Where to Check Vehicle Registration Date?

1 Answers
McHannah
07/29/25 11:30pm
Vehicle registration date can be found on the or . Below is relevant information: Registration Date: The vehicle registration date refers to the date when the registration application was approved by the vehicle management office. When applying for registration, the vehicle owner shall fill out the application form, present the vehicle for inspection, and submit the following documents and certificates: (1) Identity proof of the vehicle owner. (2) Proof of vehicle origin such as purchase invoice. (3) Vehicle factory qualification certificate or import certificate for imported vehicles. (4) Proof of payment of vehicle purchase tax or tax exemption certificate. (5) Compulsory traffic accident liability insurance certificate. (6) Proof of vehicle and vessel tax payment or tax exemption certificate.
Was this review help?
2
5
Share
More Forum Discussions

What to Do When the Steering Wheel of a Van Feels Heavy?

The heavy steering wheel of a van indicates an issue with the power steering system. The possible causes are as follows: 1. The power steering system contains a large amount of air, leading to abnormal steering. 2. Foreign objects in the steering hydraulic lines cause the steering pump flow control valve to stick. 3. Loose connections in the power steering system result in steering fluid leakage. 4. Excessive wear of the steering gear piston cylinder, poor oil seal sealing, or control valve sticking or damage. 5. The power steering warning light usually indicates heavy steering, steering noise, steering wheel vibration, or poor steering wheel return ability. Steering noise may occur due to the steering system operating under excessive load, causing excessive wear of the rotor and irregular movement of the oil in the pump, leading to noise. It could also be due to internal wear of gears and the rack-and-pinion steering gear assembly.
19
0
Share

What is the tutorial for replacing coolant?

The method for replacing coolant is as follows: Before completely replacing the coolant, conduct a thorough inspection to check for any signs of leakage or cracks in the pipes, with a focus on the five-way water pipe. The five-way pipe is named for its five connections to various parts, and the coolant is distributed to different sections of the car after flowing through it. If there is any leakage of coolant in this section, replace the water pipe or resecure the connections as needed. Drain the old coolant, then flush the fluid channels with clean water. Add clean water to the coolant reservoir, then continuously inject water into the reservoir to allow it to flow through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. Initially, the water flowing out of the reservoir will have a faint pink color. Continue injecting clean water until the outflow is clear. Note: Remember to remove the heater hose and drain the water from the heater core. After draining for about an hour, add the new coolant through the radiator hose to allow it to flow quickly into the radiator. Then, add another bottle of coolant to the reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. As some air is expelled from the cooling system, the fluid level will drop. Add more coolant until it reaches the "MAXT" mark on the reservoir.
7
5
Share

Can Airbags Be Installed?

Airbags can be installed. The following precautions should be taken during installation: 1. Do not use simple tools such as test lights, voltmeters, or ohmmeters. Instead, use a high-impedance multimeter to test the airbag system's circuits and the SRS warning light. 2. Dismantling work must only begin after turning off the ignition switch and disconnecting the negative battery cable for at least 20 seconds. 3. Do not leave airbags unattended. When storing them, place them with the cushioning side facing upward. If stored face down, accidental deployment may occur, leading to serious accidents. Never place any objects on the airbag assembly. If the inflator component falls from a height of more than 90mm, it should not be reused. 4. To prevent damage to the airbag assembly, keep it away from oil, grease, cleaning agents, water, and similar substances. 5. If the vehicle is involved in a minor collision and the airbag system is not triggered, still inspect the steering wheel pad, front passenger airbag assembly, seat belt pretensioners, and airbag sensors.
12
5
Share

Is Bentley Entirely Handcrafted?

Bentley is not entirely handcrafted, as there are no completely handcrafted cars in the world. More details about Bentley are as follows: 1. Bentley is one of the world's premier automobile manufacturers. Walter Owen Bentley, affectionately known as "W.O.", began as an apprentice at the Great Northern Railways in England. During World War I, he was responsible for designing engines for the Camel aircraft and Snipe fighter planes. His passion for speed and performance, coupled with the belief that winning races could boost car sales, led W.O. to establish Bentley Motors in 1919. 2. Bentley Motors Limited is a luxury car manufacturer founded in August 1919, headquartered in Crewe, England. Bentley was acquired by the Volkswagen Group in 1997. Starting in 2002, Bentley replaced Rolls-Royce as the sole designated car brand for the British royal family and served as the official vehicle for Queen Elizabeth II's Golden Jubilee celebrations.
9
0
Share

How is speeding determined?

Speeding is determined through the following methods: 1. Eyewitnesses: including vehicles behind, pedestrians, surveillance cameras, etc. 2. Conduct speed tests based on vehicle damage. Also, note that if the other party did not brake, there may be issues with improper measures taken. If the traffic police issue an appraisal report that does not mention speeding, you can disregard this conclusion and directly file a lawsuit in court. At that time, evidence will need to be provided. So the key is still to have evidence. You can also conduct speed tests with more authoritative institutions. 3. Exceeding the maximum speed limit for that road section is considered speeding. Many road sections have speed limit signs, which are red circular signs with a number inside indicating the maximum speed for that section.
16
4
Share

How to Identify an Odometer Rollback Car?

Methods to identify an odometer rollback car are as follows: 1. Odometer Rollback Device: Locate the vehicle's speed sensor, usually installed near the transmission. The speed sensor typically has three or two wires. Insert the rollback device directly into the cigarette lighter, connect the rollback device and its extension cable, turn on the ignition switch, rotate it slightly, adjust the buttons on the rollback device to modify the speed. 2. Alter the CPU memory data in the instrument circuit: Remove and disassemble the instrument panel. 3. Computerized Odometer Rollback Device: Connect the device data cable directly to the vehicle's OBD port, then select the odometer calibration. Choose the corresponding vehicle model, and after entering the model, proceed to modify the mileage.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.