···
Log in / Register

Where is the windshield washer fluid reservoir located in the Model 3?

4 Answers
SanFrank
09/06/25 7:20am

The windshield washer fluid reservoir in the Model 3 is located on the left side of the engine compartment. Below are specific details about the Model 3: 1. Configuration: The Model 3 is equipped with an all-wheel-drive system, capable of reaching a top speed of 155 mph. Additional radar and cameras can identify pedestrians and road signs, enabling features such as automatic parking, highway autopilot, and traffic jam assist. 2. Performance: The most significant change for drivers and passengers is the upgrade from the previous two-wheel drive to a four-wheel all-wheel-drive system. This is supported by two motors: one motor drives the rear wheels, while a smaller motor drives the front wheels. The 0-100 km/h acceleration time has been improved to 3.2 seconds compared to previous versions.

Was this review help?
17
3
Share
NoraFitz
09/18/25 6:58am

Last time I drove my Model 3 on the highway, I noticed the windshield washer wasn't working well. I figured it was time to refill the washer fluid, but it took me a while to find the filler port under the front hood. The exact location is after opening the front trunk, look for a small blue cap with a windshield washer symbol in the driver's side corner. Remember to first tap 'Controls > Service > Front Trunk' on the touchscreen to unlock the hood, then apply some force to lift it open from the center. Just unscrew the cap to refill - I recommend using dedicated washer fluid to avoid nozzle clogs. Don't fill beyond the MAX line as overflow can damage components. Typically needs refilling every two months, and use antifreeze type in winter. Honestly it's super easy to DIY and saves you the hassle of queuing at service centers.

Was this review help?
12
4
Share
Expand All
OBrooklyn
11/01/25 7:25am

The first time I drove a Tesla, I was also confused and spent a long time looking for the windshield washer fluid port. It's located on the inner left front side of the frunk, with a very noticeable blue twist-off cap. You need to open the front hood by tapping the control on the center touchscreen, as there's no physical switch in the traditional fuel car position. The cap is designed in blue specifically to distinguish it from coolant and battery fluid—don't mix them up. I used regular windshield washer fluid bought from the supermarket and filled it about halfway; it worked fine. Keep an eye on the spray intensity; if it weakens, it's time to refill. I've heard that overly viscous washer fluid can interfere with the automatic wipers, so it's best to choose the type recommended in the manual.

Was this review help?
7
4
Share
Expand All
StCassidy
12/15/25 7:33am

The Model 3 windshield washer fluid filler is hidden in the left corner of the frunk. Just pop the hood and you'll see the blue plastic cap. Here's the three-step process: First, unlock the frunk via the touchscreen, lift it manually, then twist open the cap with the washer symbol to refill. We recommend checking the fluid level during every car wash to avoid running dry on long trips. Northern drivers should switch to winter formula to prevent frozen lines. DIY refills save you $50 compared to dealership service - takes just five minutes.

Was this review help?
18
3
Share
Expand All
More Forum Discussions

Can't the Brake Be Depressed When the Car Battery Is Dead?

When the car battery is dead, the brake cannot be depressed. The reasons why the brake cannot be depressed are as follows: 1. Air in the brake fluid line: Brake fluid is the medium for transmitting force in the braking system. If air enters the fluid line, the brake fluid under high pressure will appear insufficient in strength. Although there is still braking force, the maximum braking force is significantly weakened. In this case, the braking system should be promptly bled at a repair shop. 2. Brake fluid not replaced for a long time: If the brake fluid is not replaced in time, it will contain excessive impurities and moisture, which will affect the transmission of braking force. 3. Oil leakage or overly soft brake material: Generally, oil leakage from the brake master cylinder or brake fluid line will cause the vehicle's brake to become soft. If the brake material is too soft, its high-temperature stability will deteriorate, which will also cause the vehicle's brake to become soft.
17
1
Share

What Causes Water Leakage in the Rear Seats of a Car?

The specific reasons for water leakage in the rear seats of a car are as follows: 1. Poor sealing of the trunk rubber strip leading to water leakage. 2. Blockage of the drainage holes in the trunk lid causing water to leak into the rear seats. 3. Poor sealing of the tail lights resulting in water leakage into the rear seats. 4. Inadequate sealing of the drainage holes beneath the spare tire well leading to water leakage into the rear seats. Solutions: 1. Clear the drainage holes: If you hear noticeable water sounds when opening/closing doors or while driving, it indicates water accumulation in the trunk. Simply use a thin wire or small screwdriver to clear the drainage holes. 2. Replace the sealing strips: Replace the sealing strips for the trunk and rear doors to enhance the car's sealing and prevent further water leakage. 3. Visit a 4S shop for inspection and repair.
15
1
Share

Can uneven car touch-up paint be sanded?

If the car touch-up paint is not smooth after application, it can be sanded. Below is more information about car touch-up paint: 1. Process: The specific steps for touch-up paint include determining the repair area, assessing the damage level, applying protective measures, surface preparation, masking and degreasing, applying base coat, applying clear coat, blending the edges, baking, and finally sanding and polishing the paint surface. If loss of gloss occurs during polishing, it can be restored using a high-speed polisher with specialized polishing compound. 2. Precautions: The hardness of the touch-up paint is lower compared to the original factory paint, and high water pressure can damage the car's paint surface, so avoid using high-pressure water jets directly on the car body.
14
0
Share

What Causes a Car Sunroof to Leak?

Car sunroof leakage can be attributed to the following reasons: 1. Clogged sunroof drainage outlets: When the drainage outlets are blocked, rainwater cannot flow smoothly and gradually seeps into the car. This issue mainly occurs when the owner neglects regular cleaning of the roof, allowing debris to flow with rainwater into the drainage outlets and clog them. To address this, you can use a wire to create a hook and remove the debris from the drainage holes, or visit a repair shop to use an air gun to blow out the debris. 2. Damaged sunroof seal: The sunroof seal is made of rubber and can deteriorate over time due to aging and repeated friction from the sunroof glass, leading to poor sealing and leaks during rainy weather. Regular inspection of the seal's condition is necessary, and damaged seals should be replaced promptly with high-performance, aging- and corrosion-resistant options. 3. Roof deformation: If the car is involved in a collision, the body may deform. If the repair is not done properly, the sealing may not be restored, resulting in leaks. During the repair of accident-damaged cars, it is essential to strictly adhere to the original vehicle standards to prevent mismatched parts and potential leakage issues.
17
5
Share

What is the maximum allowable size for a car spoiler modification?

Car spoiler modifications must not exceed 300mm. Below is an introduction regarding illegal modifications: 1. Penalties: Driving an illegally modified vehicle on public roads will result in the vehicle being impounded by traffic authorities, confiscation of illegal modifications, orders to restore the vehicle to its original condition, and legal fines. 2. Regulations: Vehicles with illegal modifications will not be issued a safety inspection compliance certificate by traffic authorities. If the modifications constitute a violation of public security management laws, public security authorities may impose fines, detention, or other penalties in accordance with the "Public Security Administration Punishment Law." When modifying your vehicle, it is essential to apply for a modification registration with the traffic management department of the public security authorities to ensure the vehicle can pass annual inspections and routine safety checks after modification.
2
2
Share

What are the penalty items for ramp driving?

Penalty items for ramp parking are as follows: 1. Vehicle starting: (1) If the vehicle rolls back 10-30 cm after starting, 10 points will be deducted. (2) If the vehicle rolls back more than 30 cm after starting, the test will be failed. 2. Vehicle stopping: (1) If the front bumper of the car or the front axle of the motorcycle is not aligned with the pole line after stopping, and the deviation exceeds 50 cm, it will be considered a failure. (2) If the front bumper of the car or the front axle of the motorcycle is not aligned with the pole line after stopping, but the deviation does not exceed 50 cm, 10 points will be deducted (previously 20 points). (3) If the vehicle body is more than 30 cm away from the road edge line after stopping but does not exceed 50 cm, 10 points will be deducted (previously 20 points). (4) If the vehicle body is more than 50 cm away from the road edge line after stopping, 100 points will be deducted. 3. Other penalty items: (1) If the engine stalls once due to improper operation, 10 points will be deducted. (2) If the parking brake is not tightened after stopping, 10 points will be deducted. (3) If the vehicle rides or presses the solid edge line of the road while driving, it will be considered a failure.
9
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.