Where to Install Car Door Anti-Collision Strips?

1 Answers
StAndrew
07/30/25 9:46am
Car door anti-collision strips are installed on the protruding corners of the vehicle. Made of rubber or natural rubber, these strips are part of the exterior trim and primarily protect the car body from minor scratches and damage to components. The installation steps for car door anti-collision strips are as follows: 1. Open the car door and locate the protruding areas prone to collisions; 2. Wash the car with water and dry the area where the strip will be applied with a towel; 3. Slowly peel off the backing adhesive; 4. Align the strip and press gently to ensure full adhesion to the car surface; 5. Avoid washing the car within 48 hours after installation to prevent the adhesive from losing its bonding strength due to moisture.
Was this review help?
13
2
Share
More Forum Discussions

What is the beginning of Jiangning license plate numbers?

Jiangning license plate numbers begin with Su A. Motor vehicle license plate numbers consist of the motor vehicle registration authority code and the license plate number. The motor vehicle registration authority code consists of two characters, a Chinese character and an English letter. Additional relevant information is as follows: 1. The first character of the license plate is a Chinese character: it represents the provincial-level administrative region where the vehicle is registered, which is the abbreviation of the (province, municipality directly under the central government, or autonomous region). 2. The second character of the license plate is an English letter: it represents the prefecture-level administrative region where the vehicle is registered, which is the letter code for the (prefecture-level city, region, autonomous prefecture, or league). Generally, the ranking is determined by the provincial vehicle management office based on the status of each prefecture-level administrative region: (the letter "A" is the code for the capital, provincial capital, or central urban area of a municipality directly under the central government, and the subsequent letters are not ranked in any particular order).
16
3
Share

Where is the air conditioning filter located in an older BMW 3 Series?

The air conditioning filter in an older BMW 3 Series is located in the following position: 1. Near the driver's side footwell, there is an engine hood release lever. Pull it twice to unlock the engine hood. 2. Then, lift the lever at the front of the engine hood to open it. 3. Use the hydraulic strut to support the engine hood. 4. You will now see the layout of the BMW X3 engine compartment. 5. On the left side of the engine compartment, below the windshield, you will find the air conditioning filter housing. 6. To replace it, locate the area where the air conditioning filter is housed. Use a 10mm socket to remove the cover plate's fixing screws and take off the cover. Disconnect the power supply. Use a T20 screwdriver to remove the two fixing screws on the air conditioning cover plate and take it off. Remove the old filter and replace it with a new one. When replacing, note: the black side should face the rear of the car, and the arrow should point toward the front of the car. Bend the filter slightly for installation.
9
3
Share

What brand does Lexus belong to?

Lexus belongs to the Toyota brand. Here is the relevant introduction: 1. The models under the Lexus brand include: Lexus LM, Lexus UX300e, Lexus ES, Lexus RX, Lexus UX, Lexus CT, Lexus HS, Lexus IS, Lexus GS. 2. The Lexus UX is an urban SUV. The front and rear fenders of this car are tightly integrated with the body shape, extending outward and backward from the spindle grille, enveloping the entire vehicle. The hood and bumper are seamlessly combined with the headlights and spindle grille. The Lexus UX also features multiple innovative aerodynamic designs, further enhancing vehicle stability.
20
5
Share

What Are the Reasons Why a Scooter Has Electricity and Fuel but Fails to Start?

The reasons and solutions for a scooter having electricity and fuel but failing to start are as follows: Gasoline leakage or evaporation: It is recommended to check the fuel, replace the battery, then kick-start several times before turning on the ignition switch to start. Low idle speed: Sometimes the scooter fails to start due to low idle speed. Normally in summer, the speedometer needle should point to one mark or slightly more, while in winter, it should be adjusted to between one and a half to two marks. Spark plug failure: Replacing the spark plug can solve the issue. Check if there is oil on the spark plug head; oil indicates a faulty spark plug that needs replacement.
16
1
Share

What Does Motorcycle Idle Speed Mean?

Motorcycle idle speed refers to the engine's rotation speed when it is running without throttle input. Below are specific details about idle speed: Introduction: Idle speed describes an operational state where the engine runs without load, meaning the motorcycle is in neutral gear. The rotational speed during this state is called idle speed. The idle speed can be adjusted by modifying parameters such as the throttle opening size. Essentially, idle speed represents the engine "producing power without doing work." Condition: When the engine is running and the throttle grip is fully released, the engine enters idle state. During idle speed adjustment, the RPM should not fluctuate abruptly, as this may cause premature wear to the engine.
18
1
Share

What does an exclamation mark inside a bracket indicate as a fault?

Red exclamation mark (specifically in the form of an exclamation mark inside a circled bracket) represents a warning for the braking system, mainly indicating a fault in the braking system or low brake fluid level. Solution: Immediate inspection and repair of the braking system is required to avoid accidents. Apart from the red exclamation mark indicating a braking system fault, other exclamation marks on a car are yellow, representing general faults, automatic transmission faults, abnormal tire pressure, and lighting faults. Below is a detailed analysis of these four scenarios: General Fault: An exclamation mark inside a triangle indicates a fault in the car's general performance, components, or functions. This could include parking sensor failure, fuel cutoff system intervention or failure, external light failure, engine oil pressure sensor failure, etc. It is necessary to visit a 4S shop for inspection to identify the source of the fault. Automatic Transmission Fault: An exclamation mark inside a yellow gear is the automatic transmission fault warning light, indicating a fault in the transmission or transmission lubricant level below the normal range. Transmission fluid should be replaced promptly. Abnormal Tire Pressure: An exclamation mark below a horizontal line inside a bracket represents the tire pressure monitoring warning light. This light turns on when the tire pressure is too low. Check the car's tire pressure and restore it to the normal range. Lighting Fault: A yellow bulb with an exclamation mark is the lighting fault indicator, signaling a fault in the car's lights. Solution: Visit a 4S shop for inspection and repair as soon as possible, or conduct a self-check focusing on commonly used bulbs such as turn signals, fog lights, and interior lights to identify the issue.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.