Where is the VIN located on a GL8?

2 Answers
BethanyDella
07/29/25 5:55am
The VIN is located next to the windshield wiper strip at the lower edge of the front windshield seal in the engine compartment. It is crucial to carefully inspect the VIN when purchasing a vehicle, whether new or used, as confirming the manufacturing date is an essential step. Below are detailed steps to locate the VIN: 1. First, locate the hood release lever on the lower left side of the driver's compartment and pull it to unlock the engine hood. 2. Then, find the latch under the hood and lift it to open the engine compartment. 3. Use the hydraulic strut to prop up the engine hood, revealing the layout of the engine compartment. 4. Inside the engine compartment, you can find both the engine number and the VIN.
Was this review help?
17
3
Share
AngelinaLynn
08/12/25 9:25am
I know this well! The GL8's VIN (Vehicle Identification Number) can be found in several locations. The most obvious spot is the lower left corner of the windshield—you can see a 17-digit alphanumeric code printed there when standing outside at the front of the car. If the windshield tint makes it hard to read due to glare, simply open the driver's door and check the silver label near the door sill; it’s definitely there. For some model years, the GL8 hides the VIN under the front passenger seat—lift the carpet, and you might find it engraved on the metal frame. If you still can’t locate it, refer to the owner’s manual, which specifies all possible positions. This number is often needed for vehicle registration or repairs—avoid wiping it with tissue paper; instead, use a rubbing paper or tape to lift the imprint for better clarity.
Was this review help?
8
1
Share
Expand All
More Forum Discussions

How to Pair a Car Remote Key?

Get into the car and close all doors. Open the driver's door, insert the key, and turn it on and off five times in a row. On the fifth time, the hazard lights will flash once. Simultaneously press and hold the lock and unlock buttons on the remote key you want to pair, and press them several times. The hazard lights will flash, and if they flash twice, it means the remote key has been successfully paired. Remove the key and test it to ensure both the lock and unlock buttons are functioning properly. Notes: A. Pairing methods may vary depending on the car brand and model; B. When purchasing a car remote key, choose a reputable and certified brand to prevent data theft.
2
5
Share

Who Generally Pays the Transfer Fee for Used Cars?

The transfer fee for used cars, also known as the used car transaction service fee, is negotiated between the buyer and seller and submitted to the local government. Here are the precautions for car transfer: Check the Vehicle Certificate: Inspect the embossed number, engine number, and registration date on the vehicle certificate, and also check for any signs of alteration. Check the Original Tax Receipt: Make sure to check the original tax receipt for the vehicle purchase tax. Some cars may not have paid the purchase tax originally, and after the transfer, these unpaid or tax-exempt vehicles may be required to pay the outstanding purchase tax. Ensure Complete Documentation: The insurance transfer should be completed promptly along with the used car transfer procedures. Understand the Vehicle's Condition: Vehicles that are mortgaged or under supervision are prohibited from being traded. Vehicle information can be checked through the vehicle management office.
7
3
Share

What to Do When the Car Malfunction Indicator Light Comes On?

When the car malfunction indicator light comes on, it indicates that there may be a mechanical issue with the engine, and you should immediately take the vehicle to a 4S shop for repair. Here are the reasons why the car malfunction indicator light may illuminate: Starting system malfunction preventing the engine from turning or turning too slowly: Insufficient battery charge, loose or severely oxidized battery terminal clamps, blown main circuit fuse, or faulty ignition switch. Ignition system malfunction: Poor performance of the ignition coil, resulting in weak or no high-voltage spark. Fuel injection system malfunction: Empty fuel tank, non-operational fuel pump or low pump pressure, leaking or deformed fuel lines, or disconnected circuit relay. Intake system malfunction: Faulty idle control valve or its control circuit, cracked idle control valve air pipe or leaking connections, or malfunctioning air flow meter.
6
5
Share

How many liters of engine oil does the X-Trail require?

The Nissan X-Trail with a 2.0L displacement generally requires approximately 3.8 to 4 liters of engine oil. Below is some relevant information about the X-Trail: Exterior Design: The new X-Trail adopts the "Fluid Sculpture" design concept, marking a significant departure from the previous model's boxy, rugged style. The vehicle features dynamic and fluid lines that flow seamlessly from front to rear. Interior: Similar to its exterior, the new X-Trail's interior incorporates more rounded lines. Nissan's signature home-like cozy interior style is also reflected in the new X-Trail. Compared to the rigid design of the previous model, the overall interior of the new vehicle is more fashionable and exudes a greater sense of luxury.
4
1
Share

Which gear should an automatic car be in when waiting at a red light?

When waiting at a traffic light in an automatic car, if the expected wait time is within 20 seconds, you can use D gear along with the foot brake. For situations with traffic congestion where the wait exceeds 30 seconds, shift to N gear and engage the handbrake. Below is relevant information about the N gear in cars: Main purpose: In automatic transmission models, engaging N gear creates a power interruption effect similar to shifting to neutral in manual transmissions, though there are some differences. Precautions: Automatic cars should not coast in neutral under non-special circumstances, as it is not only unsafe but can also lead to transmission failure due to insufficient lubrication of gears and other components caused by inadequate oil supply from the transmission oil pump.
16
1
Share

How to Add Windshield Washer Fluid to a Car?

Steps to Add Windshield Washer Fluid to a Car: Park the Car: First, engage the handbrake to prevent the car from moving while adding windshield washer fluid. Open the Hood: Pull the front hood release lever located near the driver's side footwell to ensure the hood can be opened. Lift the hood and locate the windshield washer fluid reservoir. Open the Reservoir and Add Fluid: Open the cap of the windshield washer fluid reservoir. Pour in an appropriate amount of fluid, observing the fill line to avoid overfilling. Stop when the fluid reaches the marked line. Precautions: Avoid overfilling the reservoir. If you notice some foam around the opening, there’s no need to worry—it won’t affect the fluid’s performance. If the car is used in northern regions during winter, be sure to use antifreeze-type windshield washer fluid. For southern regions, a standard fluid with bug remover additives is usually sufficient.
10
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.