Where is the vehicle's radiator support located?

1 Answers
VonNorah
07/30/25 8:11am
The vehicle's radiator support is located at the front section of the car, primarily used to secure the radiator. Below are specific details about the automotive radiator support: 1. Fault diagnosis of radiator support: Installed at the front, the radiator support holds the radiator and cooling mesh. Damage to the radiator support indicates frontal collision, and in most cases, such damage involves related components including the bumper, crash beam, radiator, grille, headlights, and engine hood. 2. Definition of radiator support: Commonly referred to as the radiator frame or front frame, it differs from the grille (which is the air intake area). The radiator support is a structure designed to mount components like headlights and radiator. For example, pickup trucks also have a similar structure at the rear cargo area called a roll bar or roll cage.
Was this review help?
14
3
Share
More Forum Discussions

Reasons for Audi Intake Flap Stuck in Open Position

Audi intake flap stuck in open position is caused by damaged position sensor or intake manifold failure. The details are as follows: 1. Throttle position sensor: The throttle position sensor monitors the opening angle of the throttle valve to determine idle, full load, acceleration/deceleration conditions, and implements corresponding fuel injection control based on throttle opening status. 2. Intake manifold pressure sensor: The intake pressure sensor provides engine load information by measuring intake pipe pressure to indirectly calculate the air intake volume, then converts it into electrical signals for the ECU through internal circuits. 3. Intake air temperature sensor: Provides air temperature information for fuel injection volume and ignition timing correction. 4. Crankshaft position sensor: Provides engine speed and crankshaft phase information as reference points for fuel injection timing and ignition timing.
15
5
Share

What is the best installation location for adding an inverter to a car?

The best installation location for adding an inverter to a car is inside the car's cigarette lighter socket. Here are the relevant details: 1. Car inverter: (Switch power converter, Power-Inverter) is a device that can convert DC12V direct current into AC380V alternating current with the same voltage, for use by general electrical appliances. It is a convenient vehicle power converter. 2. Precautions: To ensure safety, it is recommended that when using a high-power inverter, the ground wire clip should be attached to some metal material connected to the wall or the ground to prevent leakage or generate static electricity.
13
3
Share

Is the Audi Q5L a Class C or B?

The Audi Q5L is a Class B vehicle. Below are the relevant details about the Audi Q5L: 1. Exterior: It adopts Audi's new design language, with changes to the headlights and grille style, giving it a more youthful and sporty appearance overall. The new model will continue to offer two different exterior styles for consumers to choose from. The dimensions of the Audi Q5L are 4770mm in length, 1893mm in width, 1667mm in height, with a wheelbase of 2907mm. 2. Configuration: In addition to featuring leather seats in lower trim models, it also includes dual-tone seats, ambient lighting, and other configurations. For the driving system, it adds features such as panoramic imaging, intelligent parking, and side assist. 3. Powertrain: The Audi Q5L still utilizes two power variants of the 2.0T engine—low and high power. The low-power version delivers 140kW and 320N·m of torque, while the high-power version offers 185kW and 370N·m of torque, paired with a 7-speed dual-clutch transmission.
3
3
Share

What does the Audi emergency braking warning system indicate?

Audi emergency braking warning system may appear due to reasons such as damaged warning system sensors, radar system failure, or issues with the warning control system. Below are detailed explanations: 1. Audi Basic Occupant Protection System: Tightens seat belts and allows reversible adjustment of front seat belts; If vehicle control is insufficient or excessive, windows and sunroofs close leaving only a small gap; Activates hazard warning lights. The Audi Basic Occupant Protection System is activated when the vehicle speed exceeds 30 km/h. 2. Audi Front Occupant Pre-Safe System: The Audi Front Occupant Pre-Safe System includes all functions of the Audi Basic Occupant Protection System. Additionally, it calculates the possibility of rear-ending the vehicle ahead under system constraints. When a collision risk is detected, the following devices are triggered: Adjusts the electric headrests, head restraints, and pneumatic side bolsters on the front and outer rear seats.
17
3
Share

How to Install a License Plate?

The method for installing a license plate is as follows: On the front and rear of the car, you can see fixed points where the license plate is to be mounted. All fixing screw components must be tightened without any gaps. Once the license plate is in the correct position, tighten all the screws, but do not apply excessive force. The screws should not come loose and should be firm with slight pressure. Align the cap with the spacer and press it inward, applying slight pressure to secure the cap in place. Note that once the screws and caps are fixed, they cannot be removed. License Plate Introduction: License plates, commonly known as vehicle plates, refer to the plates hung on the front and rear of a vehicle. License Plate Materials: The commonly used materials are aluminum, iron, plastic, or paper, on which the vehicle's registration number, registration region, or other relevant information is engraved.
20
4
Share

How Many Years Is a New Car Exempt from Inspection?

New cars fall under the 6-year inspection exemption policy. However, according to national regulations, owners still need to visit the vehicle management office every 2 years to apply for an annual inspection sticker. Failure to obtain this sticker is equivalent to not having the vehicle inspected. Certain documents are required to apply for the exemption. For private vehicles over 10 years old, the original inspection cycle still applies: once a year for vehicles aged 10 to 15 years, and every six months for vehicles over 15 years old. According to the opinions on strengthening and improving motor vehicle inspection work issued by the Ministry of Public Security and the General Administration of Quality Supervision, Inspection and Quarantine, non-operational passenger cars and other small and mini passenger vehicles within 6 years are exempt from inspection on a trial basis. The exemption policy applies to non-operational passenger cars and other small and mini passenger vehicles, excluding vans and vehicles with 7 or more seats. If an operational motor vehicle passes the safety technical inspection within the specified inspection period, it does not need to undergo a repeat safety technical inspection.
20
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.