Where to Add Windshield Washer Fluid in a BMW?

What is the tire size of the Lamando?

The tire size for the base model Lamando is 205/60R16, while the high-end model uses 225/50R17. 1. The international standard tire code represents the section height and aspect ratio in millimeters as a percentage. This is followed by: tire type code, rim diameter (in inches), load index (permissible load capacity code), and permissible speed code. 2. The tire size is printed on the sidewall, with two representation methods. The former indicates high-pressure tires, while the latter denotes low-pressure tires. Additionally, there are many markings: D is used for light vehicles, F for medium-sized vehicles, G for standard vehicles, and H, L, J are for large luxury and high-performance vehicles.

3

5

Share

What are the causes of idling vibration in the Buick Excelle?

The common causes of idling vibration in the Buick Excelle are usually a dirty throttle body or excessive carbon buildup in the fuel injectors. Additionally, it is advisable to check the condition of the spark plugs, high-voltage wires, and ignition coils, as poor performance in the ignition system or faulty spark plug firing can also lead to such symptoms. Below are detailed explanations of the major causes of severe idling vibration in the Buick Excelle: 1. A dirty or damaged throttle body affecting idle vibration. The throttle body can be cleaned first, but if the issue persists, the throttle body assembly may need replacement. 2. Faulty spark plugs causing misfire and idle vibration. It is recommended to inspect the spark plugs and ignition module for any malfunctions. 3. Aging or cracked rubber components inside the engine and transmission mounts. These components are unable to absorb the engine's operational vibrations, resulting in idle vibration issues.

13

1

Share

What are the steps to replace the remote control battery for Peugeot 408?

The steps to replace the remote control battery for Peugeot 408 are: 1. Remove the mechanical key and locate the hole for removing the mechanical cover plate. 2. Insert the mechanical key into the hole and gently pry open the key to open the key cover plate. 3. Remove the old battery, install the new battery, cover the car key cover plate, and finally install the mechanical key. More details are as follows: 1. The battery model for Peugeot 408 is CR2032. When the battery needs to be replaced, a prompt message will appear on the combination instrument display. When installing the new battery, pay attention to the positive and negative positions, install the remote control cover, and reinitialize the remote control. 2. If the car key is lost, please bring your ID and vehicle registration documents to an authorized Peugeot service provider to inquire about the key code and remote control code for a new key replacement. 3. During daily use of the key, do not place the key near high-power appliances such as TVs, microwaves, washing machines, or computers, as these appliances can reduce the battery life of the remote control. 4. Do not expose the key to environments below 0°C or above 50°C, as this will significantly reduce the battery life.

17

3

Share

What is the equivalent displacement of 280tsi?

280tsi is equivalent to a displacement of 1.4 liters. In tsi, 't' stands for twin-charging, 's' for stratified, and 'i' for injection. TSI is more advanced than FSI, representing an engine with high power, low speed, and high torque. TSI technology is the comprehensive application of twin-charging and stratified direct injection technologies, which involves relatively high technical requirements. The TSI technology adopted in domestic mid-to-low-end mass-produced vehicles includes turbocharging and fuel stratified injection. TSI direct fuel injection technology achieves a perfect combination of engine power and fuel economy under the same displacement. It is one of the more mature and advanced direct fuel injection technologies in today's automotive industry engine technology, leading the development trend of gasoline engines.

8

3

Share

How to Use the Highlander Snow Mode?

The usage of Highlander Snow Mode: Locate the SNOW mode button on the vehicle, press this button, and you will notice a significant decrease in power output. However, this is just an issue of power transition. As the engine speed increases, the power will gradually recover. You can observe from the dashboard that the power distribution becomes more intelligent, along with real-time monitoring of the external temperature. More details are as follows: 1. After activating Snow Mode, the vehicle reduces engine output power through the electronic throttle control system when driving on slippery roads, minimizing the risk of wheel spin on snow-covered or slippery surfaces. The key purpose of Snow Mode is to prevent vehicle skidding, ensuring smoother and gentler torque output. 2. After engaging Snow Mode, the car automatically adjusts its power and speed. However, it's important to note that Snow Mode doesn't guarantee complete accident prevention. If the vehicle speed exceeds certain limits, the car may lose control. 3. Snow Mode also has requirements for tires. Snow tires use special compounds to increase friction with icy and snowy surfaces. Their advantages include improved traction and safety on snowy roads. The tread material of snow tires is softer, and the specially formulated silica-mixed rubber compound allows closer contact with smooth ice surfaces, generating greater friction than all-season tires. This significantly enhances vehicle handling and safety on slippery ice. 4. When temperatures drop below 10°C, snow tire surfaces become softer, providing better grip. Conventional tires behave oppositely, becoming harder as temperatures decrease.

18

4

Share

What does the start-stop function mean?

The start-stop function refers to the automatic engine start-stop system. When the vehicle comes to a complete stop for a certain period, the engine can be automatically shut off. When you need to move forward, simply pressing the accelerator pedal will restart the engine. The primary purpose of equipping an automatic start-stop system is to save fuel and reduce exhaust emissions. During traffic jams or while waiting at a red light, the engine can automatically shut off and restart when moving to minimize unnecessary fuel consumption and lower emissions. This function mainly aims to reduce the engine's idle running time as much as possible. Additionally, after the engine shuts off, the vehicle's electrical system can replace the belt pulley to provide power for the engine cooling fan and the car's air conditioning system.

3

2

Share

Where to Add Windshield Washer Fluid in a BMW?

What is the tire size of the Lamando?

What are the causes of idling vibration in the Buick Excelle?

What are the steps to replace the remote control battery for Peugeot 408?

What is the equivalent displacement of 280tsi?

How to Use the Highlander Snow Mode?

What does the start-stop function mean?

How to set up one-touch window lift for Jetta?

What is the battery model for the Envision car key?

Where is the ESP switch on the Skoda Kamiq?

Which country is the Cayenne brand from?