Where to Buy License Plate Screws for Cars?

1 Answers
VonTravis
07/30/25 3:08am
It is recommended to purchase license plate screws at the vehicle management office. You can also buy them at 4S stores or regular auto repair shops. Below is more information about license plate registration: 1. Required materials for new car registration: ID card, vehicle certificate of conformity, vehicle parameter sheet, second and fourth copies of the car invoice, vehicle purchase tax, car insurance policy, purchase invoice, vehicle certificate of conformity, ID card or organization code certificate and its copy for invoice issuance, compulsory insurance policy, tax payment certificate, and temporary residence permit for non-local residents. 2. Registration process: After preparing the materials, go to the vehicle management office to submit the documents, sign as the owner, have the vehicle inspected and confirmed by traffic police, choose the license plate number yourself, receive the receipt, install and secure the license plate, take photos, and then receive the vehicle license and registration certificate.
Was this review help?
6
1
Share
More Forum Discussions

What are the common faults of FAW Besturn X40?

About the common faults of FAW Besturn X40 are introduced as follows: 1. Circuit or electronic faults: Circuit faults include: blown fuse, open circuit in high-voltage coil, open circuit in low-voltage circuit, detached central ignition wire, leaking distributor rotor, damaged spark plug. Electronic faults mainly refer to the malfunction of the central computer control board. 2. Fuel system faults: Stalling caused by fuel system faults often shows symptoms like weak engine power and the accelerator pedal feeling like stepping on cotton. Possible locations of fuel system faults include: fuel pump failure, blocked fuel line, clogged fuel filter, carburetor failure, damaged injector, etc. 3. Mechanical faults: Common mechanical faults include: timing belt breakage, cylinder leakage with no pressure, etc.
2
0
Share

How to Clean the Throttle Body?

Throttle body cleaning methods: Disassemble and clean the throttle body by removing the entire throttle body assembly, then thoroughly clean it with a specialized cleaning agent before reinstalling. However, since the throttle valve continuously opens and closes during engine operation, causing direct wear with the throttle body, the two worn surfaces can maintain a tight fit before disassembly. If the assembly position is altered after disassembly, it may result in improper sealing and cause malfunctions. For a no-disassembly cleaning method, spray throttle valve cleaner onto a cloth and wipe the throttle body directly. This method does not require disassembling the throttle body; only the intake pipe needs to be removed to expose the throttle body. The throttle body is a controllable valve that regulates air intake into the engine, available in traditional cable-operated and electronic throttle types. After entering the intake pipe, the air mixes with gasoline to form a combustible mixture for combustion and power generation.
1
3
Share

What is the standard tire pressure for the Pajero?

The standard tire pressure for the Pajero is 2.3 to 2.5 bar. The Mitsubishi Pajero is an off-road vehicle under the Japanese automaker Mitsubishi Motors. It features a 5-door, 7-seat SUV body style with exterior dimensions of 4900mm in length, 1875mm in width, and 1900mm in height, and a wheelbase of 2780mm. The Pajero is equipped with a 3.0-liter, 174-horsepower V6 engine (model 6G72), paired with a 5-speed automatic transmission. Its suspension system consists of a double-wishbone independent front suspension and a multi-link independent rear suspension. Additionally, the Pajero comes with a four-wheel anti-lock braking system (ABS) and an electronic brake-force distribution system (EBD).
15
0
Share

Which country produces the Audi A6?

Imported Audi A6 models are manufactured in Munich, Germany, with vehicle identification numbers starting with "WUZ"; domestically produced Audi A6 models are manufactured in Changchun, Jilin, with vehicle identification numbers starting with "LFVBA". The dimensions of the domestically produced Audi A6 are 5012mm in length, 1855mm in width, and 1485mm in height, with a wheelbase of 2945mm, a top speed of 240km/h, and front-wheel drive. The minimum ground clearance of the domestically produced Audi A6 is 142mm, equipped with a 2.0T 170 horsepower L4 engine, paired with a 7-speed CVT automatic transmission.
11
0
Share

Where is the Mercedes-Benz auxiliary battery located?

Most Mercedes-Benz vehicles have the auxiliary battery located on the right side of the trunk. Here are the specific steps to locate the Mercedes-Benz auxiliary battery: 1. The auxiliary battery of Mercedes-Benz vehicles is located on the right side of the trunk. 2. Remove the trunk trim panel. 3. After removing the trim panel, you can see the Mercedes-Benz auxiliary battery. The following are the functions of the Mercedes-Benz auxiliary battery: 1. The auxiliary battery is responsible for powering all the electronic devices in the vehicle. 2. It is responsible for starting the engine. 3. It can indicate the battery's charge level or state of charge. 4. When the power consumption of the vehicle's electrical devices exceeds the generator's supply capacity, the battery works together with the generator to supply power to the vehicle's electrical devices.
10
5
Share

What Causes the Abnormal Noise When Braking in a BMW 3 Series?

BMW 3 Series experiencing abnormal noise when braking can be attributed to the following reasons: 1. Reason one: Excessive wear of brake pads. According to the working principle of brake pads, friction is inevitable during operation, leading to wear. When the wear reaches a certain level, the brake pads will lose their braking function. 2. Reason two: Abnormal noise from the suspension system or pressure bearings. Such noises are usually caused by hardened rubber strips on the components, which produce noise when encountering resistance during braking. If the rubber strips have aged, they should be replaced. If the hardening is merely due to cold weather, no action is needed. 3. Reason three: Wear or deformation of the brake disc. Similar to brake pads, due to frictional wear during use, excessive wear or deformation can lead to abnormal noise when braking.
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.