Where to Add Water in a Car?

How to Reset the Tire Pressure on a Geely Emgrand?

Geely Emgrand's tire pressure reset button is located on the instrument panel display. Adjust the tire pressure to the normal value, then press and hold the tire pressure reset button for 3 seconds to perform the reset. The tire pressure light indicates that the pressure of a certain tire is not within the standard range, and the tire pressure needs to be checked. Taking the new Emgrand GS 1.4T manual Yalife as an example: 1. Dimensions: It is a compact SUV with a length, width, and height of 4440mm, 1833mm, and 1573mm respectively, and a wheelbase of 2700mm. 2. Powertrain: It is equipped with a 1.4T turbocharged engine, paired with a 6-speed manual transmission.

9

5

Share

What to Do When the Reverse Light Doesn't Work?

Here are the inspection methods for when the reverse light doesn't work: 1. Check if the bulb is damaged; remove the tail light and take out the bulb to see if it's functioning properly. 2. Check if the fuse is blown; the reverse light fuse in most cars is located inside the instrument panel. Follow the fuse box diagram to locate the reverse light fuse, and pull it out to check if it's melted. 3. Inspect the reverse light power wire. 4. Check if the reverse light switch is in good condition; unplug the reverse light switch connector and bridge the switch with a wire. If the reverse light turns on, it indicates the switch is faulty. If it doesn't light up, the switch is fine. 5. Check the ground wire.

8

4

Share

How Many Kilometers to Change Synthetic Engine Oil?

Full synthetic engine oil should be replaced every 12 months. Below is relevant information about full synthetic engine oil: 1. Introduction: (1) To achieve better lubrication effects, humans have chemically synthesized various engine oils based on base oils, which are known as chemically synthesized engine oils. (2) Synthetic engine oil manufacturers produce different types of engine oils according to user requirements, and the composition of synthetic engine oils can be adjusted based on their intended use. 2. Definition: The official explanation of synthesis is: achieving the desired molecular form through chemical reactions under controlled conditions, a process called synthesis. The largest component of engine oil is the base oil, which can be classified into five categories based on specification grades. Among these five categories, Group I, II, and III base oils are referred to as mineral oils, while only Group IV and V base oils can be called synthetic oils. Group V base oils are polyol esters (POE), and Group IV base oils are polyalphaolefins (PAO). Therefore, the simplest understanding is that engine oils blended with Group IV and V base oils, along with mineral oils, can be referred to as full synthetic engine oils.

18

0

Share

Why was the Pirelli New P1 discontinued?

Pirelli New P1 tires have not been discontinued; they have simply shifted to online sales. Features of Pirelli tires: 1. Strong durability: Pirelli tires are highly durable with a long service life, offering excellent grip and stability. Even in harsh environments, they maintain robust stability. 2. Responsive handling: Pirelli tires exhibit highly responsive performance on obstacle courses on asphalt roads, with predictable behavior that allows them to fully achieve the desired effects as commanded by the driver. Even in cases of driver error leading to skidding, the tires can quickly provide feedback, stabilize, and regain grip. 3. Outstanding braking performance: Pirelli also boasts excellent braking performance. The tire tread pattern utilizes interlocking fine groove technology, improving performance on both dry and wet surfaces, reducing braking distance under extreme conditions to ensure driving safety.

14

5

Share

What does EBP on a car mean?

EBP on a car stands for Electrical-Park-Brake, which refers to the electronic parking brake system. Here is an introduction about EBP: 1. Introduction to EBP: The electronic parking brake system replaces the traditional mechanical lever and tire cables, providing better assistance to drivers. It substitutes the traditional pull-handle handbrake with an electronic handbrake button, which is safer than the traditional pull-handle handbrake. The braking effect is not affected by the driver's force, transforming the traditional pull-handle handbrake into an easily accessible button. 2. Function of EBP: EBP is mainly applied in tractors and trucks. The EBP intelligent energy-saving system is equivalent to having three gear selection keys for the engine. It allows free selection based on different road conditions and load capacities, keeping the engine operating within the optimal fuel economy range, thereby saving fuel.

14

5

Share

How does the ABS sensor in a car work?

ABS system, also known as the Anti-lock Braking System, works as follows: During braking, the ABS closes the normally open input solenoid valve on the wheel that begins to lock based on speed signals from each wheel speed sensor, keeping the braking force constant. If the wheel continues to lock, the normally closed output solenoid valve is opened. This ensures the braking state remains at the optimal point, achieving the best braking effect and maximum driving safety. ABS, short for Anti-lock Braking System, functions by automatically controlling the braking force during vehicle braking to prevent wheel lock-up. It maintains the wheels in a state of rolling and sliding (with a slip ratio of around 20%), ensuring maximum traction between the wheels and the road. The ABS system primarily consists of four components: wheel speed sensors, the electronic control unit (ECU), the hydraulic unit, and the ABS warning light. The wheel speed sensors detect the motion state of the wheels and generate sinusoidal electronic pulse signals. These signals are then processed by a modulator, converted into digital signals, and transmitted to the electronic control unit. The central electronic control unit (ECU) receives input signals from the wheel speed sensors and uses them to calculate the wheel speed, vehicle speed, and slip ratio. Based on the slip ratio, it determines the wheel's condition and issues control commands to the hydraulic unit. The hydraulic unit adjusts the pressure in the brake lines according to the control commands, with the adjustment process including pressure maintenance, pressure increase, and pressure reduction. The ABS warning light alerts the driver to any system malfunctions. If the ABS warning light illuminates, it is advisable not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.

1

2

Share

Where to Add Water in a Car?

How to Reset the Tire Pressure on a Geely Emgrand?

What to Do When the Reverse Light Doesn't Work?

How Many Kilometers to Change Synthetic Engine Oil?

Why was the Pirelli New P1 discontinued?

What does EBP on a car mean?

How does the ABS sensor in a car work?

Why Do People Go to Tianjin to Buy Cars?

How Long Should You Drive After Jump-Starting a Car?

What to Do When the Motorcycle Won't Start and Makes a Clicking Sound?

Why can the remote key unlock but not lock the car door?