Where is Zhenba Tire produced?

What is the fuel consumption of the 10th generation Honda Accord?

Honda Accord 10th generation fuel consumption is 6. The following is a brief introduction about the fuel consumption of the 10th generation Honda Accord: 1. Fuel economy: Japanese cars are famous for their fuel efficiency, and the 10th generation Accord is no exception. Based on Honda's unique VTEC technology, it adopts direct injection, Atkinson cycle, VTC variable valve timing technology, and introduces an EGR exhaust gas recirculation system, improving fuel economy by 13% and maximum torque by 8%. 2. Fuel consumption: Fuel consumption also depends on individual driving habits, so there is no fixed standard. The 3.0L model is equipped with paddle shifters, allowing gear changes by pulling the left and right paddle shifters, providing a professional racing-like fast control experience.

19

5

Share

What Causes White Smoke from a Car?

Here are the reasons why a car emits white smoke: 1. Incomplete combustion: The engine temperature is too low, causing some fuel to not burn completely, resulting in white smoke being expelled along with the exhaust. 2. Water in the fuel system: If there is water in the fuel system, white smoke may appear when starting the car. Below are related explanations: 1. Car starting: It is normal for white smoke to come out of the exhaust pipe after starting the car because gasoline contains a certain amount of water. When the engine is cold, the temperature is too low, and the fuel entering the cylinders does not burn completely, leading to the formation of mist or water vapor, which appears as white smoke. In this case, once the engine temperature rises, the white smoke will disappear naturally. 2. Things to note: If white smoke comes out of the exhaust pipe due to damaged piston rings, the engine may burn oil. During operation, the engine produces a large amount of exhaust gas containing a lot of water vapor, which results in significant white smoke.

17

2

Share

What brand of engine oil is best for the Atenza?

The original factory oil for the Atenza is Mazda's specialized fully synthetic 5W-40 engine oil. If you wish to change the oil during later maintenance, you can choose brands such as Mobil, Castrol, Shell, or Total. Any fully synthetic 0W-20 oil is suitable. Among these, Shell's Urban Light 0W-20 offers good value for money and excellent noise reduction. For the 2020 Atenza, using 0W-20 oil may result in louder engine noise, so 5W-30 is recommended. For the Atenza 2.5L engine, Castrol's Edge 0W-20 is recommended, while for the 2021 Atenza 2.5L Blue Sky Sport Edition, Mobil, Castrol, or Great Wall 0W-20 viscosity oils are suggested. Engine oil viscosity changes with temperature, so it's crucial to pay attention to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity—5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, ensuring smoother cold starts for the car. The second number represents the oil's kinematic viscosity at 100°C. A higher number means the oil can maintain its viscosity better at high temperatures, which can also be understood as providing better lubrication under high-temperature conditions. The method for changing the engine oil in an Atenza is as follows: Wait for the engine temperature to cool down, allowing the oil to flow back into the oil pan; Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until it stops dripping. Start the engine for about 30 seconds to allow the oil in the main oil passages to drain out; Use a specialized wrench to remove the oil filter; Apply some oil to the seal of the new oil filter and tighten it clockwise by hand; Add the new engine oil through the oil filler cap on the engine valve cover, typically filling about three-quarters of the bottle; Start the engine and let it run for 5 minutes, checking for any leaks around the oil drain plug and oil filter. If leaks are found, repairs should be made; After stopping the engine, pull out the dipstick to check that the oil level is within the standard range.

17

2

Share

What is the difference between China 6 and China 5?

China 6 adopts the fuel-neutral principle, meaning that regardless of the type of fuel used, the emission limits are the same. In contrast, during the previous "China 5" phase, diesel and gasoline vehicles had different emission standards. Compared to China 5, the China 6 standard reduces nitrogen oxides by 77% and particulate matter by 67%. Other relevant information: China 5 standard: The China 5 standard refers to the National Fifth Stage Motor Vehicle Pollutant Emission Standard, also known as "China 5 Standard." The emission control level of China 5 is equivalent to the European Union's fifth-stage emission standard currently in effect. The EU has been implementing this standard since 2009, which imposes stricter limits on nitrogen oxides, hydrocarbons, carbon monoxide, and particulate matter from motor vehicles. From China 1 to China 4, each upgrade in the standard reduces single-vehicle pollution by 30% to 50%.

7

3

Share

How to Solve Severe Inner Tire Wear on Rear Wheels?

Here are the solutions for inner tire wear on rear wheels: 1. Adjust tire pressure: Maintain proper tire pressure at all times. 2. Balance inspection: Regularly perform wheel dynamic balance tests. If imbalance is detected, install balancing weights. 3. Pay attention to tire maintenance and rotation: After driving 5,000 kilometers, it's best to rotate the tires, preferably using the diagonal exchange method to ensure even wear and prolong tire life. Notes: Rear tire uneven wear mostly occurs in vehicles with independent suspension systems. The rear wheel alignment data is adjustable, so when abnormal tire wear occurs, it's essential to visit a professional repair shop for a four-wheel alignment. Otherwise, prolonged neglect may lead to potential tire blowouts, endangering lives.

19

1

Share

How to Turn Off the Rear Wiper on an Old Ford Focus?

The rear wiper switch is located on the knob on the side of the wiper control lever. Press it to the O position to turn off the rear wiper. Here is some relevant information: 1. Wiper Function: The wiper is an important accessory installed on the windshield. Its function is to clear rain, snow, and dust from the windshield that obstruct the view. Therefore, it plays a crucial role in driving safety. If the wiper blade does not clean effectively, remove it, soak it in water, lightly sand it with fine sandpaper, then clean and reinstall it. 2. Precautions: When using the wiper to remove dust from the windshield on sunny days, always spray windshield washer fluid and avoid dry wiping. For other stubborn or hard contaminants on the glass, clean them manually. These substances can easily damage the wiper blade, causing it to clean poorly. In severe cases, the wiper motor may also be affected.

13

1

Share

Where is Zhenba Tire produced?

What is the fuel consumption of the 10th generation Honda Accord?

What Causes White Smoke from a Car?

What brand of engine oil is best for the Atenza?

What is the difference between China 6 and China 5?

How to Solve Severe Inner Tire Wear on Rear Wheels?

How to Turn Off the Rear Wiper on an Old Ford Focus?

Is Borgward a Joint Venture or Domestic Brand?

Is Car Seat Modification Illegal?

Can the repair of the windshield be noticed?

What are the requirements for obtaining an A1 driver's license?