Where is the USB port in the Lavida?

2 Answers
BeckettAnn
07/24/25 4:44am
The USB port in the older Lavida models is located inside the center console or below the central display screen; the USB port in the all-new Lavida is positioned at the rear air vent. Some versions of the Lavida do not come equipped with a USB port. The car USB is a type of on-board transmission cable that supports hot-swapping, offers flexible connections, is convenient to use, and can provide independent power supply. The Lavida is a sedan produced by Shanghai Volkswagen, launched in June 2008. Taking the all-new Lavida as an example: the vehicle's length, width, and height are 4605mm, 1765mm, and 1460mm respectively, with a wheelbase of 2610mm. Its in-car navigation system combines touch screen and rotary knob controls for operation.
Was this review help?
2
5
Share
MacEloise
08/11/25 12:18am
I've been driving my Lavida for several years, and the USB port is usually located in that small storage compartment under the center console—just lift the cover and you'll spot it immediately. I use it to charge my phone, and the speed is quite fast. Sometimes it's also convenient for connecting Bluetooth to play music. If you can't find it, check your car's configuration—for example, in newer models like the Lavida Plus, there might be an additional port hidden inside the central armrest. Remember to clean the dust from the port regularly to avoid poor contact affecting usage. Also, if you encounter charging issues, try switching to a different data cable—the original one works best. Overall, the location is well-designed, within easy reach from the driver's seat, so you don't have to worry about distractions while driving.
Was this review help?
13
3
Share
Expand All
More Forum Discussions

Reasons for brake noise in Golf 7

Reasons for brake noise in Golf 7 are as follows: 1. Severe brake pad wear: When the brake pads reach the warning line or are worn, the noise is mostly a sharp metal friction sound, accompanied by reduced braking effectiveness. 2. Brake noise caused by brake pad material: Harder brake pad materials are more likely to cause this situation, while softer materials result in less noise, but softer brake pads wear out faster and require more frequent replacement compared to harder ones. 3. Brake noise caused by improper installation of the brake system. Solution for brake noise in Golf 7: Visit a 4S shop for inspection or replace with new brake pads.
9
3
Share

What are the reasons for no response when starting a car?

The reasons for no response when starting a car are: 1. Dead car battery; 2. Steering wheel in locked position; 3. Gear not in neutral or P position when parking; 4. Insufficient fuel; 5. No antifreeze added; 6. Ignition lock damage; 7. Starter relay damage; 8. Starter motor damage; 9. Starter fuse blown; 10. Insufficient fuel pressure; 11. Incorrect throttle position sensor signal; 12. Poor fuel pump operation; 13. Poor spark plug operation; 14. Poor distributor operation; 15. Excessive carbon buildup in vehicle; 16. Motor failure; 17. Fuel injector problem.
17
2
Share

Do All Older Highlander Models Burn Oil?

Most vehicles experience some degree of oil burning, with the key difference being the amount consumed. Engine oil naturally has a certain consumption rate, and excessive consumption indicates an oil burning issue. Here are the main causes of oil burning: Incorrect Oil Specifications: Using low-quality engine oil can accelerate wear. Additionally, oil viscosity that is either too low or too high can lead to poor engine lubrication, increasing wear on piston rings and cylinder walls, reducing sealing performance, and resulting in oil burning. Excessive Clearance: Excessive clearance between piston rings and cylinder walls, improper piston ring installation, or degraded sealing can allow oil from the cylinder walls to enter the combustion chamber, causing oil burning.
8
5
Share

What happens if the car maintenance mileage is exceeded?

The hazards of exceeding the car maintenance mileage include: 1. If the engine oil exceeds the maintenance mileage, it will lead to poor oil fluidity and changes in viscosity properties. The engine will not be properly lubricated, resulting in increased wear and higher fuel consumption; 2. If the coolant exceeds the mileage, the cooling system's heat dissipation performance will decline. The deteriorated coolant can easily form scale in the system, reducing the engine's heat dissipation performance. Excessive temperature can easily cause the engine compartment to catch fire; 3. If the brake fluid exceeds the maintenance mileage, its boiling point will decrease. Prolonged or frequent braking can cause the brake fluid temperature to rise and boil, producing bubbles that directly lead to weak or failed braking.
11
3
Share

How to Turn on the Air Conditioning in a Santana 2000?

Press the A/C button to turn on the air conditioning in a Santana 2000. Below is a related introduction on how to set the air conditioning in a Santana: 1. Enter the Santana's driver's compartment to see the air conditioning control area; 2. The knob on the left is the temperature adjustment knob, turning clockwise increases the temperature; 3. The knob in the middle adjusts the air volume, with numbers indicating the fan speed level; 4. The knob on the right can adjust the defrosting of the windshield; 5. Toggle the switch to set the car's internal circulation mode or external circulation mode; 6. The A/C button is the cooling switch for the air conditioning.
14
5
Share

How to Replace the Battery in a Nissan Sylphy Key Fob?

Nissan Sylphy's key fob battery replacement method is as follows: Step 1: Remove the mechanical key. Step 2: Use a flat-head screwdriver to pry open a small gap from the side seam of the key fob, then continue prying along the opening. Insert your fingernail into the middle seam of the remote, slowly squeeze it, and gently pry outward with some force. Step 3: Use the flat-head screwdriver to remove the old battery and insert the new one. Note that the positive (+) side of the battery should face downward. Step 4: Reinstall the circuit board into position, align the key fob cover properly, and press firmly to secure it.
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.