer fluid and activate the wipers; Leave it in the first position for slow intermittent wipes; push the lever down to the second position for medium-speed wipes; Push the lever down to the third position for fast wipes; the switch in the middle of the control stalk adjusts the intermittent wipe speed across all three positions.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.