···
Log in / Register

Where is the windshield wiper switch for Tesla Model 3?

4 Answers
LeOlivia
07/23/25 1:05pm
Tesla Model 3's windshield wiper switch is located on the stalk. The middle part adjusts the wiper speed, while the outermost position is for washer fluid spray. To activate the spray, pull the stalk toward the driver. Frequent users should monitor the washer fluid level and refill promptly when low to prevent dry wiping. Additional details are as follows: 1. Windshield wipers, also known as wiper blades or windscreen wipers, are devices designed to remove rain and debris from a vehicle's windshield, enhancing driver visibility and road safety. Legally mandated in most regions, nearly all automobiles are equipped with wipers. 2. Functions of windshield wipers: (1) All vehicles come with wipers. Rear windows of hatchbacks and SUVs often feature wipers as well. Beyond cars, other transport modes like trains and trams also utilize wipers, along with heavy machinery such as cranes. (2) Regular wiper usage necessitates checking washer fluid levels; immediate refill is required if levels are critically low. Even during dry weather, reduced windshield clarity—especially noticeable at night when dust scatters light—calls for using the washer function to maintain optimal visibility.
Was this review help?
16
5
Share
Marilyn
08/10/25 10:57am
I've been driving a Tesla Model 3 for over a year and am very familiar with the wiper switch position. It's on the control stalk to the right of the steering wheel - not the traditional up-and-down lever type, but a push-button design. To activate the wipers, just gently press the button on top of the stalk; press it again to stop. For auto wiper mode, you need to first set the wiper sensitivity on the car's central touchscreen - just a few taps to enable it. During light rain, it automatically senses precipitation which is quite convenient. I occasionally forget to check the washer fluid level, so I recommend keeping a spare bottle in the trunk. When pressing the stalk, it also sprays cleaning fluid. These thoughtful little design touches for rainy driving don't interfere with one-handed operation or visibility safety. Overall, the Model 3 feels very modern with all controls consolidated onto the stalks and touchscreen.
Was this review help?
11
1
Share
Expand All
VonJustin
09/22/25 4:42am
As a tech enthusiast, I particularly admire Tesla's intelligent design. The windshield wiper control is located on the right stalk of the steering wheel – just press that small button to operate it. The Model 3 doesn't have a traditional dedicated wiper stalk; it's integrated into the multifunction control stalk, making operation simple and clean. What I appreciate most is the automatic wiper function, which uses sensors on the windshield to detect rainfall intensity. You can adjust the sensitivity and speed on the touchscreen, eliminating the need for manual distraction. When driving on highways during rain, the system automatically adjusts the wiping frequency, which is quite convenient. Additionally, there are options in the settings to upgrade wiper modes, such as the cleaning mode for washer fluid spray. Remember to maintain the rubber blades regularly to prevent squeaking. Smart cars really consider every detail – this kind of design minimizes driving distractions.
Was this review help?
12
2
Share
Expand All
VonAndrew
11/05/25 8:02am
As a new driver who just got my license, I chose the Model 3 and was initially confused about finding the wiper switch. After some exploration, I discovered it's on the long stalk on the right side of the steering wheel - just press the round button at the very top. Press once to activate the wipers in rainy conditions, and press again to stop them. You can see wiper settings on the screen, but I usually just use the basic controls. At first, the position felt odd, but once accustomed, it's quite easy to locate without obstructing driving visibility. The straightforward operation suits beginners like me well, preventing accidental touches.
Was this review help?
13
4
Share
Expand All
More Forum Discussions

How to Start a Geely Car When the Battery is Dead?

You can either charge the car battery before starting or call for a rescue vehicle to jump-start it. Here are some precautions regarding car batteries: 1. Check the Battery Cover: Regularly check if the small holes on the battery cover are ventilated during daily driving. If these holes are blocked, the generated hydrogen and oxygen cannot escape, and when the electrolyte expands, it may rupture the battery casing, affecting the battery's lifespan. The typical lifespan of a car battery is around two years. 2. Replenish Power in Time: If the car is left unused for an extended period, start it periodically to recharge the battery to prevent it from becoming unusable due to prolonged power loss. Continuously using the starter when starting the car can damage the battery due to excessive discharge. The correct method is to limit each starting attempt to no more than 5 seconds, with intervals of at least 15 seconds between attempts.
6
1
Share

What is the Definition of Lane Change Completion?

A lane change is considered complete when the vehicle inevitably deviates and crosses the original lane divider, then adjusts its direction to proceed along the new lane, establishing a state of driving along the new lane. Below are precautions for lane changing: Avoid the habitual release of the accelerator during a lane change, which may cause gear disengagement; Yield to vehicles in the lane you are entering; Do not change more than two lanes at once; When vehicles from both the left and right lanes are changing into the same lane, the vehicle on the left must yield to the one on the right. Below are the evaluation criteria for lane changing in Subject 3 of the driving test: 1. Before changing lanes: Failing to observe the traffic conditions behind through the interior and exterior rearview mirrors results in disqualification. 2. During the lane change: If the judgment of the vehicle's safe distance is unreasonable and hinders the normal driving of other vehicles, it results in disqualification. 3. Turn signal usage: Failing to use or incorrectly using the turn signal before changing lanes deducts 10 points. Turning the steering wheel less than 3 seconds after activating the turn signal before changing lanes deducts 10 points.
12
0
Share

What Causes the ABS and Exclamation Mark Lights to Illuminate?

ABS light can illuminate in various states, with different causes and solutions for each state. The details are as follows: State 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the contaminants from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections between system wires or poor contact of the ABS relay, leading to system malfunction. Solution: Check wire connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases and voltage rises, the ABS light turns off. This can also occur if the ABS system's power supply voltage is too low, such as due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity, inspect the charging system, and examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact of the ABS hydraulic valve body; poor contact of the ABS hydraulic valve body wire connector; ABS computer malfunction. Solution: Loosen and retighten the grounding screw of the hydraulic valve body, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact of the brake light. Solution: With the engine running, press the brake pedal, push the brake switch linkage down fully with a finger, then release the brake pedal to complete self-positioning; replace the brake light switch if necessary. If the ABS warning light is on, it is advised not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's path, posing significant safety risks.
16
1
Share

What model is BH7161HAY in the Elantra series?

BH7161HAY is the 2012 Hyundai Elantra 1.6L automatic DLX Premium model. Below is relevant information about BH7161HAY: 1. Manufacturer: Beijing Hyundai Motor Co., Ltd. Since its establishment in 2002, Beijing Hyundai has gone through approximately 17 years of development. As the first joint venture after China's accession to the WTO, Beijing Hyundai has grown and developed rapidly with the momentum of industrial development. Currently, Beijing Hyundai has surpassed the milestone of annual production and sales of 1 million vehicles. Under the guidance of the brand strategy "From Hyundai to the Future," it is striving towards the goal of "becoming the most beloved brand among Chinese people." 2. System: The BH7161HAY features a three-box four-door passenger car body style. Its powertrain consists of a 1.6L G4ED/G4FC/G4FG (Elantra models) inline four-cylinder engine with power outputs of 82/90.4/93.8 kW gasoline engine, gasoline engine, and automatic transmission. The restraint system includes driver-side front airbag and passenger-side front airbag.
7
4
Share

Is it necessary to have a car driver's license for one year before applying for a motorcycle driver's license?

If you have just obtained a driver's license, you must wait until the one-year probation period is over before applying for an additional license. Additionally, there should be no record of accumulating 12 penalty points in the current scoring cycle or the one before applying. If you do not have a driver's license and wish to apply for a motorcycle driver's license, you can register at the local traffic police vehicle management office. According to the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses," motorcycle driver's licenses are divided into three types: D, E, and F. Among them, D is for ordinary three-wheeled motorcycles, E is for ordinary two-wheeled motorcycles, and F is for light motorcycles. Upgrading from a C1 license to a motorcycle license requires passing four subjects, and the examination process is the same as directly applying for a motorcycle license. The examination subjects are as follows: Subject 1: Examination on road traffic safety laws, regulations, and related knowledge. Subject 2: Field skills test, including pile test, slope fixed-point parking and starting, and passing a single-plank bridge. Subject 3: The content of Subject 3 is determined by the provincial public security traffic management department, and there is no unified standard. Subject 4: Examination on the requirements of safe and civilized driving, safe driving skills under complex conditions, and emergency response knowledge.
6
2
Share

How Many Liters of Engine Oil Does a Cruze Need?

The Chevrolet Cruze requires approximately 4 liters of engine oil. The recommended oil type is 5W30. During maintenance, ensure not to overfill or underfill the oil, as this can negatively impact the engine. For oil brands, you can choose from options like Mobil, Shell, or Castrol. Engine oil viscosity changes with temperature, so it's crucial to pay attention to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means the oil can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, ensuring smoother cold starts for the vehicle. The latter number represents the oil's kinematic viscosity at 100°C. A higher value indicates better viscosity retention under high temperatures, which can also be interpreted as superior lubrication performance in high-temperature conditions. When selecting engine oil, keep the following points in mind: Choose oil based on the engine's requirements. It's unnecessary to use overly advanced oil in engines with lower requirements, and similarly, lower-grade oil should not be used in high-demand engines. Opt for multigrade oil whenever possible. Multigrade oils are economical, have a long lifespan, and are highly efficient, offering better protection for the engine. Due to their characteristics, multigrade oils may appear darker prematurely and exhibit lower oil pressure compared to conventional oils, both of which are normal.
10
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.