Where is the USB port in the Sagitar?

How to Add Windshield Washer Fluid to a Geely Emgrand?

Geely Emgrand windshield washer fluid adding steps are as follows: 1. Open the driver's door of the Geely Emgrand and pull the safety latch of the engine hood; 2. Then press the hidden switch under the engine hood, slowly lift the hood upwards, and secure it with the support rod; 3. Locate the windshield washer fluid filler port (usually on the left side), open the small blue cap, and finally pour in the prepared windshield washer fluid. The functions of windshield washer fluid are as follows: 1. Cleaning performance: Surfactants typically have wetting, penetrating, and solubilizing functions, serving to clean and remove dirt. 2. Antifreeze performance: The presence of alcohol and ethylene glycol can significantly lower the freezing point of the liquid, providing antifreeze protection. 3. Anti-fog performance: Forms a monomolecular protective layer on the glass surface, ensuring clear and transparent windshield visibility. 4. Anti-static performance: After cleaning with washer fluid, substances adsorbed on the glass surface can eliminate surface charges, providing anti-static properties. 5. Lubrication performance: The ethylene glycol content in washer fluid has high viscosity, providing lubrication to reduce friction between wipers and glass, preventing scratches.

18

3

Share

What are the driving wheels and the passive wheels respectively?

Introduction to driving wheels and passive wheels is as follows: 1. The driving wheel is the wheel that converts the energy of the car engine into kinetic energy, enabling the car to move backward or forward. 2. The passive wheel has no power and only plays a supporting role. The rotation of the passive wheel is driven by other driving wheels. The following is the connection between the driving wheels and passive wheels of a car: (1) The driving wheel of a car is connected to the drive axle and provides the power for the car to move forward. (2) The power of the car engine is transmitted through the gearbox to the drive axle and then to the driving wheels, so the function of the drive axle is not only to support the weight of the car but also to provide power for driving. (3) When the car moves forward, the driving wheels are the two front wheels, and the two rear wheels are the passive wheels, which only play a supporting role and do not provide power.

9

0

Share

What is the method to reset the Land Rover maintenance light?

To reset the Land Rover maintenance light, you can use the function button on the right side of the steering wheel. Navigate to the vehicle information on the dashboard and select the 'Latest Alert' option. Simultaneously press and hold the down button on the steering wheel and the 'i' button on the turn signal lever for about 10 seconds to reset it. Below is an introduction to the maintenance light and Land Rover: 1. The maintenance light is a reminder function set by the manufacturer to alert the owner for scheduled maintenance based on mileage or time. It appears as a dashboard or screen message or indicator light. 2. Resetting the maintenance light means clearing the reminder information after completing the maintenance, also known as information reset. 3. Land Rover is a British luxury all-terrain SUV brand founded by Maurice Wilks in 1948.

9

4

Share

When Does the Clutch Need to Be Replaced?

The replacement time for the clutch is not strictly defined and depends on the driving conditions of each vehicle. The following details the service life of the clutch: 1. According to the 'Technical Specifications for Automotive Dry Friction Clutch Assembly QCT25-2004', the clutch, as an important component of the transmission system, can last as long as the vehicle under normal usage. 2. After undergoing 1 million separation endurance tests, the main performance parameters of the clutch assembly still remain at 70% to 90% of the original, indicating that the clutch is highly durable. 3. Experimental statistics show that in urban areas in China, the clutch is pressed approximately 9 times per kilometer, while in suburban areas, it is pressed about 3 times per kilometer. If the driving is evenly split between these two conditions, averaging 6 clutch presses per kilometer, the main components of the clutch still perform well even after 160,000 kilometers.

13

5

Share

What are the main causes of transmission overheating?

The causes of transmission overheating mainly include the following five aspects: 1. High engine and coolant temperature, affecting transmission heat dissipation. 2. Clogged radiator grille. 3. Transmission clutch slippage, generating additional heat. 4. Insufficient flow in transmission cooling oil circuit. 5. Thermostat sticking. Below are the inspection points when transmission temperature is too high: (1) Check whether the transmission is low on oil, whether the radiator fan is rotating, and whether there is oil leakage under the vehicle. (2) It is recommended to change the transmission oil. If the transmission oil relies on the radiator for cooling, check whether the radiator is too dirty.

20

1

Share

What is the tire pressure for the VV6?

The normal tire pressure range for the WEY VV6 is 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and decreased by 0.1 bar in summer. The VV6 is equipped with a tire pressure monitoring system that can monitor tire pressure and temperature in real-time and alert the driver promptly when abnormalities occur, allowing timely action to prevent accidents. By pressing the interface switch button on the steering wheel, the driving display can be switched to the tire pressure monitoring interface to check the tire pressure. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no stamp on top, four small spikes below, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure. The system typically alerts when the pressure is below 1.8 bar or above 3.0 bar. In this case, the tires should be checked and the pressure adjusted. Tire pressure monitoring not reset. After inflating the tires, if the tire pressure is not reset in time, the monitoring system will still record the previous data, causing the indicator light to remain on. Simply reset the tire pressure to resolve this issue. Damaged tire pressure sensor. The tire pressure sensor, which monitors tire pressure, is installed inside the tire and connected to the inflation valve. If the sensor is damaged while driving, the tire pressure warning light will illuminate. In case of sensor damage, the only solution is to replace it with a new one.

10

5

Share

Where is the USB port in the Sagitar?

How to Add Windshield Washer Fluid to a Geely Emgrand?

What are the driving wheels and the passive wheels respectively?

What is the method to reset the Land Rover maintenance light?

When Does the Clutch Need to Be Replaced?

What are the main causes of transmission overheating?

What is the tire pressure for the VV6?

How to Determine Running a Red Light When Turning Left?

What to Do When Water Drips from the Exhaust Pipe After Parking?

How to Reset the Q5I Tire Pressure Warning Light?

Should Freon be added to the car air conditioning system from the low-pressure or high-pressure side?