Where is the USB port of Wuling Hongguang S located?

1 Answers
LeCarson
07/29/25 11:47am
The USB port of Wuling Hongguang S is located on the right side of the center console panel, covered by a protective cap. Simply open the cap to use it. Taking the 2018 Wuling Hongguang S as an example, its body dimensions are: length 4400 mm, width 1660 mm, height 1750 mm, with a wheelbase of 2720 mm and a fuel tank capacity of 50 liters. The 2018 Wuling Hongguang S is equipped with a 1.2L naturally aspirated engine, delivering a maximum power of 60.3 kW and a maximum torque of 116 N·m. It adopts a front-engine, rear-wheel-drive layout, with a MacPherson strut independent front suspension and a leaf spring non-independent rear suspension.
Was this review help?
19
4
Share
More Forum Discussions

How to Replace the Electronic Parking Brake Pads on an 18 Camry?

Park the Camry on a sturdy and level workshop floor, and support it with a jack. Use a tire wrench to loosen the tire bolts and remove the tire. Press the brake caliper piston back into its housing; a retraction tool may be necessary. Install the new brake pads into the brake caliper and replace the caliper cap. After replacing the brake pads, check the brake fluid level. Finally, test drive the Camry several times to break in the new brake pads.
18
2
Share

Are there discounts for ETC toll fees?

According to the relevant regulations of the State Council, there are discounts for ETC, but the banks handling the process offer greater incentives to promote and encourage ETC adoption. Starting from 2020, vehicles without ETC or not using ETC will not enjoy toll discounts. In the future, only one manual lane will remain at highway toll stations, requiring drivers to pay tolls manually, with lower efficiency compared to ETC lanes. ETC Deduction Principles: There are one or more ETC lanes on highways. Through dedicated short-range microwave communication between the vehicle's on-board electronic tag installed on the windshield and the microwave antenna in the ETC lane, combined with computer networking technology for backend bank settlement, vehicles can pass toll stations without stopping to pay tolls. This is all based on the principle of 'pass first, deduct later.' Benefits of Installing ETC: Time-saving: Eliminates the hassle of waiting in queues; Green and eco-friendly: Low-carbon, as vehicles pass toll stations without stopping, reducing noise and exhaust emissions, thereby minimizing pollution; Reduced wear and tear: Saves costs by decreasing the frequency of vehicle starts and brakes, lowering wear and fuel consumption; Improved efficiency: ETC lanes can theoretically increase passing efficiency by 2-3 times, making traditional ETC faster, more advanced, and high-tech. Compared to license plate payment, ETC technology is more mature and advantageous. More Policy Support: The State Council explicitly stated in the "13th Five-Year Plan for the Development of a Modern Comprehensive Transportation System" that "by 2020, intercity transportation cards will be widely used in key city clusters, and the adoption rate of ETC will significantly increase." It also set a target in the "13th Five-Year" comprehensive transportation development indicators: "By 2020, the ETC usage rate for passenger vehicles on roads should reach 50%. More Future Possibilities: In addition to continuously improving the convenience of ETC installation and usage rates for passenger vehicles, future efforts will focus on promoting ETC adoption for trucks and exploring deeper integration of ETC systems with smart transportation developments such as vehicle-to-vehicle communication and vehicle-road coordination, providing comprehensive travel services for car owners. This means more application scenarios will support ETC usage. ETC Usage Notes: The ETC transaction sensing range is 8 meters. If the vehicle ahead stops, maintain a distance of over 10 meters to prevent accidental toll payment for the vehicle ahead due to ETC device failure or absence. The recognition speed for ETC lanes is 20 km/h. Driving too fast may result in failure to read vehicle device information, leading to deduction failure. Unauthorized removal or movement of the OBU device, or detachment/loosening of the ETC electronic tag, will render the tag invalid. It can be taken to the bank where the ETC card was issued or a highway service office for inspection. Non-deliberate loosening or detachment only requires reactivation. When using a debit card linked to ETC, insufficient balance may cause deduction failure. Follow on-site staff guidance to use manual MTC lanes for cash or card payment. Thick windshields may cause poor signal reception, especially for vehicles with replaced or modified windshields after accidents.
19
5
Share

What to Do When New Car Paint Gets Scratched?

Clean the scratched area thoroughly, use sandpaper to smooth out the scratched area, and then start spraying paint from a certain distance away from the scratch. When noticing paint scratches on the car door, first inspect the damage to determine the extent of the scratch and the level of rust. Before performing DIY paint repair, properly treat the surface by gently sanding off rust spots in straight lines in the same direction, then proceed with paint touch-up using appropriate tools.
18
5
Share

How to set the Q5 side mirrors not to fold when locking the car?

Set it in the MMI system. First, enter the MMI system, then go to the central door lock settings, find the side mirror option, and set it to automatically fold when locking the car. As the widest component installed on the vehicle, side mirrors are most susceptible to impact, hence the need for a folding function.
17
3
Share

How to Check the Oil Level in a 2019 Mercedes-Benz?

Pull the oil dipstick out of the dipstick tube; wipe the dipstick clean; insert the dipstick back into the tube until it stops, then remove it again. Use the multifunction buttons on the left side of the steering wheel. Turn on the ignition. Repeatedly press the system selection button, which is the left and right button. The vehicle should be parked on a level surface; if the engine is at normal operating temperature, turn it off and wait at least 5 minutes.
10
3
Share

How to Fix a Locked Rear Wheel on a Polo?

First, drive forward and backward three times, but avoid making the movements too large. Otherwise, the brake pads and brake drum may not separate, causing the tire to be forcibly dragged and wear out. Pour 100°C boiling water between the brake pads and brake drum. The thermal expansion might cause them to separate automatically, and then you can try the above method again. Gently tap both sides—this might help separate them. If that doesn't work, you can kick the tire a few times, which might also help.
13
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.