Where to Insert USB in Geely Emgrand?

What is the tire size of the Zotye T600?

Its length, width, and height are 4631mm, 1893mm, and 1694mm respectively, with a wheelbase of 2807mm. Below is the relevant introduction about the tires of the Zotye T600: 1. The tire model of the Zotye T600 is 235/60R18. Tire models are commonly represented by a set of numbers, where the first number indicates the tire section width, and the latter indicates the rim diameter in inches. Some tires also contain other letters or symbols with special meanings, such as X for high-pressure tires, C for reinforced tires, and B for bias tires. The Zotye T600 is a mid-size SUV under the Zotye brand. In terms of power, the vehicle is equipped with a 1.5L turbocharged engine, with a maximum power of 119kw and a peak torque of 215nm, paired with a 5-speed manual transmission. 2. The tires used on the T600 are from Qingdao Luhang. For most consumers, Qingdao Luhang tires are not a well-known brand. The CLV2 series used in the sports version is defined by Luhang as a full-condition SUV-specific tire, paired with 18-inch double five-spoke wheels for a sporty and visually appealing effect.

3

0

Share

Why can't the Mercedes-Benz C200 start even though it has power?

The reasons why the Mercedes-Benz C200 cannot start despite having power are: 1. The starter is damaged; 2. There is an issue with the ignition system or fuel supply system; 3. There is a problem with the electrical circuit. If this situation occurs, it is recommended to immediately go to a 4S shop or a professional repair facility to read the fault codes. Only by reading the fault codes can the exact problem be identified. The Mercedes-Benz C has already been domestically produced. The domestic version of the vehicle uses three types of engines: a low-power 1.5-liter turbocharged engine, a high-power 1.5-liter turbocharged engine, and a 2.0-liter turbocharged engine. The low-power 1.5-liter turbocharged engine can deliver maximum power at 5,700 rpm and maximum torque between 1,500 to 4,000 rpm. The high-power 1.5-liter turbocharged engine can deliver maximum power at 6,100 rpm and maximum torque between 3,000 to 4,000 rpm. The 2.0-liter turbocharged engine can deliver maximum power at 6,100 rpm and maximum torque between 1,800 to 4,000 rpm.

4

Share

How to Check After Car Window Tinting?

After car window tinting, the inspection methods are: 1. Check for dirt and debris between the film and the glass on the exterior of the car; 2. The film surface should not have folds, water bubbles, air bubbles, or surface scratches; 3. Observe from inside the car looking outward—there should be no obvious gaps allowing light between the film and the window glass edges, no water-squeezing marks, water ripples, or heat-shrinking marks on the film surface. The functions of car window tinting are: 1. Heat insulation and sun protection, reducing the interior temperature; 2. UV blocking, slowing down the aging of car interiors; 3. Preventing injuries to passengers from accidental glass breakage; 4. Maintaining privacy and safety. Car window tinting is applied to the inside of the car glass, including the front windshield, rear windshield, side windows, and quarter windows.

11

4

Share

Can You Still Drive If the Generator Is Broken?

You can still drive if the generator is broken. A car with a broken generator usually has insufficient battery voltage, making it difficult to start. You will need to jump-start the car, and after starting, you should replace the generator at a repair shop as soon as possible. Below is additional information about generator failure: 1. If the generator is broken, you generally need to jump-start the car. 2. The method for jump-starting a car is relatively simple, but it is important to ensure the connections are correct to avoid short circuits. 3. When connecting the batteries of two cars with jumper cables, the correct method is to connect positive to positive and negative to negative. Car batteries usually do not have very high voltage, so there is no risk of electric shock, and proper jump-starting will not damage the car. 4. If the positive and negative terminals are connected incorrectly, starting the car may cause both batteries to burn out. When starting the powered car, do not disconnect the jumper cables and the car's battery. 5. After ensuring the batteries are correctly connected, you can start the powered car. At this time, turn off all electrical devices in the unpowered car, wait a while, and then start the unpowered car. After starting, let the car idle for a while before disconnecting the jumper cables.

11

3

Share

What type of engine oil does the BJ40 use?

The BJ40 series is equipped with turbocharged engines, so it is recommended to use fully synthetic engine oil with a viscosity of 40. Turbocharged engines have higher requirements for engine oil. More details are as follows: 1. Engine oil is known as the lifeblood of the engine. Inside the engine, it not only lubricates but also cleans, seals, buffers, dissipates heat, and prevents rust. Without engine oil, the engine cannot operate normally. During operation, the oil forms a thin film on the surfaces of various engine components, preventing direct contact and friction between them. 2. When selecting engine oil viscosity, it is essential to choose the appropriate viscosity based on your engine's technical characteristics. The viscosity of the oil should neither be too high nor too low. If the viscosity is too low, the oil cannot form a stable film inside the engine. If the viscosity is too high, it will increase the resistance during engine operation, affecting power output and fuel economy. Generally, a viscosity of 40 is suitable for turbocharged engines. 3. Over time, the performance of engine oil degrades, so it needs to be replaced regularly. It is advisable to change the oil on schedule during regular vehicle use and replace the oil filter with every oil change. When purchasing an oil filter, always opt for genuine products from reputable brands.

8

4

Share

How to Reset the Maintenance Light on Tiggo 7?

To reset the maintenance light on Tiggo 7, follow these steps with the ignition key in the off position: Press and hold the overlapping square button on the right side of the steering wheel. While keeping the button pressed, turn the ignition switch to the ON position. Hold for a moment, and the maintenance light will be cleared. Below are the detailed steps to reset the maintenance light on Tiggo 7: 1. Turn off the ignition switch and shut down the car. Locate the "Menu Switch" button on the steering wheel, which is the overlapping squares button. Press and hold the "Menu Switch" button, then turn the ignition switch to the "ON" position. 2. After the car is powered on, it will begin self-inspection. Keep pressing the "Menu Switch" button during this time. Once the self-inspection is complete (approximately 5 seconds), the maintenance light will reset. Restart the car, and the maintenance light will no longer illuminate. The maintenance light functions to record the mileage of important components, similar to a timer in a sprint race, serving as a reminder for both the car owner and maintenance personnel. Although the maintenance light is not directly related to the car's performance, it is crucial to reset it after maintenance. Otherwise, the owner won't be able to accurately track the usage time of new components during the next replacement.

3

0

Share

Where to Insert USB in Geely Emgrand?

What is the tire size of the Zotye T600?

Why can't the Mercedes-Benz C200 start even though it has power?

How to Check After Car Window Tinting?

Can You Still Drive If the Generator Is Broken?

What type of engine oil does the BJ40 use?

How to Reset the Maintenance Light on Tiggo 7?

What models are available in the Mercedes-Benz C-Class?

How Many Liters of Transmission Fluid Does a Porsche 718 Need?

How many meters can you drive in first gear during the third driving test?

How to Adjust the Height of Civic Seat Belt?