Where is the VIN located on a Toyota Highlander?

1 Answers
VonSilas
07/30/25 5:47am
Toyota Highlander's VIN is located at the lower left corner of the windshield on the driver's side. The VIN is a unique set of seventeen alphanumeric characters used to identify the vehicle's manufacturer, engine, chassis number, and other specifications. Here is some relevant information about the VIN: 1. Introduction: The VIN (Vehicle Identification Number or chassis number) is a unique set of seventeen letters or numbers used to identify a vehicle's manufacturer, engine, chassis number, and other specifications. 2. Note: To avoid confusion with the numbers 1, 0, and 9, the letters "I", "O", and "Q" are not used. Additionally, the 10th digit, which represents the model year, does not use "I", "O", "Q", "U", "Z", or "0".
Was this review help?
7
0
Share
More Forum Discussions

What causes both the ABS and tire pressure warning lights to illuminate simultaneously?

ABS warning light can indicate various conditions, each with different causes and solutions, as detailed below: Condition 1: ABS warning light remains constantly illuminated (most common). Cause 1: The ABS wheel speed sensor's detection area is contaminated by mud, sludge, or other pollutants, affecting its ability to read wheel speed signals. This prevents the ABS control unit from determining vehicle speed or calculating wheel slip rates, thus failing to issue proper braking commands. Solution: Clean the wheel speed sensor and adjust its clearance with the tone ring to restore normal function. Cause 2: Loose wiring connections or poor ABS relay contact causing signal interference. Solution: Inspect all wiring connections and secure any loose terminals. Condition 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: Battery voltage drops below 10.5V when multiple electrical components are in use. The light extinguishes when engine speed increases voltage. Possible low voltage supply to ABS system due to poor connections or grounding issues. Solution: Check battery specific gravity, charging system, and power supply connections (including voltage relays). Condition 3: ABS warning light stays on after engine start until ignition is turned off. Cause: Poor grounding of ABS hydraulic valve body; faulty wiring connections; or ABS control module failure. Solution: Loosen and retighten valve body ground screws (clean contact surfaces if necessary); inspect connector gaps; replace ABS/ASR control module if needed. Condition 4: ABS warning light activates during high-speed driving. Cause: Significant discrepancy between front and rear wheel speed readings; incorrect tire or wheel rim specifications. Solution: Verify proper tire and wheel rim specifications as indicated on the fuel filler door placard. Condition 5: ABS warning light flashes intermittently. Cause: Improper brake light switch adjustment; internal switch contact failure. Solution: With engine running, fully depress brake pedal while manually pushing switch lever downward to reset position; replace brake light switch if necessary. Important: When the ABS warning light is illuminated, discontinue driving immediately. ABS failure compromises wheel anti-lock braking functionality, potentially causing wheel lock-up during emergency braking, resulting in loss of vehicle control and trajectory adjustment capability, posing significant safety risks.
4
1
Share

What does 12 fuel consumption mean?

12 fuel consumption refers to the amount of fuel consumed by a car when driving 100 kilometers at a constant speed. 12 fuel means that the car consumes 12 liters of fuel per 100 kilometers. Observing instantaneous fuel consumption is of great significance for understanding the fuel consumption of the engine under different conditions. You should consider whether your driving habits are too aggressive, such as emergency braking, fluctuating speeds, or seizing every gap, as these driving habits can also increase the car's fuel consumption. By observing instantaneous fuel consumption, you can understand the fuel consumption when the vehicle is stationary and the engine is idling; through instantaneous fuel consumption, you can understand the fuel consumption per 100 kilometers at different speeds, thereby finding the vehicle's economical speed; for some vehicles with computer-controlled fuel injection, instantaneous fuel consumption can show that the fuel consumption is "0" when coasting in gear (the fuel injector stops injecting fuel). If it is not a sudden increase in instantaneous fuel consumption but an increase in average fuel consumption, you should consider whether the car has a malfunction, such as excessive carbon deposits in the engine, a damaged oxygen sensor, long-unreplaced "three filters," a problem with a certain engine control unit, or insufficient tire pressure. These can all cause a sudden increase in car fuel consumption, accompanied by a decrease in power performance and changes in exhaust color. If it is a car-related issue, it is recommended that the owner go to a 4S shop for inspection and repair. Regular maintenance can also keep the car in good working condition.
18
4
Share

Can I go to a 4S shop for maintenance after servicing outside?

You can go to a 4S shop for maintenance after servicing outside. Car maintenance items: Major maintenance items include engine oil, oil filter, air filter, and fuel filter. As for spark plugs, brake fluid, and transmission fluid, there is no fixed mileage for replacement. Major maintenance is based on minor maintenance, and in addition to engine oil and oil filter, air filter and fuel filter are also replaced. These two filters serve to filter dust from the air and impurities from the fuel. Benefits of car maintenance: Ensures driving safety, reduces vehicle fuel consumption, extends the lifespan of the car, and reduces the failure rate of car components.
20
2
Share

What are the two modes of the CFMoto 250?

The CFMoto 250 offers two driving modes: S mode, also known as Sport mode, and E mode, also referred to as Eco mode. Differences between the two power modes of the 250sr: This motorcycle features a Sport mode and an Eco mode. When switched to Eco mode, the motorcycle's power response slows down, and the throttle reaction becomes slightly more sluggish, but fuel consumption is reduced. CFMoto 250 engine specifications: This motorcycle is equipped with a single-cylinder engine that delivers a maximum power of 20.5 kW at 9,750 rpm and a maximum torque of 22 Nm at 7,500 rpm. The engine has a bore of 72 mm and a stroke of 61.2 mm.
8
4
Share

Is 12 Fuel Consumption Considered High?

Whether it is considered high fuel consumption depends on different vehicles and driving conditions. For off-road vehicles or large SUVs, 12 fuel consumption is normal. However, for small cars, 12 fuel consumption is indeed a bit high. Here are the details: Fuel-saving methods: When driving on the road, the most fuel-consuming situation is stop-and-go driving with frequent braking. The more brakes are applied, the more fuel is consumed, so driving on urban roads is the most fuel-intensive. Maintaining a steady speed results in smoother driving and lower fuel consumption. The most economical driving speed is between 50 to 60 km/h. Meaning of 12 fuel consumption: 12 fuel consumption refers to the amount of fuel consumed by the car when driving 100 kilometers at a constant speed. 12 fuel consumption means the car consumes 12 liters of fuel per 100 kilometers.
7
1
Share

What is the minimum character height for off-road vehicle nameplates?

The character height on off-road vehicle nameplates should not be less than 5mm. Vehicle nameplates include: Vehicle nameplates are identification plates that indicate the basic characteristics of a vehicle, mainly including the manufacturer's brand, model, engine power, total mass, load capacity or passenger capacity, factory serial number, manufacturing date, and manufacturer's name. Function of vehicle nameplates: The manufacturing date can be determined by consulting the user or by inspecting the vehicle nameplate, as the vehicle's manufacturing date is always indicated on the nameplate located in the driver's compartment. Location of vehicle nameplates: Vehicles must be equipped with product nameplates placed in an easily observable position at the front of the vehicle. For buses, the nameplate is positioned above the front passenger door inside the vehicle.
13
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.