Where to Check the Standard Tire Pressure for Cars?

2 Answers
StLeah
07/28/25 9:14pm
Standard tire pressure can generally be found in the vehicle's user manual, on the label near the driver's side door (B-pillar), in the drawer next to the driver's seat, or on the fuel tank cap. The tire pressure marking is usually located on the sidewall of the tire. This marking typically indicates the maximum load capacity of a single tire and the maximum safe inflation pressure under normal conditions. For example, if the tire sidewall reads "MAX.PRESS.350kPa," it means the maximum safe inflation pressure for that tire under normal conditions is 350 kPa. Similarly, "MAX.Load 615KG" indicates that the maximum load capacity for a single tire is 615 kg. According to the international standard GBT2978-2008, the recommended tire pressure for standard tires is 2.4-2.5 bar, while reinforced tires should be inflated to 2.8-2.9 bar. The maximum pressure should not exceed 3.5 bar. These values serve as reference points, and adjustments should be made based on factors such as season, driving conditions, vehicle load, and tire condition.
Was this review help?
17
2
Share
Wood
08/12/25 1:54am
I remember being completely clueless about tire pressure when I first started driving, until I discovered it's actually printed on a label along the door frame—usually on the driver's side door jamb or inner door panel. That label shows the manufacturer's recommended standard values, measured in either bar or psi depending on the vehicle model. The owner's manual also includes a detailed chart, and I always advise beginners to check the glove compartment for it. Don’t overlook the fuel filler cap either—sometimes there’s a small sticker there too. Maintaining proper tire pressure is crucial because it affects fuel efficiency, tire wear, and driving safety. I’ve made it a habit to check cold tire pressure monthly using an inexpensive tire gauge—it’s quick and easy. If you’re not keen on manual checks, modern cars with tire pressure monitoring systems will alert you, but I still recommend referring to the factory standards. Remember, values vary by vehicle—SUVs may require higher pressure, while compact cars tend to be lower. In short, developing this inspection habit saves money and gives peace of mind.
Was this review help?
1
2
Share
Expand All
More Forum Discussions

Is it true that tape can open car windows?

Tape cannot open car windows. Here are some additional details: 1. Car anti-theft systems have been upgraded. If tape could easily pull down windows, it would encourage theft. 2. It's very difficult to pull down car windows with tape. The adhesive from the tape would stick to the glass. Most transparent tapes use ordinary organic solvents, which can turn yellow over time, leaving marks on the window and affecting its appearance. 3. If you forget your keys and need to open the window, you can use a wire to reach in and retrieve the keys. 4. If you leave your car keys inside the car, opening the window isn't the only solution. You can also use a spare key or call a professional locksmith to unlock the door.
20
5
Share

What is the weight of the Wrangler?

The Wrangler has a body weight of 1.9 tons. More details about the Wrangler are as follows: 1. The Wrangler's four-wheel-drive technology is the Rock-Trac part-time four-wheel-drive system: Part-time four-wheel drive means the driver manually engages or disengages the transfer case to switch between two-wheel or four-wheel drive modes. The four-wheel-drive system significantly improves the vehicle's stability under harsh conditions, giving the Wrangler exceptional climbing ability. 2. The Wrangler features a rugged and masculine body outline, wide front and rear wheel arches, a seven-slot grille on the front, round headlights, and a dual-top combination design: The Wrangler is equipped with both soft and hard tops, maximizing the fun of open-top driving for the owner while being very easy to operate. The soft top is made of a unique three-layer canvas fiber that reflects road noise, absorbs wind noise, prevents vibration, and enhances the overall thermal insulation of the body.
11
0
Share

How to Reset the CRV Tire Pressure Warning?

To reset the Honda CRV tire pressure warning, first turn on the ignition and locate a cylindrical button on the panel below the steering wheel. Here are the detailed steps for resetting the Honda CRV tire pressure warning: 1. Press and hold the button for more than 3 seconds until the yellow tire pressure warning light flashes and then turns off to reset the warning. Note that the tire pressure warning can only be reset after confirming that the tire pressure is normal. 2. When the tire pressure is too high, it reduces the contact area between the tire and the ground, increasing the pressure the tire bears. This affects the tire's grip, and when the vehicle passes over bumps or uneven surfaces, the tire lacks sufficient space to absorb vibrations, leading to increased impact on the suspension system. 3. Insufficient tire pressure is the leading cause of tire blowouts. Choosing a model equipped with a tire pressure monitoring system is a way to prioritize vehicle tire safety and avoid damage to both the vehicle and its occupants.
8
0
Share

What gear should be in when waiting at a red light?

It is recommended to adopt the following methods according to different situations: 1. For red lights lasting about 10 seconds, it is suggested to stay in D gear and press the brake. Automatic transmission models generally have four gears, namely P, R, N, and D gears in sequence. D gear is the forward gear. Adhering to the principle of not frequently shifting gears, if the red light is very short, about 10 seconds, then there is no need to switch gears again, just stay in D gear and press the brake. 2. For red lights lasting more than 30 seconds, it is recommended to shift to N gear and pull the handbrake. If the red light lasts more than 30 seconds, and some intersections in urban areas may even have red lights lasting up to 99 seconds, then it is generally recommended to shift to N gear, which is the neutral gear, and then pull the handbrake, so that the foot can be released for a slight rest.
7
0
Share

How to Use the Headlights on a BMW X1?

How to use the headlights on a BMW X1: 1. Inside the cabin, you can find the light control lever on the left side of the steering wheel and the left side of the center console; 2. Push the entire light lever upward to turn on the right turn signal, and downward to turn on the left turn signal; 3. Push the light lever forward one position to engage the constant high beam setting; 4. Push the light lever backward one position to engage the single high beam flash setting; 5. The light lever defaults to the low beam position; 6. Rotate the knob to the middle dot position for the parking light setting; 7. Manually adjust the knob to the low beam position to turn on the headlights; 8. The headlight height can be adjusted using the knob below; 9. Turn the knob counterclockwise to control the fog lights—the left symbol is for the front fog lights, and the right symbol is for the rear fog lights.
3
4
Share

What is the function of urea solution for heavy trucks?

The function of urea solution for heavy trucks: It is used to reduce nitrogen oxides in vehicle exhaust, thereby lowering the pollution level of vehicle emissions. The urea solution for vehicles is a colorless, transparent, and clear liquid with a concentration between 31.8%-33.2%. Currently, the urea solution used in vehicles is generally composed of 32.5% high-purity urea and 67.5% deionized water. Below is an introduction to vehicle urea: 1. Vehicle urea solution was first used in Europe, where it is called Adblue. In North America, it is referred to as DEF (Diesel Exhaust Fluid), and in China, it is known as vehicle urea solution or "vehicle denitrification agent." However, it is now commonly referred to as "vehicle urea" in China. 2. Vehicle urea solution is key to reducing pollutant emissions from diesel vehicles. It is a urea-based chemical reactant, made by mixing high-purity urea with deionized water, forming a solution with a concentration of 32.5%. The application of vehicle urea solution in SCR systems is crucial for achieving National IV and higher emission standards for engine exhaust.
17
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.