Where to Look When 50 cm Away from the Side Car?

2 Answers
LaSilas
07/30/25 1:19am
Sit inside the car and find a reference point according to your own habits to locate a suitable spot. Additional information is as follows: 1. Introduction: A safe following distance refers to the necessary gap maintained by a trailing vehicle to avoid accidental collisions with the vehicle ahead while driving. Maintaining a safe distance is the most direct, effective, widespread, and fundamental method to prevent rear-end collisions. 2. Measurement Standard: There is no absolute standard for a safe following distance, only dynamic standards. The most direct and significant factor affecting the safe distance is speed. When the speed increases, the required braking force, braking distance, and the distance traveled at the original speed during the reaction time all increase accordingly. Maintaining a safe distance requires controlling the speed.
Was this review help?
10
5
Share
ORichard
08/15/25 6:57am
Someone once taught me a practical tip: sit upright and look at the lower left corner of your car's windshield. When the body of the adjacent car is about 10 cm above the lower left corner of your windshield, it's roughly 50 cm away. You can also check the highest protruding point of the right wiper—if it aligns with the bottom of the adjacent car's wheel, that's about the same distance. Remember to adjust your seat height properly and avoid leaning forward to check. This distance is especially important when changing lanes—too close risks a scrape, while too far affects the car behind. Practice a few times to get the hang of it.
Was this review help?
7
0
Share
Expand All
More Forum Discussions

How Long Can You Delay Handling a Red Light Violation?

After a vehicle runs a red light and is captured by electronic monitoring, the owner can check the violation record on the traffic website and then process it at the traffic police station where the violation occurred within one month before the vehicle's annual inspection. Additional information is as follows: General situation: After a traffic violation occurs, it generally takes 3 to 7 days to be visible online or for a notification SMS to be received, with a maximum delay of no more than 13 working days. Caught on the spot: If the violation is caught on the spot by a traffic officer and confirmed with a signature, the owner must process it at the local traffic police station within 15 days of the violation. If not processed within 15 days, a late fee of 3% per day will be charged, but the total late fee will not exceed double the original fine amount. Captured by electronic monitoring: If the violation is captured by electronic monitoring, the owner can check the violation record on the traffic website and then process it at the traffic police station where the violation occurred within one month before the vehicle's annual inspection. There is no need to process it within 15 days, but it is advisable not to exceed one driving license's scoring cycle to avoid accumulating 12 penalty points in the next cycle due to not clearing the points in time.
12
3
Share

Is it necessary to repaint a scratched bumper?

It is not necessary to repaint a scratched bumper. Additional information is as follows: Reasons why repainting is unnecessary: The bumper itself is made of plastic and will not rust. If the area of paint damage is too small, there is no need to repaint. It is better to wait until there are more scratches or until the bumper needs to be replaced. There are two scenarios for vehicle paint scratches: Minor scratches that do not expose the metal: It is recommended not to repaint. Repainting requires removing the existing paint layer, and the new paint may not match the color of the surrounding area, making the effort not worth it. Although minor scratches may look unsightly, they do not affect the vehicle's performance or safety. Severe scratches that expose the metal: In this case, repainting is essential. If left untreated, the exposed metal will begin to rust, especially after rain, leading to increasing rust damage. Eventually, the rust may penetrate the metal, requiring replacement of the entire body panel. Otherwise, water leakage and worsening rust will occur, leading to higher repair costs.
20
3
Share

How to Repair a Worn and Peeling Leather Steering Wheel?

The degree of wear on the steering wheel varies, and the repair methods will differ accordingly. Detailed instructions are as follows: Minor Wear: Purchase a bottle of specialized leather steering wheel repair fluid and apply it to the worn area according to the instructions. Small Cracks: If small cracks appear, apply acrylic resin to the cracks, align the edges, and dry them with the cold air setting of a hairdryer. Large Tears: If there is a tear, cut a piece of non-woven fabric slightly larger than the tear, place it underneath the damaged area, and apply leather adhesive. Then, lay a piece of cotton cloth over the damaged area and press it flat with an iron. Once the leather sets, remove the cotton cloth. If the crack is noticeable, apply a color paste that matches the original color. Unable to Repair Yourself: If you encounter a situation where you cannot repair it yourself, you will need to take it to a professional car detailing service to refurbish the steering wheel. Refurbishing techniques can maximize the repair of the worn areas.
4
1
Share

How to Operate Gear Shifting?

By pressing the brake, you can quickly downshift to decelerate. By releasing the accelerator, the engine speed of an automatic transmission vehicle will decrease, allowing the transmission to automatically recognize and subsequently downshift progressively to reduce speed.
17
4
Share

How to start a Yamaha motorcycle?

Turn on the power with the key, hold the brake + press the start button. Turn on the power with the key, hold the clutch + press the start button. If it's a carburetor model, you can also turn on the power and then kick the starter lever hard.
19
4
Share

How to Identify the Model and Specifications of Motorcycle Shock Absorbers?

Rear shock absorbers need to be distinguished between single shock and dual shock types. The spring wire diameter for single shock absorbers is thicker at 7.5mm, while dual shock absorbers use thinner 6mm spring wires. Pay attention to the distance between the upper and lower mounting holes, meaning the length must be appropriate.
8
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.