Where to Add Windshield Washer Fluid for the New Sylphy?

1 Answers
VivianDella
07/30/25 9:27am
New Sylphy windshield washer fluid filling location: Open the Sylphy's engine hood, locate the windshield washer fluid reservoir. The cap of the spray bottle has an indicator light-like symbol. Simply open the cap to add windshield washer fluid. There is a dipstick inside the reservoir - add fluid while checking the level, stop when it reaches the marked line to avoid overflow. The new Sylphy is a compact car under Dongfeng Nissan, with dimensions of 4641mm in length, 1815mm in width, and 1450mm in height, and a wheelbase of 2712mm. In terms of power, the new Sylphy is equipped with a naturally aspirated engine delivering maximum horsepower of 135PS, maximum torque of 159Nm, and maximum power of 99kW.
Was this review help?
7
2
Share
More Forum Discussions

Which Fuse is the ABS Fuse for the Ford Escort?

The fuse box for the Ford Escort is located under the cover panel to the lower left of the driver's seat. Open the cover to see it. How ABS Works: During braking, ABS quickly determines the wheel lock-up state based on the speed signals from each wheel speed sensor. It closes the normally open input solenoid valve for the wheel that begins to lock up, keeping the braking force constant. If the wheel continues to lock up, the normally closed output solenoid valve opens, allowing the brake pressure on that wheel to rapidly decrease due to the direct connection to the brake fluid reservoir, preventing the wheel from completely locking up due to excessive braking force. This ensures the braking state remains at the optimal point (with a slip ratio S of 20%), achieving the best braking effect and the highest driving safety. Classification of ABS: ABS is mainly classified by channels. In ABS, the brake pipelines that can independently adjust brake pressure are called control channels. ABS control channels are divided into four-channel, three-channel, two-channel, and one-channel types. One-channel ABS: Also known as single-channel ABS, it has one brake pressure regulator in the rear wheel brake assembly and one wheel speed sensor installed on the rear axle differential (some models may have one on each rear wheel). Two-channel ABS: This type of ABS struggles to balance directional stability, steering control, and braking efficiency, and is rarely used today. Three-channel ABS: This system independently controls the two front wheels, while the two rear wheels are controlled together based on the low-select principle (i.e., both wheels are controlled by one channel to ensure the wheel with less traction does not lock up). This is also known as hybrid control. Four-channel ABS: Equipped with four wheel speed sensors, this system has a brake pressure regulator in the pipeline to each wheel brake cylinder, enabling independent control and forming a four-channel control configuration.
13
5
Share

How Often Should the Battery in the Lamando Be Replaced?

The normal service life of the Lamando's battery varies between 1 to 8 years, largely depending on the vehicle's usage conditions. Under normal circumstances, it can last for more than 3 years. If you notice that the battery is not holding a charge, the starter is weak, or the headlights are significantly dimmer, you should remove the battery and charge it for 12-24 hours with a charger. If these issues persist, it may be time to consider replacing the battery. Below are some relevant details about the Lamando: 1. Introduction One: The Lamando is equipped with two types of engines—a low-power version of the 1.4-liter turbocharged engine and a high-power version of the 1.4-liter turbocharged engine. The low-power 1.4-liter turbocharged engine has a maximum power of 96 kW and a maximum torque of 225 Nm, with the maximum power achieved at 5,000 rpm and the maximum torque available between 1,400 and 3,500 rpm. This engine features direct fuel injection technology and uses an aluminum alloy cylinder head and block. It is paired with either a 5-speed manual transmission or a 7-speed dual-clutch transmission. 2. Introduction Two: The high-power version of the 1.4-liter turbocharged engine delivers 150 horsepower and a maximum torque of 250 Nm. This engine reaches its peak power at 5,000 rpm and its maximum torque between 1,750 and 3,000 rpm. Like the low-power version, it incorporates direct fuel injection technology and an aluminum alloy cylinder head and block. It is exclusively paired with a 7-speed dual-clutch transmission. 3. Introduction Three: The front suspension of this car uses a MacPherson independent suspension, while the rear suspension employs a multi-link independent suspension. The Lamando offers excellent handling and strong performance, with the dual-clutch transmission providing rapid gear shifts.
11
3
Share

How to Deal with Unstable Steering in Subject Three?

The reasons and solutions for unstable steering in Subject Three are as follows: 1. Lack of vehicle sense. When trainees notice the car body tilting, the vehicle has already deviated significantly. Adjusting the steering at this point will cause obvious shaking. Solution: Sit upright in the driver's seat and look as far ahead as possible. This helps in sensing whether the car's path is parallel to the road. The farther you look, the sooner you can detect any tilting. 2. Overcorrection. In reality, due to factors like road conditions, the car cannot always go straight. When the car body tilts slightly, minor steering adjustments are needed. However, trainees often turn the steering wheel too quickly and drastically. Solution: Make gentle and slow adjustments to the steering, with minimal angles, allowing the car to correct its direction smoothly. 3. Overcompensation. Some trainees turn the steering wheel too much. Solution: The actual steering adjustment should be about the width of two or three fingers. Use the method of small, frequent adjustments to continuously correct the direction.
8
2
Share

What to Do If Resin Drips on the Car?

Here are the solutions for removing resin from a car: 1. Use a specialized car wash liquid designed for removing asphalt to clean the resin off the car. It has a mild and neutral property, capable of quickly and effectively removing sticky substances like tar, asphalt, and resin from the paint surface. 2. If the resin on the car body is not severe, you can use hot water with a small amount of laundry detergent and scrub the resin off with a brush. 3. You can use volatile liquids like gasoline by soaking a cloth and then wiping the affected area. 4. After removing the resin with volatile liquids like gasoline, rinse the car body with clean water and apply wax for maintenance. 5. You can also use a cleaning agent to treat the resin, followed by washing the car and applying wax to the body. Additional Information: Resin generally refers to organic polymers that soften or melt within a certain temperature range, tend to flow under external force when softened, and are solid, semi-solid, or sometimes liquid at room temperature. Broadly defined, any high-molecular compound that can be used as a raw material for plastic product processing is called resin.
6
0
Share

What Causes Mercedes-Benz Steering Gear Failure?

Mercedes-Benz steering gear failure is typically caused by excessive air in the power steering system, leading to abnormal vehicle steering; foreign objects in the steering hydraulic lines causing the steering pump flow control valve to stick; or loose connections in the power steering system resulting in steering fluid leakage. Abnormal noise during steering: Solution: The cause of abnormal noise during steering is usually due to damage to the kingpin and bushing or failure of the column thrust bearing. In such cases, you can turn the steering wheel left and right to identify the source of the noise and proceed with disassembly and inspection. Steering gear oil leakage: Solution: Steering gear oil leakage usually occurs at three locations: the upper cover of the steering gear, the connection between the steering shaft and the pitman arm, and the side end cover. This is often due to prolonged use of the vehicle causing sealing issues. Since these areas are equipped with sealing rings, replacing the oil seals and sealing rings can resolve the issue. Difficulty in steering wheel return: Solution: Most vehicles have an automatic steering return function. If you need to apply the same force to return the steering wheel as you do when turning, it indicates a malfunction in the return function. This issue is usually found in the mechanical parts of the steering system, such as lack of lubrication causing damage to the kingpin and bushing, lack of lubrication in the universal joint connecting the steering wheel and steering gear, or rust in the tie rod end due to insufficient lubrication. In such cases, visit a professional repair shop for maintenance.
20
3
Share

How to Repair Hail Dents on a Car?

The best method to repair hail dents on a car is through paintless dent repair (PDR). PDR has the following characteristics: it does not require traditional 'bodywork, filling, or repainting,' thus preserving the original car paint; the repair time is short, and the cost is very low. The repair effect is excellent, fully protecting the original car. Hail damage is covered under the vehicle damage insurance provided by insurance companies. If you find your vehicle damaged by hail, you can call the hotline to report the incident and file a claim with the insurance company. Steps to file a claim for hail damage to your car: 1. Report the incident to the insurance company. If you have all the necessary documents, you can report the incident to the insurance company within 24 hours. When reporting, provide detailed information such as the vehicle's parking location, the person who parked it, and the weather conditions. 2. After reporting, undergo inspection and damage assessment. After reporting, the insurance company will arrange for a staff member to contact you and conduct an inspection nearby. During the inspection, the staff will take photos of the vehicle's damage. 3. Documents required for the inspection. During the inspection process, you need to provide the staff with the owner's ID card, the vehicle registration certificate, the original and copy of the vehicle driving license, and the owner's bank card. Ensure all these documents are valid.
13
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.