Where is the wiper switch on a Mercedes-Benz?

1 Answers
LeKatherine
07/29/25 12:52pm
Mercedes-Benz wiper switches are generally located on the left side of the steering wheel, combined with the light control on a single lever. The leftmost silver button controls the windshield washer fluid spray—pressing it inward from the outside activates the spray. Slightly to the right is the wiper function control, which can be rotated to switch between five modes: wiper off, low-frequency intermittent wipe, high-frequency intermittent wipe, continuous low-speed wipe, and continuous high-speed wipe. Always check if the wiper blades move in sync; if not, adjust them promptly. If some water remains on the windshield after several wipes, it indicates the rubber blades have aged. Avoid dry wiping, as it can damage the wipers and, if debris is present, may cause significant harm to the windshield.
Was this review help?
6
3
Share
More Forum Discussions

What should I do if the Citroen C-Quatre engine is leaking oil?

If the Citroen C-Quatre engine is leaking oil, the first step is to locate the leakage point. You can replace the sealing ring and then observe the situation. If the oil leakage is still severe, it is recommended to promptly visit a 4S store for maintenance and inspection. Most engine oil leaks are caused by aging or damaged seals. Seals can harden, lose elasticity, and in severe cases, may even break, leading to oil leakage. Here are some relevant details: 1. Minor oil leaks in the Citroen C-Quatre engine mostly occur in quasi-new vehicles with less than 100,000 kilometers on the odometer. These leaks can be difficult to detect without close observation, primarily manifesting as a dirty engine with very small amounts of oil seeping out and mixing with dust to form sludge that adheres to the engine surface. The sludge is often found near the oil pan, oil filler port, and exhaust valve. 2. Obvious oil leakage from the engine may significantly increase oil consumption. The consequence of oil loss is severe engine wear. In such cases, it is not difficult to quickly locate the leakage point. The oil leakage phenomenon is mostly related to aging seals and sealing rings, such as the common front and rear crankshaft oil seals, oil pan sealing rings, and valve cover sealing rings.
9
0
Share

What is the most suitable position to install the blind spot mirror?

The blind spot mirror is recommended to be installed on the inner side of the side mirror, as installing it on the outer side may obstruct the view. The following are the functions of the blind spot mirror: 1. Observe the vehicle body: It allows the driver to better observe the side of the vehicle body and the rear wheels while sitting in the car. If there is a vehicle approaching in the blind spot, it can be detected in time to reduce potential accidents. 2. Observe the reversing position: For novice drivers, having a blind spot mirror makes reversing easier. During parallel parking, it helps to see the relative position of the right wheel. It effectively helps novice drivers develop a sense of the vehicle, especially when parking or reversing, allowing them to better understand the road conditions. 3. Observe road conditions: For drivers who frequently drive on mountain roads, rugged roads, or narrow sections, the blind spot mirror is also very necessary. After installing the blind spot mirror, the driver can better observe the road conditions to adjust the distance between the right side of the vehicle and the road, especially when two vehicles pass simultaneously. The small blind spot mirror on the side mirror plays a more significant role. 4. Good practicality: It is inexpensive and relatively easy to install. The installation position can be determined based on different vehicles and driving habits, offering good practicality.
18
5
Share

What are the differences between BYD Tang and BYD Song?

Here are the differences between BYD Tang and BYD Song: 1. Vehicle type: BYD Tang is a mid-size SUV; BYD Song is an MPV. 2. Space and appearance: The space and appearance of BYD Tang are more stylish and spacious compared to BYD Song. 3. Price: The price of BYD Tang is relatively higher than that of BYD Song. 4. Engine: BYD Tang is equipped with a 2.0T 205 horsepower engine; BYD Song uses a 1.5T engine. Here is some extended information about BYD models: 1. BYD e1, BYD e2, BYD e3, BYD S2. 2. Qin, Han, Tang, Song, Yuan.
16
3
Share

What is the emission standard of BYD S6?

BYD S6 complies with the China 5 emission standard. Here is some extended information about BYD S6: 1. The BYD S6 is a 5-door, 5-seat SUV with body dimensions of 4810mm in length, 1855mm in width, 1725mm in height, and a wheelbase of 2720mm. 2. The BYD S6 is equipped with a 1.5L turbocharged engine, delivering a maximum power of 113 kW at 5200 rpm, and a maximum torque of 240 Nm between 1750 to 3500 rpm. 3. It features MacPherson independent front suspension and multi-link independent rear suspension.
2
0
Share

How often should the coolant be replaced in a Golf 7?

The coolant in a Golf 7 generally needs to be replaced every 2 years or 40,000 kilometers. This is just a reference interval. For commercial vehicles with higher mileage, the replacement interval should be shorter. Since driving conditions vary for each vehicle, the actual replacement should be based on usage. Monitor the coolant level and top it up promptly if it's low. If suspended particles, sediment, or discoloration are observed in the coolant, replace it immediately and flush the system. Coolant replacement procedure: Before a complete coolant replacement, conduct a thorough inspection to check for leaks or cracks in all hoses, with special attention to the five-way hose. Named for its five connecting interfaces to different components, the five-way hose distributes coolant to various parts of the vehicle. If coolant leakage is detected in this area, replace the hose or reseal the connections as needed. Drain the old coolant, then flush the system with clean water. Add water to the coolant reservoir and continuously circulate it through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. Initially, the discharged water may appear slightly pinkish. Continue flushing until clear water emerges. Remember to disconnect the heater hose to completely drain the heater core. Approximately one hour after draining, add new coolant through the radiator hose for rapid filling. Then pour another container of coolant into the reservoir until nearly full. Run the engine for about 10 minutes; as air is purged from the system, the coolant level will drop. Top up the coolant to the "MAX" mark on the reservoir.
16
1
Share

How to reset the tire pressure warning light on the Lamando?

The tire pressure warning light on the Lamando will automatically turn off once the tire pressure of the alerted wheel is restored to the normal value. Turn on the ignition, locate the reset switch above the brake pedal, press it, and the warning light will start flashing. After 5 seconds, the issue will be resolved. Here is more information about tire pressure: 1. To reset the tire pressure on the Volkswagen Lamando, start the car, press and hold the SET button until the tire pressure light on the dashboard turns off, usually taking about 10 seconds. The tire pressure reset function is located in the instrument cluster's onboard computer and can be accessed via the multifunction steering wheel buttons. 2. Tire pressure, strictly speaking, refers to the air pressure inside the tire. Nowadays, many tires are not filled with air. For these tires, the tire pressure requirements are more stringent. Tires filled with air are affected by seasonal changes. Moreover, tire pressure is closely related to vehicle performance, such as comfort and load capacity, and also affects tire lifespan. Air pressure is the lifeblood of a tire; both too high and too low will shorten the tire's service life. Low pressure increases tire deformation, leading to cracks on the sidewalls and excessive flexing, which causes overheating, rubber aging, fatigue in the cord layers, and cord breakage. It also increases the tire's contact area, accelerating wear on the tire shoulders. High pressure overextends the tire cords, reducing the tire's elasticity and increasing the load on the car during driving. Impacts can cause internal cracks and blowouts, while high pressure also accelerates tread wear and reduces puncture resistance.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.