Where to Purchase Motorcycle Theft Insurance?

Why Can't the Automatic Transmission Gear Be Engaged?

The reasons why the automatic transmission gear cannot be engaged are: 1. Internal failure of the gearshift assembly; 2. Malfunction of the internal control module of the transmission; 3. Failure of the transmission gear position switch. An automatic transmission does not require the driver to manually shift gears; the vehicle will automatically select the appropriate gear based on the driving speed and traffic conditions. The steps to start an automatic transmission vehicle are: 1. After the driver sits in the driver's seat, press the start button directly; 2. Depress the brake pedal and press the start button to ignite and start the engine; 3. Release the foot brake and let the vehicle warm up in place; 4. Depress the brake pedal again and shift to D gear; 5. Release the handbrake and slowly release the foot brake to start the vehicle.

15

0

Share

How to Check an Automotive Electronic Voltage Regulator?

Automotive electronic voltage regulator inspection method is: 1. Connect the tester's positive terminal to the regulator's positive post, ground to the regulator's ground post, and use a wire to connect the field terminal to the carbon brush; 2. Use a test lamp to check if the carbon brush has power - if the bulb lights up, the electronic regulator is functioning normally; if not, it indicates damage. The working principle of an automotive electronic voltage regulator is: When the engine's output voltage becomes low or fails due to other reasons, the battery will generate current in the generator's windings. The electronic regulator then cuts off this reverse current to prevent excessive current in the motor windings from damaging the generator. The electronic voltage regulator is an alternator with intuitive charging indication and fault display functions.

7

4

Share

What are the reasons for severe carbon buildup in fuel injectors?

The reasons for severe carbon buildup in fuel injectors are: 1. Insufficient oxygen supply, which prevents complete combustion of the gas in the cylinder; 2. Frequent driving in congested road conditions, where fuel enters the combustion chamber but fails to burn completely. The fuel injector is located on the intake manifold of the direct-injection cylinder block, and its functions are: 1. To facilitate complete combustion; 2. To supply fuel to the engine. The working principle of a fuel injector is: When the electromagnetic coil is energized, it generates suction, lifting the needle valve and opening the injection hole. Fuel is sprayed at high speed through the annular gap between the needle valve head and the injection hole, forming a mist.

10

5

Share

How to Replace Refrigerant in a Car Air Conditioner?

To replace the refrigerant in a car air conditioner, follow these steps: 1. Evacuate the system and close the manual valves on the pressure gauge along with the high and low-pressure manual valves; 2. Connect one end of the hose to the injection valve fitting of the refrigerant canister; 3. Open the refrigerant canister, loosen the nut on the pressure gauge hose to allow some gas to escape, then close it; 4. Open the high-pressure side manual valve and invert the canister; 5. Inject the specified amount of liquid refrigerant, then close the refrigerant injection valve and the high-pressure manual valve. To determine if the car air conditioner lacks refrigerant: 1. If bubbles continuously appear in the sight glass during normal operation, it indicates insufficient refrigerant; 2. If no bubbles appear in the sight glass during normal operation but briefly appear when the air conditioner stops, it indicates the refrigerant level is normal.

9

5

Share

What are the symptoms of a faulty ABS pump?

When the ABS pump fails, the following symptoms may occur: 1. During emergency braking, the system cannot prevent wheel lock-up, posing a safety hazard; 2. The ABS warning light will illuminate, and the brake pads may fail to reset. The functions of ABS include: 1. Maximizing braking efficiency to reduce braking time and distance; 2. Effectively preventing vehicle skidding and fishtailing during emergency braking, ensuring good driving stability; 3. Allowing steering control during emergency braking for improved maneuverability. Common causes of ABS pump failure are: 1. Faulty ABS wheel speed sensors; 2. ABS wiring connection issues; 3. ABS control unit programming errors; 4. ABS master cylinder malfunction.

4

2

Share

What type of oil should the Kicks use?

The Kicks uses 0W20 engine oil. Engine oil, also known as engine lubricant, serves multiple functions including lubrication and wear reduction, auxiliary cooling, sealing to prevent leaks, rust and corrosion prevention, as well as shock absorption. The Kicks has the following dimensions: length 4295mm, width 1760mm, height 1588mm, with a wheelbase of 2620mm and a fuel tank capacity of 41 liters. It is equipped with a 1.5L naturally aspirated engine, delivering a maximum power of 90 kilowatts and a maximum torque of 143 Newton-meters. It is paired with a 5-speed manual transmission. The front suspension is of the MacPherson strut independent type, while the rear suspension is a torsion beam non-independent type.

8

2

Share

Where to Purchase Motorcycle Theft Insurance?

Why Can't the Automatic Transmission Gear Be Engaged?

How to Check an Automotive Electronic Voltage Regulator?

What are the reasons for severe carbon buildup in fuel injectors?

How to Replace Refrigerant in a Car Air Conditioner?

What are the symptoms of a faulty ABS pump?

What type of oil should the Kicks use?

What to Do When Engine Coolant Temperature is Too High?

Does It Matter If the Tread Patterns of the Rear Tires Are Inconsistent?

What Causes the Engine Fault Light to Illuminate and the Car to Shake?

How to Correct Late Steering When Reversing into a Parking Space?