Where to Inspect Vehicle CNG Tanks in Lanzhou?

2 Answers
VonGeorge
07/23/25 11:30pm
In Lanzhou, vehicle CNG tank inspections are conducted at the Special Equipment Inspection and Research Institute in the vehicle's location and authorized inspection points by the vehicle management office. Below is relevant information about converting vehicles to natural gas: 1. Introduction: Converting vehicles to natural gas (Car oil to gas) is a modification method that changes the fuel type of motor vehicles. It refers to the process of converting vehicles originally using fuel oil to burn natural gas. 2. Advantages: Higher economic benefits. Natural gas easily mixes with air in the engine, burns more completely and cleanly, is less prone to carbon deposits, has good anti-knock performance, and does not dilute lubricating oil, thereby greatly reducing wear on engine cylinder components and extending engine life and lubricant usage duration.
Was this review help?
6
3
Share
DelReed
08/10/25 7:24pm
I've been driving a gas-powered car in Lanzhou for several years. For the annual inspection, I usually go to qualified testing centers like the Vehicle Inspection Center in Beilongkou, which is quite reliable—I often go there for the procedure. Remember to bring your vehicle license, gas cylinder registration certificate, and ID card. The process includes a gas tightness test and an appearance check to ensure there are no cracks or corrosion on the tank. Lanzhou isn’t very large, and these inspection stations are usually located in Chengguan District or Qilihe. Before going, it’s best to check the specific address and book an appointment online to avoid long queues. Gas tank inspections are crucial—leaks can be dangerous. I recommend doing it on time every year and not delaying until it expires to avoid fines. Last time I neglected it, I had to spend extra time reapplying. Safety should always come first.
Was this review help?
6
1
Share
Expand All
More Forum Discussions

Should You Use Recirculated or Fresh Air Mode in Car AC?

When turning on the AC for cooling or heating, first activate recirculation mode to rapidly lower or raise the cabin temperature. Once stabilized, appropriately switch to fresh air mode for ventilation. The key difference lies in air intake - recirculation draws air from inside the cabin. Choose between modes based on these scenarios: 1. After parking under scorching sun when the cabin feels like a sauna, initially use fresh air mode with windows/sunroof open to accelerate heat dissipation. After 3-5 minutes when temperature stabilizes, close windows, activate cooling and switch to recirculation. 2. In extreme winter cold, delay heating until engine reaches normal operating temperature, then use recirculated heat for faster warming. 3. During traffic jams, prefer recirculation to avoid circulating polluted external air.
9
4
Share

Which country produces Acura?

Acura cars are produced in Japan. Here are the relevant details about Acura: 1. Acura is a premium sub-brand under Japan's Honda Motor Company, established in the United States in 1986. The name 'Acura' is derived from the Latin word 'Accuracy,' and its logo features a caliper used in engineering measurements, symbolizing Acura's exquisite craftsmanship and pursuit of perfection. 2. As the first Japanese luxury car brand, Acura redefined the concept of luxury vehicles with its 'Performance Luxury' philosophy that emphasizes individuality and cutting-edge technology. The brand achieved tremendous success in the North American market upon its launch. 3. Acura's models are designed, developed, and manufactured in North America, resulting in a diverse product line led by models such as the TL, RL, and MDX. 4. The Acura brand officially entered the Chinese market on September 27, 2006.
14
4
Share

How to Deal with Frost on the Inside of a Car Windshield?

There are four solutions to deal with frost on the inside of a car windshield: 1. Use warm air to defrost: Start the car and, once the engine coolant temperature rises, blow warm air onto the windshield until the ice melts. However, this method has certain drawbacks as it is time-consuming, labor-intensive, and consumes more fuel. 2. Physical defrosting: When there is snow and ice on the glass, use a plastic scraper or a glass frost scraper to remove it. A glass frost scraper is more convenient, faster, and does not freeze your hands. 3. Chemical defrosting: Use a spray de-icer to remove frost. This is a high-speed anti-ice spray concentrate specifically designed to thaw frozen car windows and wipers, which does not damage the car's surface and can prevent re-freezing and dirt accumulation. 4. Maintain consistent temperature inside and outside the car: When parking, you can first open the car door and wait for a while until the warmer air inside the car is expelled. Close the door when the temperature inside and outside the car is similar, which can reduce the likelihood of frost forming on the windows.
8
5
Share

Where is the battery located in an Audi A4?

Audi A4's battery is located in the trunk, beneath the spare tire after opening the trunk. Additional information is as follows: Car batteries, also known as storage batteries, are a type of battery that works by converting chemical energy into electrical energy. They are categorized into conventional batteries, dry-charge batteries, and maintenance-free batteries. Typically, what people refer to as car batteries are lead-acid batteries. The normal service life of a car battery ranges from 1 to 8 years, largely depending on the vehicle's condition. When the car is not used for an extended period, it is advisable to disconnect the negative terminal of the battery to prevent battery drain. If the car remains unused for a long time, it's beneficial to take it out for a short drive occasionally, allowing the alternator to recharge the battery. During winter, try to avoid leaving the car parked outside overnight, as this may lead to difficulty starting the engine the next morning. The low outdoor temperatures in winter can shorten the battery's lifespan. During routine maintenance, have a technician measure the battery's internal resistance and voltage to assess its condition.
11
3
Share

What Causes Engine Idle Shaking When Cold?

There are 5 main reasons for engine idle shaking when cold: 1. Dirty air filter: The air filter is designed to protect the engine and reduce wear. Simply replace the air filter. 2. Broken high-voltage wire: A broken high-voltage wire refers to a break in the wire core, which can affect ignition and cause engine shaking. 3. Low idle speed: The engine idle speed is preset in the computer. When the RPM drops below a certain range, the car's computer will automatically adjust it. 4. Abnormal water temperature: The engine operating temperature has a normal range. High water temperature can cause early ignition timing, changes in the air-fuel mixture, thinning of engine oil viscosity, and reduced lubrication performance. 5. Clogged fuel injector: The fuel injector in an EFI car is a key component for fuel injection and has a long service life, reaching hundreds of thousands of kilometers. However, gum deposits in gasoline can clog the injector nozzles, causing inconsistent fuel injection among injectors, leading to uneven cylinder operation and engine shaking.
15
4
Share

Where is the Lynk & Co car produced?

Lynk & Co currently has two factories in China. The first factory is the Volvo Taizhou Luqiao Plant, where the Lynk & Co 01 is produced. The second is the Zhangjiakou Plant, which manufactures the Lynk & Co 02 and 03. Below is some relevant information about Lynk & Co: 1. Lynk & Co is a premium brand of the new era, jointly established by Geely Holding Group, Geely Auto Group, and Volvo Cars. It is based on the CMA (Compact Modular Architecture) mid-size car platform, co-developed by Volvo Cars and Geely Auto, with Volvo Cars taking the lead. 2. The Taizhou Luqiao Plant is one of Volvo's three major vehicle production bases in China, where the Lynk & Co 01 shares the same factory with the Volvo XC40. 3. The Zhangjiakou Plant is a world-class production line heavily invested in by Lynk & Co, featuring automation, informatization, flexibility, and environmental sustainability in a modern factory setting. 4. The workshop is equipped with a real-time IT information system, making it a highly advanced automobile manufacturing facility.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.