···
Log in / Register

Where to Practice for Subject 3 Driving Test?

4 Answers
DeClayton
07/29/25 12:12am

Subject 3 requires practicing at a driving school, as you cannot drive without a license and must learn under the guidance of an instructor using a training vehicle. Introduction to Subject 3: Subject 3 is the road driving skills test, commonly referred to as the "road test." It includes numerous test items and requires attention to many details, making it one of the more challenging parts of the driver's license examination. Key Points for Subject 3 Test: Walk around the vehicle to ensure safety before getting in. Turn on the left turn signal when starting. For the light simulation, activate the corresponding lights within 5 seconds after the voice prompt. Brake in advance at: straight intersections, bus stops, crosswalks, school zones, left/right turns, U-turns, and when meeting oncoming vehicles. After the test, remember to turn off all lights. For safety, wait until you hear "Test completed, you passed" before unfastening your seatbelt.

Was this review help?
1
3
Share
LeHaven
08/12/25 3:24am

Last year when I took my driver's license test, the practice location for Subject 3 was at the driving school's training ground, which had a dedicated simulated road test area with very realistic setups like parallel parking spots, acceleration/deceleration lanes, and turning zones. The instructor took us there to practice several times a week, each session lasting most of the day, repeatedly practicing test items such as lane changes and light usage. The training ground is located at a designated site in the suburbs, with convenient transportation, no interference from other vehicles, and much higher safety standards. I recommend following the driving school's arrangements and not practicing on public roads privately—if an accident happens, it could be troublesome. Choose a driving school close to home, book time slots in advance, and stick to practicing an extra half-hour daily; accumulating experience will greatly improve your test pass rate. Remember the layout of the training ground—the exam setup will be identical, and familiarity can help ease nervousness.

Was this review help?
14
5
Share
Expand All
DelNaomi
10/01/25 7:02am

As a seasoned driver with years of experience, I recall that the practice for Subject 3 during my driving lessons took place in specialized areas approved by the traffic management authorities. These locations typically feature well-marked lines and electronic monitoring. For beginners choosing a practice site, selecting one closer to home saves time, and focusing on parallel parking and emergency handling—key elements in the test—is crucial. In terms of location, urban driving schools usually have multiple branches; choosing one near the test center is preferable, allowing you to familiarize yourself with the environment beforehand. Avoid practicing on public roads without authorization, as it not only risks fines but is also unsafe. Nowadays, many apps can help you find nearby training grounds, making it easy to book sessions—convenient and practical. Consistently practicing in a professional environment helps build a solid foundation.

Was this review help?
9
1
Share
Expand All
McLeo
11/15/25 2:02am

For the location of Subject 3 driving practice, it is essential to choose a safe and professional place. I recommend going directly to the driving school's designated training ground. These sites simulate real road test scenarios, reducing the risk of accidents. Practice content includes straight-line driving and lane-changing operations, so finding a flat and open area is crucial. Locations are usually near the driving school base or test center. Beginners should not practice on the road—it's dangerous and ineffective. Book a time slot and practice under the guidance of a coach for efficiency and peace of mind. Familiarize yourself with the layout of the venue before the test, such as the location of parking areas, to avoid on-site mistakes.

Was this review help?
16
4
Share
Expand All
More Forum Discussions

What is the function of a car front lip?

Most vehicle front lips serve only a decorative purpose. Installing a front lip can make the car look more aesthetically pleasing, but its practical effect is actually minimal—it merely adds a bit of personality to the vehicle's appearance. To avoid being stopped by traffic police, it's best not to modify it. Below is an introduction to the materials used for car front lip kits: 1. Introduction one: The cheapest option is resin fiber, also known as fiberglass. It is relatively brittle and has decent formability, but it is not suitable for automotive exterior kits. These items are very low-cost, so the surface finish is also poor. After purchase, you must apply putty and paint to cover imperfections. 2. Introduction two: A better option is commonly seen one-time molded PP material, which is ABS engineering plastic. This material has slight flexibility, but its elasticity is limited. It is heat-resistant and not prone to deformation, but it is relatively hard. The craftsmanship is better, giving it a high-end appearance, and it is generally used for small car kits or parts close to the ground. 3. Introduction three: Another commonly used material is PU, or soft rubber, which is highly flexible and resistant to scratches and damage. However, it cannot withstand high-temperature paint baking and is prone to deformation. It is also relatively thick and heavy.
13
3
Share

Should You Use Recirculation or Fresh Air Mode for Car AC Cooling in Summer?

Choose an appropriate temperature based on the heat level. Generally, selecting between 22°C to 24°C in summer provides relatively comfortable conditions. Regarding the use of recirculation and fresh air modes, it is recommended to use fresh air mode when needing to quickly lower the cabin temperature or ventilate the interior air. In other situations, recirculation mode can be selected. Below are more relevant details: Precautions: 1. Before using the AC in summer, ventilate the cabin air to expel hot air. The main method is to open doors on the same side or lower windows completely while keeping windows on the opposite side closed. By repeatedly opening and closing doors, hot air can be circulated and expelled. 2. Another method is to open all four windows or diagonally opposite windows while driving, which accelerates hot air circulation. When interior and exterior temperatures become similar, close windows, turn on the AC cooling function, set the air intake to fresh air mode, and adjust temperature to the lowest setting to accelerate cabin temperature stabilization. Once reaching the desired temperature, switch from fresh air to recirculation mode.
18
1
Share

What does AC on the car air conditioner mean?

AC on the car air conditioner is the cooling switch. When AC is turned on, the car compressor activates, and the air blown by the air conditioner becomes cold; if AC is not turned on, the car compressor remains off, and the air blown is natural. AC is the abbreviation for air conditioner, meaning air conditioning, and can also be understood as cold air. Relevant information about car air conditioners is as follows: 1. Introduction: The car air conditioning device (air-conditioning-device), referred to as car air conditioner. 2. Function: It is used to adjust and control the temperature, humidity, air cleanliness, and air flow inside the car compartment to the optimal state, providing a comfortable riding environment for passengers and reducing travel fatigue; it creates good working conditions for the driver and plays an important role in ensuring safe driving as a ventilation device.
17
3
Share

What are the requirements for changing from C1 to C2?

Changing from C1 to C2 must be handled by the driver in person. Before applying, it is necessary to verify that the applicant does not have 12 penalty points, overdue inspection, or a driver's license that is detained, suspended, revoked, or canceled. The following are the specific details: 1. C1 driver's license: The scope of C1 driver's license includes small and mini passenger cars, light and mini cargo trucks, and light, small, and mini special-purpose vehicles. The number of passengers in small passenger cars should not exceed 9. According to this standard, a C1 license cannot drive vehicles with more than 9 seats. The total length of the cargo truck driven should not exceed 6 meters. 2. C2 driver's license: The applicant must be between 18 and 70 years old. The permitted vehicle type is small automatic transmission cars. The permitted vehicles include small and mini automatic transmission passenger cars and light and mini automatic transmission cargo trucks. The test vehicle should be a light automatic transmission ordinary cargo truck with a length of not less than 5 meters, or a small automatic transmission ordinary passenger car with a length of not less than 4 meters, or an automatic transmission car with a length of not less than 4 meters.
13
0
Share

What are the differences between Baojun 310 and Baojun 510?

Baojun 310 and 510 have the following differences: 1. Price: The official price of the top-end Baojun 310 is lower. The top-end Baojun 510 is higher. 2. Overall body: The top-end Baojun 310: The body is shorter than the top-end Baojun 510. The top-end Baojun 310: The wheelbase is the same length as the top-end Baojun 510. 3. Overall configuration: The top-end Baojun 510: More abundant. The top-end Baojun 310: Not as abundant as the 510. 4. Power output: The top-end Baojun 510: More powerful. The top-end Baojun 310: Not as powerful as the 510. Extended information is as follows: Baojun: It is an independent automobile brand created by SAIC-GM-Wuling in 2010. The Baojun brand originates from the original meaning of 'Jun', which is a fine steed, and Baojun means people's most beloved fine steed. Baojun Automobile fully integrates the superior resources of SAIC, GM, and Wuling. Brand positioning: 'Reliable partner', with 'optimism and progress, steady and reliable, smart and confident' as the brand spirit, aiming to provide consumers with an automobile brand that 'has international standards and high reliability, low ownership and usage costs, maximizes customer value, and exceeds customer expectations'.
11
4
Share

What Causes Engine Shaking When Cold Starting?

Reasons for engine shaking during cold starts: 1. Severe engine carbon buildup: The most common cause of car shaking is excessive carbon deposits on the throttle valve or fuel injectors. When there's too much carbon buildup inside the engine, the gasoline sprayed by the cold-start injector gets largely absorbed by these deposits, resulting in an overly lean air-fuel mixture during cold starts. This makes ignition difficult - the engine only starts easily after the carbon deposits become saturated with gasoline. Once started, the gasoline adsorbed on the carbon deposits gets drawn into the combustion chamber by the engine's vacuum, making the mixture too rich. This alternating lean-rich mixture condition causes idle shaking after cold starts. Lower temperatures require more fuel for cold starts, making carbon deposits more likely to affect successful starting. 2. Ignition system issues: Check the condition of spark plugs, high-voltage wires, and ignition coils. Poor ignition system performance or weak spark plug firing can also cause severe shaking during cold starts. 3. Unstable fuel pressure: If you've already cleaned engine carbon deposits, flushed the throttle valve, replaced gaskets and spark plugs but still experience body shaking at idle, it's recommended to visit a 4S shop to check fuel supply pressure and the intake pressure sensor. Abnormal fuel pump pressure or faulty intake pressure sensor readings can both cause body shaking. 4. Aging engine components: Car shaking can also be related to worn engine mounts (also called rubber mounts). Engine mounts act as the engine's vibration absorption system, responsible for dampening minor vibrations during operation. If engine mounts fail, these vibrations get transmitted to the steering wheel and cabin, causing shaking at idle.
11
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.