Where to Change the Wrong License Plate for ETC?

1 Answers
DiAdaline
07/30/25 2:48am
If you need to change the license plate for your ETC, you must bring the license plate change procedures, along with your ID card and vehicle license, to the original bank processing point or any ETC processing point opened by the highway to handle the change. The ETC installation process is as follows: Upon receiving the device, first check whether the ETC card and the electronic tag (OBU) are damaged. Press the anti-tamper button on the back of the OBU, and the red light will briefly turn on. The OLED screen will display "Tag Invalid" or "Please Insert Card," indicating the device is functioning normally. Clean the front windshield to ensure the glass surface is smooth, clean, and dry. Then peel off the protective film on the back of the OBU and stick it to the installation position. Press it firmly with your hand for 2-3 minutes to remove any air bubbles. Insert the ETC card with the front side facing the driver and the back side facing the windshield, ensuring the chip is inserted into the OBU device.
Was this review help?
2
0
Share
More Forum Discussions

At what age is a large vehicle license downgraded?

Large vehicle license downgrade occurs at the age of 60. Large vehicle license: According to Article 59 of the 'Regulations on the Application and Use of Motor Vehicle Driving Licenses', holders of large passenger vehicle, tractor, city bus, medium-sized passenger vehicle, or large truck driving licenses who are 60 years of age or older must downgrade to a small car or small automatic transmission vehicle driving license. Those aged 60 or above are prohibited from driving large passenger vehicles, tractors, city buses, medium-sized passenger vehicles, large trucks, trolleybuses, and trams. Precautions: When starting, the coordination of clutch, throttle, and handbrake must be precise, especially the timing of releasing the handbrake. For uphill starts, hold the clutch engagement point slightly longer and apply slightly more throttle. However, an advantage of large vehicles is that starting in first gear provides more power than small cars, making it easier to start. When driving heavy trucks, it's essential to understand their characteristics: heavy trucks have greater mass and inertia; higher center of gravity and greater centrifugal force. The long body occupies more space. The long wheelbase results in significant inner wheel difference. Air brakes provide faster braking response. The steering wheel is larger and responds slower compared to small cars. There are more gears (six or more) with smaller gear gaps, making the operation more complex and demanding than driving small cars.
18
3
Share

What is the cause of fault code P0597 in Dongfeng Peugeot vehicles?

Dongfeng Peugeot vehicle fault code P0597 reason: Thermostat heater control circuit/open circuit. Below is relevant information about the P0597 fault code: 1. Solution: When the water temperature exceeds the set temperature, the thermostat opens, allowing coolant to circulate to the radiator, effectively improving cooling efficiency. This fault code indicates that the electronic control unit (ECU) has detected that the thermostat heater control circuit voltage exceeds the calibrated normal range. Simply reconnect any loose plugs or replace the heater fuse. 2. Precautions: When clearing fault codes, it is essential to follow the specified clearing method for the corresponding vehicle model. Never directly disconnect the negative battery cable just to clear the fault codes.
9
5
Share

How to Charge Wuling Hongguang Mini at Home?

Wuling Hongguang Mini can be charged at home by using the included charger connected to a 220V power source. Below is an introduction to the Wuling Hongguang Mini: 1. Exterior: Length: 2920mm, Width: 1493mm, Height: 1621mm, Wheelbase: 1940mm, Curb Weight: 665kg. 2. Powertrain: Equipped with a permanent magnet synchronous motor, paired with a single-speed fixed gear ratio transmission. 3. Configuration: The Wuling Hongguang Mini features a MacPherson strut front suspension and a multi-link non-independent rear suspension.
19
2
Share

Is the BMW X2 an imported model?

The BMW X2 is not an imported model. It is a compact SUV produced by BMW Brilliance, with exterior dimensions of 4379mm in length, 1824mm in width, and 1555mm in height, and a wheelbase of 2670mm. The fuel tank capacity is 61 liters. The BMW X2 is equipped with a 1.5T turbocharged engine and a 7-speed dual-clutch transmission, delivering a maximum power of 103 kW at 6500 rpm and a maximum torque of 220 Nm at 4200 rpm.
12
3
Share

What does the Audi fault code P310B mean?

Audi fault code P310B indicates the following: Low-pressure fuel pressure sensor malfunction or communication failure. Below is relevant information about fault code P310B: 1. Solution: Measure the low-pressure fuel pressure with a fuel pressure gauge. First, replace the fuel filter. If the fault persists, replace the fuel pump. 2. Cause of the fault: Low fuel pressure regulation, fuel pressure exceeding specifications. The fuel pressure regulator is clogged or damaged. 3. Reasons for the fault code generation: The meaning of this automotive fault code is that under closed-loop conditions, the air-fuel ratio adjustment exceeds the upper limit. Issues such as air intake system leaks, insufficient fuel pressure, poor cylinder performance, inaccurate air flow meter data, injector damage, or ignition system malfunctions may all trigger this fault code.
10
5
Share

What is the typical firing order for domestic six-cylinder engines?

1-5-3-6-2-4 or 1-4-2-6-3-5. Four-stroke inline six-cylinder engine: The firing interval angle of a four-stroke inline six-cylinder engine is 720 degrees/6=120 degrees. The six crank throws are arranged in three planes, with a firing order of 1-5-3-6-2-4. Firing order for V6 engine: For a V6 engine, it's essential to first clarify the cylinder numbering sequence since V-engine cylinder numbering methods vary. Generally, when sitting in the driver's seat, if the right bank cylinders are numbered 1, 3, 5 from front to rear and the left bank 2, 4, 6, the firing order is typically 1-4-5-2-3-6. If the right bank is numbered 2, 4, 6 and the left bank 1, 3, 5, the firing order is usually 1-6-5-4-3-2. The firing interval angle for four-stroke V6 engines remains 120 degrees, with three crank throws at 120 degrees to each other. The working sequence is R1-L3-R3-L2-R3-L1. Facing the engine's cooling fan, the right bank cylinders are denoted by R (R1, R2, R3 from front to rear) and the left bank by L (L1, L2, L3), forming the working cycle.
9
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.