Where is the windshield washer fluid outlet of BYD F3 located?

1 Answers
DelKimberly
07/30/25 3:47am
BYD F3's windshield washer fluid outlet is located next to the engine radiator, with a capacity of 3.3L. When the washer fluid is low, the car's dashboard will display a corresponding warning, allowing the owner to refill it themselves. Windshield washer fluid is a cleaning solution for car windshields, a consumable item mainly composed of alcohol, water, ethylene glycol, corrosion inhibitors, and various surfactants. The BYD F3 is a compact car launched by BYD, measuring 4533mm in length, 1705mm in width, and 1490mm in height, with a wheelbase of 2600mm. It is equipped with a 1.5L naturally aspirated engine producing a maximum power of 80kw, paired with a 5-speed manual transmission.
Was this review help?
14
0
Share
More Forum Discussions

How to Test if a Parking Sensor is Working Properly?

You can roughly determine which sensor is malfunctioning by comparing the presence and volume of beeps between several sensors. Parking sensors have blind spots, and in actual maintenance, you can use these blind spots to approach a specific sensor to check for faults. When a parking sensor fails, it will emit a long intermittent "beep" sound to indicate a malfunction in the left sensor.
12
1
Share

How are the fast and slow lanes divided on highways?

Located in the innermost lane of the highway. Only when the road meets the standards of a two-way six-lane highway is there an overtaking lane. For two lanes in the same direction, the left lane is the fast lane and the right lane is the slow lane; for three or more lanes in the same direction, the leftmost lane is the fast lane.
10
3
Share

How to reset Volkswagen service reminder?

With the engine turned off, press and hold the short-distance trip meter reset button located below the tachometer. Turn the ignition switch to the ON position, then release the short-distance trip meter reset button. The "SERVICE" indicator will appear on the display. Locate the clock button and pull out the minute adjustment button on the clock. Turn the minute button clockwise until the odometer reading appears on the display. Turn off the engine to reset the reminder message. Then turn the ignition switch to the ON position again.
1
3
Share

How to Repair Scratches on Windshield Caused by Sandpaper?

For small and shallow scratches, they can be removed by polishing. However, it's best if the scratches are not within the driver's line of sight. Slowly apply the gel along the glass crack to let it seep into the crack, but note that glass repair agents are only suitable for minor scratches. If the glass scratches are deep, it is recommended that the car owner choose a reliable and reputable professional repair shop for the repair.
10
2
Share

What to Do When the Ford Edge Rear Tailgate Won't Open?

First, check whether the related circuits, fuses, contacts, etc. are functioning normally and if any product configurations are damaged. It is necessary to confirm and conduct repairs at a professional maintenance shop. If no faults are found, the intermittent malfunction might be caused by improper operation during daily use. You can try manually opening the tailgate and initializing the system.
19
3
Share

When to Use Blending Clear Coat?

Apply the blending clear coat within 3 minutes after spraying the glossy clear coat. The blending clear coat only needs to be sprayed in 2 to 3 layers at the interface between the new and old paint, at a distance of about 15cm. After car paint repair, there will inevitably be some color difference between the repaired paint and the original car paint. At this time, the blending clear coat is needed around the repaired area to create a transition and eliminate the visual color difference. The glossy clear coat is used to beautify and add gloss to the paint surface after repair. Precautions for storage and use of blending clear coat: 1. Mixing ratio: Ready to use without mixing; 2. Spray gun pressure and tools: Gravity feed spray gun with 2bar pressure and 1.2 to 1.5mm nozzle, suction feed spray gun with 1.4 to 1.7mm nozzle; 3. Application method: After completing the paint repair, lightly spray a layer of blending clear coat at the interface immediately, then lightly spray another layer after 15 seconds; 4. Suitable for: 2K topcoat, two-component clear coat; 5. Not suitable for: 1K base coat; 6. Shelf life: Can be stored for more than 2 years when tightly sealed, storage temperature is 20 degrees Celsius.
19
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.