Where to Look When Making a U-turn?

2 Answers
VonRiver
08/30/25 7:26am
When making a U-turn, you should look at the right rearview mirror. U-turn techniques: When making a U-turn, check the right rearview mirror. Once you can see the intersection below the right rearview mirror, turn the steering wheel to the right. Straighten the steering wheel when the car body is parallel to the road. When turning, if you need to make a sharp turn, try to turn the steering wheel all the way, and slowly straighten it after completing the turn. For a wide turn, gradually turn the steering wheel. Do not press the following three components when making a U-turn: Do not press the clutch when turning or making a U-turn: The purpose is to ensure the vehicle has sufficient power to complete the turn. A car encounters greater resistance when turning compared to driving straight. Pressing the clutch to let the car coast may not provide enough kinetic energy, and releasing the clutch after coasting can easily cause the car to stall. Therefore, avoid pressing the clutch when turning or making a U-turn. Do not press the brake when turning or making a U-turn: The car should already be in a lower gear and slowed down before entering the turn. The speed is sufficiently low during the turn, and pressing the brake at this point can easily cause the car to stall. Do not press the accelerator when turning or making a U-turn: Most family cars are front-wheel drive, which are prone to understeer. Increasing speed under understeer conditions will only make it harder for the car to complete the turn.
Was this review help?
9
2
Share
SanEliza
09/12/25 4:25am
When making a U-turn, I have to remind myself to take it slow, especially as a new driver. First, check the rearview mirror inside the car to see if any vehicles are approaching from behind—don't let them rear-end you. Then, quickly glance at the side mirrors on both sides to check for cars or motorcycles coming from adjacent lanes. Don’t rush the turn; always turn your head to confirm the blind spot, where pedestrians or shared bikes might be hidden from the mirrors and easily overlooked. Choose a wide road for U-turns, like an empty small intersection or a supermarket parking lot, and use your turn signal to alert others. At intersections, watch pedestrian signals to ensure no one is crossing; in rain or fog, turn on your headlights to illuminate farther ahead. Remembering these habits can prevent accidents—practice them a few times during daily driving to get used to them, but never speed through turns. Safety comes first; a little extra caution saves a lot of trouble.
Was this review help?
17
1
Share
Expand All
More Forum Discussions

What are the requirements for obtaining a Class A driver's license?

To obtain a Class A driver's license, the following requirements must be met: 1. Age: Between 26 and 50 years old. 2. Height: At least 1.55 meters tall for large vehicles. 3. Residence: Must study in the place of residence (within the prefecture-level city of household registration), and cannot study in a temporary residence. If the original driver's license is from another location, it must be transferred back to the original place of residence for study. 4. Cannot directly obtain a Class A license; it must be acquired by upgrading from another license. For A1 and A2 licenses, a Class B license with at least 5 years of driving experience is required, and the driver must not have received full penalty points in the current year. For an A3 license, a C1 license with at least 3 years of driving experience is required.
20
4
Share

What does the military license plate 'sd' mean?

Military license plate 'sd' represents vehicles belonging to the Equipment Department of Shenyang Military Region. Below is detailed information about military license plate 'sd': 1. 'S' stands for Shenyang Military Region (now renamed Northern Theater Command), and 'D' represents Equipment Department. Therefore, this is a military vehicle belonging to the Equipment Department of Shenyang Military Region. 2. White license plates starting with 'sd' indicate vehicles from the Equipment Department of Shenyang Military Region. White license plates are commonly seen on vehicles of national authority institutions such as public security departments, judicial departments, procuratorates, armed police forces, and PLA troops. 3. Military vehicle license plates serve as identification for all military vehicles nationwide. They are numbered plates with registration codes issued by the transportation department after reviewing, inspecting, and registering vehicles that apply for license plates. These plates serve as proof of special operating rights granted to military vehicles by the state.
17
2
Share

Mazda CX4 locked and unable to start?

There are many reasons why a car cannot start. If the car's anti-theft system malfunctions, it may be due to abnormal operation of the motor. Additional information: First, check whether the motor is operating normally. You can try using another battery to assist. If it operates normally, retrieve the engine anti-theft fault code to troubleshoot issues such as ignition cylinder pressure, fuel pressure, valve timing, and whether the exhaust pipe is clogged. Replace any damaged components. If the car is locked and unable to start, it is mostly due to a malfunction in the car's anti-theft system. It is recommended to visit a 4S shop for specialized handling. Note: Regular repair shops may not be able to resolve the issue, while 4S shops have specialized tools to reset the anti-theft system. The car's anti-theft system effectively protects the vehicle's security.
17
1
Share

How to Make DIY Automotive Body Filler?

Steps for preparing automotive body filler: 1. Purchase a can of polyester putty (also called body filler) as the base material from online stores or auto parts shops, then place an appropriate amount on a mixing board. 2. Add the hardener to the base material at a ratio of 100:2 to 100:3. Alternatively, high-concentration hide glue can be used as the hardener for polyester putty, as long as it can achieve curing. 3. Mix thoroughly until achieving a thick paste consistency before application. Two crucial precautions when preparing automotive body filler: 1. Strictly control the hardener quantity according to the mixing ratio. Otherwise, even with continuous stirring, achieving the desired paste consistency becomes difficult, which will significantly reduce the filler's adhesion and adversely affect subsequent painting processes. 2. The working time of polyester putty is limited (typically 10 minutes), so the mixing speed must be accelerated accordingly.
15
1
Share

Is Mazda Fuel-Consuming?

Mazda's fuel consumption is relatively high. Detailed information: The vehicle's self-weight is 1,284 kilograms, and it uses a 4A-type engine with relatively low transmission efficiency and low rotational speed, resulting in a fuel consumption of 8.5 liters per 100 kilometers. Additional information: Mazda is a Japanese brand headquartered in Hiroshima, Japan, with sales markets in Asia, Europe, and North America. It is the fourth-largest automobile manufacturer in Japan and a world-renowned car brand. Founded in 1920, by December 2018, it had ranked 242nd in the 2018 World's 500 Most Influential Brands. Its product lineup includes the Mazda2, Mazda3, Mazda5, and Mazda6. Among them, the Mazda6 made its debut at the 2001 Tokyo Motor Show as a mid-to-high-end sedan and has won over 30 awards in more than 20 countries.
14
4
Share

What is the first maintenance mileage for the Lynk & Co 01?

The first maintenance for this vehicle is due at one year or 10,000 kilometers, whichever comes first. Additional information: Change engine oil and oil filter (using the oil provided by the 4S store is sufficient); Clean the air filter and cabin air filter, check if brake fluid, antifreeze, and power steering fluid are lacking, and top up if necessary. Inspect the chassis components and suspension for any abnormal oil leaks or looseness (including tire pressure). Check if all lights are functioning properly. Inspect the wear condition of the brake pads. Measure the battery voltage to ensure it is normal. The above items are generally free of charge, and it is recommended to make an appointment in advance. All recommended items by the 4S store should be performed.
8
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.