Where to Renew a Driver's License in Zhengzhou?

1 Answers
DelIris
07/29/25 3:31pm
In Zhengzhou, driver's license renewal is processed at the Vehicle Management Office. Below are important considerations for expired licenses: Legal provisions: According to the Road Traffic Safety Law, failure to renew a license for more than one year after its expiration will result in automatic cancellation of the motor vehicle driver's license; if it exceeds two years, the license can be restored to normal use after passing the subject one exam; if the cancellation period exceeds two years, the individual must reapply for a new license. Expired license: It is particularly important to note that driving a motor vehicle with an expired license is prohibited. Driving with an expired license is considered unlicensed driving or treated as such. Penalties for driving a motor vehicle include fines and may also involve detention for up to 15 days. In cases of serious traffic accidents resulting in casualties, criminal liability will be pursued according to the law.
Was this review help?
14
1
Share
More Forum Discussions

What Problems Can Excessive Engine Oil Cause?

Excessive engine oil can cause: 1. Reduced engine power output; 2. Blue smoke from the exhaust pipe; 3. Issues such as piston ring seizure and fuel injector clogging; 4. Crankshaft explosion; 5. Oil leakage; 6. Increased wear and reduced lubrication performance; 7. Oil degradation, affecting performance. Method to check oil level: Open the engine compartment, locate the small-ringed dipstick near the engine, pull it upward, and check if the oil mark is between the upper and lower lines. Engine oil is the lubricant used in engines, composed of base oil and additives, serving functions such as lubrication and wear reduction, auxiliary cooling, sealing and leak prevention, rust and corrosion protection, and shock absorption.
16
5
Share

What are the symptoms of a bad front wheel bearing in a vehicle?

Vehicle front wheel bearing failure symptoms are as follows: 1. When turning the steering wheel at a standstill or low speed, a "squeaking" sound is emitted, and in severe cases, steering wheel vibration can be felt. 2. Tire noise becomes noticeably louder while driving, and in severe cases, abnormal noises may occur. 3. A "thudding" sound can be heard when driving on bumpy roads or over speed bumps. 4. Vehicle deviation may also be caused by a damaged pressure bearing. Below are the repair steps: 1. After removing the tire, the car's brake disc and brake caliper can be seen. Remove them to access the front wheel bearing. 2. Use a flathead screwdriver to remove the dust cover on the outside of the bearing, revealing the large fixing nut. Remove the nut using a 30mm socket. 3. Use an 18mm open-end wrench to remove the two screws fixing the brake caliper, then carefully remove the caliper to avoid breaking the brake hose. 4. Remove the outer brake disc. If the brake disc is stuck, screw two bolts into the brake disc holes and tighten them with the corresponding wrench to remove the brake disc. 5. Once the outer securing nut of the bearing is removed, the bearing can be pulled out by hand. 6. Install the new bearing, replace the securing nut, and after tightening the nut, use a flathead screwdriver to rivet the edge of the nut for added security, then install the dust cover. 7. Reinstall the brake disc and brake caliper to complete the bearing replacement.
9
0
Share

Are Car Oil Filters Universal?

Car oil filters are not universal. The function of a car oil filter is to remove impurities, colloids, and moisture from the oil, delivering clean oil to lubrication points. Engine oil itself has high viscosity and contains a significant amount of impurities. To improve filtration efficiency, oil filters are designed with three stages. The types of oil filters are: 1. Oil suction filter: Installed in the oil pan before the oil pump, using a metal mesh type; 2. Oil coarse filter: Installed after the oil pump, connected in series with the main oil passage, mainly including metal scraper type, sawdust filter core type, and microporous filter paper type; 3. Oil fine filter: Installed after the oil pump and connected in parallel with the main oil passage.
20
4
Share

How to Operate the Chevrolet Cavalier with Manual and Automatic Transmission?

Here is an introduction on how to operate the Chevrolet Cavalier: 1. The 2020 Cavalier has 5 gear positions, which are P (Park), R (Reverse), N (Neutral), D (Drive), and L (Low). 2. After entering the driver's seat, fasten your seatbelt first and pay attention to the tachometer on the dashboard. When starting a cold engine, the engine speed is usually above 1000 RPM. Wait for about 10 seconds until the RPM drops below 1000. 3. When the RPM drops below 1000, press the brake pedal with your right foot and shift the gear from P to D. After shifting to D, slowly release the brake pedal with your right foot, then gently press the accelerator to gradually increase the vehicle speed. 4. Press the brake pedal, shift into first gear, and press the accelerator to reach 4000 RPM, then quickly release the brake. 5. If the engine speed is too high, the transmission will not immediately respond to the gear shift but will downshift after the RPM decreases. If the engine speed remains too high for a long time, the transmission will first increase the gear position on the dashboard by 1 and then attempt to downshift. In L gear, the transmission will not upshift beyond the gear position displayed on the dashboard but will downshift based on the vehicle speed to prevent stalling.
9
1
Share

Where are the brake and clutch pedals located in a car?

The brake and clutch pedals in a car are located as follows: 1. Clutch: Among the three pedals, the clutch pedal is positioned on the far left, closest to the driver's side door. 2. Brake: The brake pedal is located to the right of the clutch pedal, with the accelerator pedal being the rightmost pedal. Additional information about the brake and clutch is provided below: 1. Brake: The brake is a mechanical braking device designed to reduce the vehicle's speed, also known as a decelerator. Pressing the brake pedal activates the brake linkage, which applies pressure to the brake pads on the brake drum, gripping the brake disc to slow down or stop the vehicle. 2. Clutch: The clutch pedal can be depressed or released as needed to temporarily disconnect or gradually engage the engine from the transmission, thereby interrupting or transferring the engine's power input to the transmission.
2
3
Share

What is the 0-100 km/h acceleration time of the RAV4?

According to official data, the RAV4 comes with two engine options: 2.0L and 2.5L. The 2.0L model accelerates from 0-100 km/h in 12.49 seconds, while the 2.5L model does it in 10.58 seconds. Factors affecting a vehicle's 0-100 km/h acceleration time include: Torque: Torque represents the rotational force of the engine. Higher torque means greater force to propel the vehicle, resulting in faster acceleration. For example, the BMW X2 with 220 Nm of torque accelerates from 0-100 km/h in 9.6 seconds, while the RAV4 2.0L with 209 Nm takes 12.49 seconds. Transmission efficiency: The transmission acts as a medium for power delivery, inevitably involving power loss. Higher transmission efficiency leads to better acceleration performance. Generally, transmission efficiency ranks as follows: manual transmission > dry dual-clutch transmission > wet dual-clutch transmission > AT transmission > CVT transmission. The RAV4 2.0L is equipped with a CVT transmission. Power-to-weight ratio: The relationship between horsepower and vehicle weight is called the power-to-weight ratio (measured in Hp/T). A higher power-to-weight ratio results in faster acceleration. For instance, the BMW X2 with a 90 Hp/T ratio accelerates from 0-100 km/h in 9.6 seconds, while the RAV4 2.0L with a 111 Hp/T ratio takes 12.49 seconds.
14
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.