Where to Add Windshield Washer Fluid in a Camry?

What is the method to clear fault codes?

Clearing fault codes involves the following steps: 1. Clean the throttle body; 2. Check whether the throttle pedal sensor's connector is loose and whether the wiring is aged or broken, then replace or repair as necessary. Fault codes typically indicate issues with the throttle body or throttle pedal position sensor. Precautions for cleaning the throttle body include: 1. Avoid using highly corrosive cleaning agents; 2. Be gentle during cleaning to prevent damage to the coating. The method for cleaning the throttle body is as follows: 1. Remove the intake hose to expose the throttle body; 2. Disconnect the negative terminal of the battery, turn off the ignition switch, straighten the throttle plate, spray a small amount of carburetor cleaner into the throttle body, and then wipe it clean with a polyester cloth or high-density non-woven fabric.

14

5

Share

Is the Orlando an SUV?

The Orlando is not an SUV. The Orlando is a compact sedan under the Chevrolet brand, with body dimensions of 4684mm in length, 1807mm in width, and 1628mm in height, a wheelbase of 2796mm, and a trunk capacity of 479 liters. The Orlando features a MacPherson strut independent front suspension and a multi-link independent rear suspension. It is powered by an Ecotec dual-injection turbocharged engine equipped with a Start-Stop intelligent system, delivering a maximum power of 120kW and a maximum torque of 230Nm, paired with a 6-speed automatic transmission.

3

Share

Will the car drift after four-wheel alignment?

After four-wheel alignment, the car will not drift. Four-wheel alignment is based on the four-wheel parameters of the vehicle, adjusting them to ensure good driving performance and a certain level of reliability. The installation of the steering wheels, steering knuckles, and front axle of a car has a specific relative position, which is called front wheel alignment. Front wheel alignment includes four aspects: caster, kingpin inclination, camber, and toe-in. This applies to the two front steering wheels. Similarly, the rear wheels also have a relative installation position with the rear axle, known as rear wheel alignment. Rear wheel alignment includes camber and individual rear wheel toe-in. Together, front wheel alignment and rear wheel alignment are collectively referred to as four-wheel alignment.

16

2

Share

What is the Principle of Auto Hold?

Auto Hold system works by utilizing the extended functionality of the electronic parking brake (EPB) through the brake management system to control the four-wheel brakes. The Auto Hold system is a technological application that enables automatic parking brake functionality while the vehicle is in operation. This technology allows drivers to avoid prolonged braking when the vehicle is stationary and prevents unnecessary rolling when the automatic electronic parking brake is engaged. The primary function of the Auto Hold feature is to prevent the vehicle from rolling backward, making it particularly useful on inclines and during frequent starts and stops. The Auto Hold system, together with the electronic parking brake, forms an intelligent brake control system that integrates temporary braking during driving with long-term parking braking after stopping, all achieved through electronic control for parking brake functionality.

18

3

Share

What is an OBU machine?

OBU is the card insertion machine for highway ETC systems. Utilizing DSRC technology, OBU establishes a microwave communication link with RSU, enabling vehicle identification and electronic toll deduction without stopping during travel. This achieves unmanned vehicle passage without the need to stop or take cards. The correct installation positions for OBU are: 1. Height not less than 1.2 meters and not exceeding 2.5 meters; 2. Installation angle should be between 30 to 90 degrees; 3. For cars and minivans, the OBU device should be installed on the upper middle part of the front windshield horizontally, while for large trucks and buses, the installation position should be on the lower middle part.

14

3

Share

How to replace the battery in a Zotye T700 key?

Method to replace the battery in a Zotye T700 key: Pry open the remote key along the middle gap, then remove the old battery to replace it with a new one. The Zotye T700 is a mid-to-large-sized SUV under the Zotye brand, with dimensions of 4748mm in length, 1933mm in width, and 1697mm in height. It is equipped with two types of engines: a 1.8-liter turbocharged engine and a 2.0-liter turbocharged engine. The 1.8-liter naturally aspirated engine delivers 177 horsepower and a maximum torque of 245 Nm, with a maximum power speed of 5800 rpm and a maximum torque speed range of 2000 to 4000 rpm. It features multi-point fuel injection technology and uses an aluminum alloy cylinder head with a cast iron cylinder block.

7

2

Share

Where to Add Windshield Washer Fluid in a Camry?

What is the method to clear fault codes?

Is the Orlando an SUV?

Will the car drift after four-wheel alignment?

What is the Principle of Auto Hold?

What is an OBU machine?

How to replace the battery in a Zotye T700 key?

What is the function of a car air conditioning system?

What are the body dimensions of the Volkswagen Touareg?

What are the consequences of not adding antifreeze to the car?

How Long Does the License Plate Registration Process Take?